- Unconditionally call *_stop() if device is in the tree. This is to
prevent callouts from happening after the device is gone. Checks for
bus_child_present() should be added in the future to keep from touching
potentially non-existent hardware in *_detach(). Found by iedowse@.
- Always check for and free miibus children, even if the device is not in
the tree since some failure cases could have gotten here.
- Call ether_ifdetach() in the irq setup failure case
- ti(4), xl(4): move ifmedia_init() calls to the beginning of attach so
that ifmedia_removeall() can be unconditionally called on detach. There
is no way to detect whether ifmedia has been initialized without using
a separate variable (as tl(4) does).
- Add comments to indicate assumptions of code path
bytes_in_mbuf rather than MCLBYTES. Add the ethertnet header to the
front of the mbuf. Adjust bytes_in_mbuf inside the loop that reads
the packet out of the card.
generation number back to a long (sizeof(u_int) != sizeof(long) on
sparc64). The alternative would have been to heavily change the libdevstat API.
Discussed with: phk, ken
codec during initialization. This code mirrors the reset code used on
the VIA82c686 and fixes a codec initialization failure (SoundMAX
AD1885) reported by Matthias Schuendehuette.
in dc_detach() instead of only calling it if the hardware is preset.
This is a workaround for page faults in softclock() after a `dc'
device was detached, caused by not disabling a timer before freeing
its memory. The bus_child_present() checks should probably be
re-added later, but only to avoid the hardware accesses and not the
other resource cleanups in dc_stop().
Approved by: njl
Many internal structure changes for the FireWire driver.
- Compute CRC in CROM parsing.
- Add support for configuration ROM build.
- Simplify dummy buffer handling.
- busdma conversion
- Use swi_taskqueue_giant for -current. Mark the interrupt routine as MPSAFE.
- AR buffer handling.
Don't reallocate AR buffer but just recycle it.
Don't malloc and copy per packet in fwohci_arcv().
Pass packet to fw_rcv() using iovec.
Application must prepare receiving buffer in advance.
- Change fw_bind API so that application should pre-allocate xfer structure.
- Add fw_xfer_unload() for recycling struct fw_xfer.
- Add post_busreset hook
- Remove unused 'sub' and 'act_type' in struct fw_xfer.
- Remove npacket from struct fw_bulkxfer.
- Don't call back handlers in fwochi_arcv() if the packet has
not drained in AT queue
- Make firewire works on big endian platform.
- Use native endian for packet header and remove unnecessary ntohX/htonX.
- Remove FWXFERQ_PACKET mode. We don't use it anymore.
- Remove unnecessary restriction of FWSTMAXCHUNK.
- Don't set root node for phy config packet if the root node is
not cycle master capable but set myself for root node.
We should be the root node after next bus reset.
Spotted by: Yoshihiro Tabira <tabira@scd.mei.co.jp>
- Improve self id handling
Tested on: i386, sparc64 and i386 with forced bounce buffer
blocking allocation could occur as a result of a label
initialization. This will simulate the behavior of allocated
label policies such as MLS and Biba when running mac_test from
the perspective of WITNESS lock and sleep warnings.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
command config register. At the present, this represents a nop
because these bits should have been set earlier in the process. In
the future, we'll only set these bits when the driver requests the
resource, not when the bus code detects the resource.
Reviewed by: mdodd
don't try and convert the argument flags to malloc flags, or we risk
implicitly requesting blocking and generating witness warnings.
Obtained from: TrustedBSD Project
Sponsored by: DARPA, Network Associates Laboratories
