- PR-SCTP had major issues when skipping through a multi-part message.
o Did not look at socket buffer.
o Did not properly handle the reassmebly queue.
o The MARKED segments could interfere and un-skip a chunk causing
a problem with the proper FWD-TSN.
o No FR of FWD-TSN's was being done.
- NR-Sack code was basically disabled. It needed fixes that
never got into the real code.
- CMT code had issues when the two paths were NOT the same b/w. We
found a few small bugs, but also the critcal one here was not
dividing the rwnd amongst the paths.
Obtained from: Michael Tuexen and myself at the IETF hack-fest ;-)
- When sending large PR-SCTP messages over a
lossy link we would incorrectly calculate the fwd-tsn
- When receiving large multipart pr-sctp packets we would
incorrectly send back a SACK that would renege improperly
on already received packets thus causing unneeded retransmissions.
1) WP should never be marked unless flight size is 0
2) When recovering from wp if the peer ack's it we don't mark for retran
3) When recovering, we must assure a timer is still running.
into the advance_peer_ack point so we would incorrectly
send a wrong value in the FWD-TSN
- PR-SCTP bug, where an PR packet is used for a window
probe which could incorrectly get the packet moved
back into the send_queue, which will cause major issues and
should not happen.
- Fix a trace to use the proper macro.
bit of debugging afterwards):
- Fix protection code for notification generation.
- Decouple associd from vtag
- Allow vtags to have less strigent requirements in non-uniqueness.
o don't pre-hash them when you issue one in a cookie.
o Allow duplicates and use addresses and ports to
discriminate amongst the duplicates during lookup.
- Add support for the NAT draft draft-ietf-behave-sctpnat-00, this
is still experimental and needs more extensive testing with the
Jason Butt ipfw changes.
- Support for the SENDER_DRY event to get DTLS in OpenSSL working
with a set of patches from Michael Tuexen (hopefully heading to OpenSSL soon).
- Update the support of SCTP-AUTH by Peter Lei.
- Use macros for refcounting.
- Fix MTU for UDP encapsulation.
- Fix reporting back of unsent data.
- Update assoc send counter handling to be consistent with endpoint sent counter.
- Fix a bug in PR-SCTP.
- Fix so we only send another FWD-TSN when a SACK arrives IF and only
if the adv-peer-ack point progressed. However we still make sure
a timer is running if we do have an adv_peer_ack point.
- Fix PR-SCTP bug where chunks were retransmitted if they are sent
unreliable but not abandoned yet.
With the help of: Michael Teuxen and Peter Lei :-)
MFC after: 4 weeks
-Improvement: panic() on INVARIANTS kernels if memory allocation
fails for a tagblock in sctp_add_vtag_to_timewait().
-Bugfix: Protect code in sctp_is_in_timewait() by
SCTP_INP_INFO_WLOCK/SCTP_INP_INFO_WUNLOCK.
-Cleanup: Get rid of unused variable now in sctp_init_asoc().
-Bugfix: Reuse the correct vtag in sctp_add_vtag_to_timewait().
-Cleanup: Get rid of unused constant SCTP_TIME_WAIT_SHORT
in sctp_constants.h.
-Improvement: Use all hash buckets of the vtag hash table.
-Cleanup: Get rid of then unused constant SCTP_STACK_VTAG_HASH_SIZE_A.
-Bugfix: Handle SHUTDOWN;SACK packet correctly.
-Bugfix: Last TSN in a gap ack block was not being "ack'd"
in the internal scoreboard.
Obtained from: (with help from Michael Tuexen)
- Change it so that without INVARIANTs there are
no panics in SCTP.
- sctp_timer changes so that we have a recovery mechanism
when the sent list is out of order.
2) Adds some __UserSpace__ on some of the common defines that
the user space code needs
3) Fixes a bug when we send up data to a user that failed. We
need to a) trim off the data chunk headers, if present, and
b) make sure the frag bit is communicated properly for the
msgs coming off the stream queues... i.e. we see if some
of the msg has been taken.
Obtained from: jeli contributed the VIMAGE changes on this pass Thanks Julain!
- Vimage prep - these are major restructures to move
all global variables to be accessed via a macro or two.
The variables all go into a single structure.
- Asconf address addition tweaks (add_or_del Interfaces)
- Fix rwnd calcualtion to be more conservative.
- Support SACK_IMMEDIATE flag to skip delayed sack
by demand of peer.
- Comment updates in the sack mapping calculations
- Invarients panic added.
- Pre-support for UDP tunneling (we can do this on
MAC but will need added support from UDP to
get a "pipe" of UDP packets in.
- clear trace buffer sysctl added when local tracing on.
Note the majority of this huge patch is all the vimage prep stuff :-)
- Adds some prepwork (Not all yet) for vimage in particular
support the delete the sctppcbinfo.xx structs. There is
still a leak in here if it were to be called plus we stil
need the regrouping (From Me and Michael Tuexen)
- Adds support for UDP tunneling. For BSD there is no
socket yet setup so its disabled, but major argument
changes are in here to emcompass the passing of the port
number (zero when you don't have a udp tunnel, the default
for BSD). Will add some hooks in UDP here shortly (discussed
with Robert) that will allow easy tunneling. (Mainly from
Peter Lei and Michael Tuexen with some BSD work from me :-D)
- Some ease for windows, evidently leave is reserved by their
compile move label leave: -> out:
MFC after: 1 week
- fix a bug during cookie collision that prevented an
association from coming up in a specific restart case.
- Fix it so the shutdown-pending flag gets removed (this is
more for correctness then needed) when we enter shutdown-sent
or shutdown-ack-sent states.
- Fix a bug that caused the receiver to sometimes NOT send
a SACK when a duplicate TSN arrived. Without this fix
it was possible for the association to fall down if the
- Deleted primary destination is also stored when SCTP_MOBILITY_BASE.
(Previously, it is stored when only SCTP_MOBILITY_FASTHANDOFF)
- Fix a locking issue where we might call send_initiate_ack() and
incorrectly state the lock held/not held. Also fix it so that
when we release the lock the inp cannot be deleted on us.
- Add the debug option that can cause the stack to panic instead
of aborting an assoc. This does not and should never show up
in options but is useful for debugging unexpected aborts.
- Add cumack_log sent to track sending cumack information for
the debug case where we are running a special log per assoc.
- Added extra () aroudn sctp_sbspace macro to avoid compile warnings.
MFC after: 1 week
retransmittion by handover event (fast mobility code)
- Fixed problem of mobility code which is caused by remaining
parameters in the deleted primary destination.
- Add a missing lock. When a peer sends an INIT, and while we
are processing it to send an INIT-ACK the socket is closed,
we did not hold a lock to keep the socket from going away.
Add protection for this case.
- Fix so that arwnd is alway uses the minimal rwnd if the user
has set the socket buffer smaller. Found this when the test
org decided to see what happens when you set in a rwnd of 10
bytes (which is not allowed per RFC .. 4k is minimum).
- Fixes so a cookie-echo ootb will NOT cause an abort to
be sent. This was happening in a MPI collision case.
- Examined all panics and unless there was no recovery, moved
any that were not already to INVARANTS.
Approved by: re@freebsd.org (gnn)
stream (using EEOR mode). Changed to EINVAL (in sctp_output.c)
- Static analysis comments added
- fix in mobility code to return a value (static analysis found).
- sctp6_notify function made visible instead of
static (this is needed for Panda).
Approved by: re@freebsd.org (B Mah)
the recent send code, but uio may be NULL on sendfile
calls. Change to use sndlen variable.
- EMSGSIZE is not being returned in non-blocking mode
and needs a small tweak to look if the msg would
ever fit when returning EWOULDBLOCK.
- FWD-TSN has a bug in stream processing which could
cause a panic. This is a follow on to the codenomicon
fix.
- PDAPI level 1 and 2 do not work unless the reader
gets his returned buffer full. Fix so we can break
out when at level 1 or 2.
- Fix fast-handoff features to copy across properly on
accepted sockets
- Fix sctp_peeloff() system call when no true system call
exists to screen arguments for errors. In cases where a
real system call exists the system call itself does this.
- Fix raddr leak in recent add-ip code change for bundled
asconfs (even when non-bundled asconfs are received)
- Make sure ipi_addr lock is held when walking global addr
list. Need to change this lock type to a rwlock().
- Add don't wake flag on both input and output when the
socket is closing.
- When deleting an address verify the interface is correct
before allowing the delete to process. This protects panda
and unnumbered.
- Clean up old sysctl stuff and get rid of the old Open/Net
BSD structures.
- Add a function to watch the ranges in the sysctl sets.
- When appending in the reassembly queue, validate that
the assoc has not gone to about to be freed. If so
(in the middle) abort out. Note this especially effects
MAC I think due to the lock/unlock they do (or with
LOCK testing in place).
- Netstat patch to get rid of warnings.
- Make sure that no data gets queued to inactive/unconfirmed
destinations. This especially effect CMT but also makes a
impact on regular SCTP as well.
- During init collision when we detect seq number out
of sync we need to treat it like Case C and discard
the cookie (no invarient needed here).
- Atomic access to the random store.
- When we declare a vtag good, we need to shove it
into the time wait hash to prevent further use. When
the tag is put into the assoc hash, we need to remove it
from the twait hash (where it will surely be). This prevents
duplicate tag assignments.
- Move decr-ref count to better protect sysctl out of
data.
- ltrace error corrections in sctp6_usrreq.c
- Add hook for interface up/down to be sent to us.
- Make sysctl() exported structures independent of processor
architecture.
- Fix route and src addr cache clearing for delete address case.
- Make sure address marked SCTP_DEL_IP_ADDRESS is never selected
as src addr.
- in icmp handling fixed so we actually look at the icmp codes
to figure out what to do.
- Modified mobility code.
Reception of DELETE IP ADDRESS for a primary destination and
SET PRIMARY for a new primary destination is used for
retransmission trigger to the new primary destination.
Also, in this case, destination of chunks in send_queue are
changed to the new primary destination.
- Fix so that we disallow sending by mbuf to ever have EEOR
mode set upon it.
Approved by: re@freebsd.org (B Mah)
additional flags to many function calls. The flags only
get used in BSD when we compile with lock testing. These
flags allow apple to escape the "giant" lock it holds on
the socket and have more fine-grained locking in the NKE.
It also allows us to test (with witness) the locking used
by apple via a compile switch (manually applied).
Approved by: re@freebsd.org(B Mah)
the last message on the send stream was "null" but still
there, a state we allow, we could get hung and not clean
it up and wait for the shutdown guard timer to clear the
association without a graceful close. Fix this so that
that we properly clean up.
- Added support for Multiple ASCONF per new RFC. We only
(so far) accept input of these and cannot yet generate
a multi-asconf.
- Sysctl'd support for experimental Fast Handover feature. Always
disabled unless sysctl or socket option changes to enable.
- Error case in add-ip where the peer supports AUTH and ADD-IP
but does NOT require AUTH of ASCONF/ASCONF-ACK. We need to
ABORT in this case.
- According to the Kyoto summit of socket api developers
(Solaris, Linux, BSD). We need to have:
o non-eeor mode messages be atomic - Fixed
o Allow implicit setup of an assoc in 1-2-1 model if
using the sctp_**() send calls - Fixed
o Get rid of HAVE_XXX declarations - Done
o add a sctp_pr_policy in hole in sndrcvinfo structure - Done
o add a PR_SCTP_POLICY_VALID type flag - yet to-do in a future patch!
- Optimize sctp6 calls to reuse code in sctp_usrreq. Also optimize
when we close sending out the data and disabling Nagle.
- Change key concatenation order to match the auth RFC
- When sending OOTB shutdown_complete always do csum.
- Don't send PKT-DROP to a PKT-DROP
- For abort chunks just always checksums same for
shutdown-complete.
- inpcb_free front state had a bug where in queue
data could wedge an assoc. We need to just abandon
ones in front states (free_assoc).
- If a peer sends us a 64k abort, we would try to
assemble a response packet which may be larger than
64k. This then would be dropped by IP. Instead make
a "minimum" size for us 64k-2k (we want at least
2k for our initack). If we receive such an init
discard it early without all the processing.
- When we peel off we must increment the tcb ref count
to keep it from being freed from underneath us.
- handling fwd-tsn had bugs that caused memory overwrites
when given faulty data, fixed so can't happen and we
also stop at the first bad stream no.
- Fixed so comm-up generates the adaption indication.
- peeloff did not get the hmac params copied.
- fix it so we lock the addr list when doing src-addr selection
(in future we need to use a multi-reader/one writer lock here)
- During lowlevel output, we could end up with a _l_addr set
to null if the iterator is calling the output routine. This
means we would possibly crash when we gather the MTU info.
Fix so we only do the gather where we have a src address
cached.
- we need to be sure to set abort flag on conn state when
we receive an abort.
- peeloff could leak a socket. Moved code so the close will
find the socket if the peeloff fails (uipc_syscalls.c)
Approved by: re@freebsd.org(Ken Smith)
when peer acks the add in case the routing table changes.
- Fix sctp_lower_sosend to send shutdown chunk for mbuf send
case when sndlen = 0 and sinfoflag = SCTP_EOF
- Fix sctp_lower_sosend for SCTP_ABORT mbuf send case with null data,
So that it does not send the "null" data mbuf out and cause
it to get freed twice.
- Fix so auto-asconf sysctl actually effect the socket's asconf state.
- Do not allow SCTP_AUTO_ASCONF option to be used on subset bound sockets.
- Memset bug in sctp_output.c (arguments were reversed) submitted
found and reported by Dave Jones (davej@codemonkey.org.uk).
- PD-API point needs to be invoked >= not just > to conform to socket api
draft this fixes sctp_indata.c in the two places need to be >=.
- move M_NOTIFICATION to use M_PROTO5.
- PEER_ADDR_PARAMS did not fail properly if you specify an address
that is not in the association with a valid assoc_id. This meant
you got or set the stcb level values instead of the destination
you thought you were going to get/set. Now validate if the
stcb is non-null and the net is NULL that the sa_family is
set and the address is unspecified otherwise return an error.
- The thread based iterator could crash if associations were freed
at the exact time it was running. rework the worker thread to
use the increment/decrement to prevent this and no longer use
the markers that the timer based iterator uses.
- Fix the memleak in sctp_add_addr_to_vrf() for the case when it is
detected that ifa is already pointing to a ifn.
- Fix it so that if someone is so insane that they drop the
send window below the minimal add mark, they still can send.
- Changed all state for associations to use mask safe macro.
- During front states in association freeing in sctp_inpcbfree, we
had a locking problem where locks were not in place where they
should have been.
- Free association calls were not testing the return value in
sctp_inpcb_free() properly... others should be cast void returns
where we don't care about the return value.
- If a reference count is held on an assoc, even from the "force free"
we should not do the actual free.. but instead let the timer
free it.
- When we enter sctp_input(), if the SCTP_ASOC_ABOUT_TO_BE_FREED
flag is set, we must NOT process the packet but handle it like
ootb. This is because while freeing an assoc we release the
locks to get all the higher order locks so we can purge all
the hash tables. This leaves a hole if a packet comes in
just at that point. Now sctp_common_input_processing() will
call the ootb code in such a case.
- Change MBUF M_NOTIFICATION to use M_PROTO5 (per Sam L). This makes
it so we don't have a conflict (I think this is a covertity change).
We made this change AFTER some conversation and looking to make sure
that M_PROTO5 does not have a problem between SCTP and the 802.11
stuff (which is the only other place its used).
- Fixed lock order reversal and missing atomic protection around
locked_tcb during association lookup and the 1-2-1 model.
- Added debug to source address selection.
- V6 output must always do checksum even for loopback.
- Remove more locks around inp that are not needed for an atomically
added/subtracted ref count.
- slight optimization in the way we zero the array in sctp_sack_check()
- It was possible to respond to a ABORT() with bad checksum with
a PKT-DROP. This lead to a PKT-DROP/ABORT war. Add code to NOT
send a PKT-DROP to any ABORT().
- Add an option for local logging (useful for macintosh or when
you need better performing during debugging). Note no commands
are here to get the log info, you must just use kgdb.
- The timer code needs to be aware of if it needs to call
sctp_sack_check() to slide the maps and adjust the cum-ack.
This is because it may be out of sync cum-ack wise.
- Added threshold managment logging.
- If the user picked just the right size, that just filled the send
window minus one mtu, we would enter a forever loop not copying and
at the same time not blocking. Change from < to <= solves this.
- Sysctl added to control the fragment interleave level which defaults
to 1.
- My rwnd control was not being used to control the rwnd properly (we
did not add and subtract to it :-() this is now fixed so we handle
small messages (1 byte etc) better to bring our rwnd down more
slowly.
Approved by: re@freebsd.org (Bruce Mah)
- remove duplicate #include <sys/priv.h> that is not under
#ifdef FreeBSD version to allow compile on 6.1
- static analysis changes per the cisco SA tool including:
o some SA_IGNORE comments
o some checks for NULL before unlock.
o type corrections int -> size_t
- Fix it so sctp_alloc_asoc takes a thread/proc argument. Without this
we pass a NULL in to bind on implicit assoc setup and crash :-(
Approved by: re@freebsd.org(Ken Smith)
- use proper tick gathering macro instead of ticks directly.
- Placed reasonable boundaries on sets that a user can do
that are converted to ticks from ms.
- Fix CMT_PF to always check to be sure CMT is on.
- Fix ticks use of CMT_PF.
- put back code to allow asconfs to be queued while INITs are in flight
and before the assoc is established.
- During window probes, an ack'd packet might be left with the window
probe mark on it causing it to be retransmitted. Change so that
the flight decrease macro clears the window_probe mark.
- Additional logging flight size/reading and ASOC LOG. This
is only enabled if you manually insert things into opt_sctp.h
since its a set of debug code only.
- Found an interesting SMP race in the way data was appended which
could cause a reader to lose a part of a message, had to
reorder when we marked the message was complete to after
the data was appended.
- bug in ADD-IP for the subset bound socket case when the peer has only
one address
- fix ASCONF implicit success/error handling case
- proper support of jails in Freebsd 6>
- copy out the timeval for the 64 bit sparc world on cookie-echo
alignment error crashes without this).
Approved by: re(Ken Smith)
- CMT_PF states added (w/sysctl to turn the PF version on)
- sctp_input.c had a missing incr of cookie case when the
auth was bad. This meant a free was called without an
increment to refcnt, added increment like rest of code.
- There was a case, unlikely, when the scope of the destination
changed (this is a TSNH case). In that case, it would not free
the alloc'ed asoc (in sctp_input.c).
- When listed addresses found a colliding cookie/Init, then
the collided upon tcb was not unlocked in sctp_pcb.c
- Add error checking on arguments of sctp_sendx(3) to prevent it from
referencing a NULL pointer.
- Fix an error return of sctp_sendx(3), it was returing
ENOMEM not -1.
- Get assoc id was changed to use the sanctified socket api
method for getting a assoc id (PEER_ADDR_INFO instead of
PEER_ADDR_PARAMS).
- Fix it so a peeled off socket will get a proper error return
if it trys to send to a different address then it is connected to.
- Fix so that select_a_stream can avoid an endless loop that
could hang a caller.
- time_entered (state set time) was not being set in all cases
to the time we went established.
Approved by: re(ken smith)
call the sctp_free_remote_address() function.
- Assure that when we allocate a chunk the whoTo is NULL,
also when we free it and place it into the cache we NULL
it (that way the consolidation code will always work).
- Fix a small race, when a empty data holder is left on the stream
out queue, and both sides do a shutdown, the empty data holder
would prevent us from sending a SHUTDOWN-ACK and at the same time we
never would cleanup the empty holder (since nothing was ever in queue).
We now add a utility function that a) cleans up empty holders and
b) properly determines if there are still pending data chunks on
the stream out wheel.
Approved by: re@freebsd.org (Ken Smith)
- Fix fwd-tsn to use proper accessor so it does not overrun mbufs
- Fix stream reset error reporting to actually work (it has always been
broken if the peer rejects a stream reset)
- Some 64 bit friendly changes
Approved by: re(bmah@freebsd.org)
thinking it had the whole chunk. This could cause a crash if
a large packet drop came in. Fixed by adjusting the trunc length
down to the limit.
- Large sacks with lots of segments could also have same issue. Changed
duplicate and segment handling to use proper get_m_ptr function to
pull each block from mbuf chains.
- Fix so VRF's will clean themselves up when no references are around.
- Allow sctp_ifa to be passed into inpcb_bind, addr_mgmt_ep_sa to bypass
normal validation checks.
- turn auto-asconf off for subset bound sockets
- Moves all logging to use KTR. This gets rid of most
of the logging #ifdef's with a few exceptions reducing
the number of config options for SCTP.
default_vrf_id
- Missing lock/unlock of inp added as well in the v6 side.
- IFN hash table moves to sctppcbinfo since indexes are
unique across systems (including different VRFs) this makes it easier
to do ifn lookups.
concept that is NOT well thought out for a multi-homed transport
protocol. So the useless table-id entries passed around need to
be removed.
- Add a event timer for the zero copy api.
- Fix a bug in sctp_timer.c when searching for an alternate
with the largest ssthresh (the compare was wrong).
is expanded, size of expansion was not taken int consideration.
- Fix so vtag hash is 1 bigger so that it modulo's out
correctly, avoids a panic when restart with right modulo happens.
- do not dereference stcb when control->do_not_ref_stcb is set
- Fix up packet logging to not often use a lock and also to
add to options.
- Fix some logging option duplication in the sctputil.h
hold a wq lock for the iterator. Panda uses a
silly recursive lock they hold through the timer.
- Add poor mans wireshark compile option..
- Allocate and start using SCTP_M_XXX for all SCTP_MALLOC() calls.
- sysctl now will get back the refcnt for viewing by onlookers.
Reviewed by: gnn
- bounded cookie-life to 1 second minimum in socket option set.
- Delayed_ack_time becomes delayed_ack per new socket api document.
- Improve port number selection, we now use low/high bounds and
no chance of a endless loop. Only one call to random per bind
as well.
- fixes so set_peer_primary pre-screens addresses to be
valid to this host.
- maxseg did not allow setting on an assoc basis. We needed
to thus track and use an association value instead of a inp value.
- Fixed ep get of HB status to report back properly.
- use settings flag to tell if assoc level hb is on off not
the timer.. since the timer may still run if unconf address
are present.
- check for crazy ENABLE/DISABLE conditions.
- set and get of pmtud (fixed path mtu) not always taking into account ovh.
- Getting PMTU info on stcb only needs to return PMTUD_ENABLED if
any net is doing PMTU discovery.
- Panic or warning fixed to not do so when a valid ip frag is
taking place.
- sndrcvinfo appearing in both inp and stcb was full size, instead
of the non-pad version. This saves about 92 bytes from each struct
by carefully converting to use the smaller version.
- one-2-one model get(maxseg) would always get ep value, never the
tcb's value.
- The delayed ack time could be under a tick, this fixes so
it bounds it to at least 1 tick for platforms whos tick
is more than a ms.
- Fragment interleave level set to wrong default value.
- Fragment interleave could not set level 0.
- Defered stream reset was broken due to a guard check and ntohl issue.
- Found two lock order reversals and fixed.
- Tighten up address checking, if the user gives an address the sa_len
had better be set properly.
- Get asoc by assoc-id would return a locked tcb when it was asked
not to if the tcb was in the restart hash.
- sysctl to dig down and get more association details
Reviewed by: gnn
- Fixed RTOinfo for bounding.
- Fixed connect() to return ECONNREFUSED when an ABORT is received.
- Added comments to direct Static Analysis not to look at some things
it does not understand (comments are /* sa_ignore XXXXX */)
- Bind when colliding was broken, missing not_found = 1 before
checking to see if the port was in use caused endless bind loop.
- Cookie life needs to be in milliseconds to conform to socket api.
- Cookie life is not supposed to change if its 0, On the assoc
level set we changed it to 0 opps.
- Two more static analysis issues identified by the cisco
tool. Null checks needed.
- An issue for sendfile(). Need to validate the correct
input argument.
- When sending failed due to a no route to host, we leaked
the mbuf chain failing to call m_freem().
- Fix #ifdef issue for getting hash block len when HAVE_SHA2 is NOT defined
Reviewed by: gnn
- All printf that was surrounded by #ifdef SCTP_DEBUG moves to
a macro that does all of this. This removes all printfs from
the code and makes the code more portable and easier to
read.
- Static Analysis (cisco) - found a few bugs, but mostly we
add checks for NULL pointers and such to make the tool
happy. We now pass the Cisco SA tools checks except for
where it does not understand tailq/lists. We still need
to look at the coverity tools output too (this is like
the cisco SA tool) and see if it wants us to fix any other
items. Hopefully this will be the last major churn in the
code other than bug fixes.
to the coverity tool.. may even be the same one.. not sure).
- A bug in the way sctp_abort() and friends were
setting the IP_CLOSE flag.. and NOT passing the
last argument as a (,1)... so that things would
get freed..
- PR-SCTP would ignore FWD-TSN's above a rwnd's worth
of TSN's (1 byte msgs).. this left the peer hopelessly
out of sync.. or an attacker. So now we abort the assoc.
- New IFN hash, also rename hashes to match addr/ifn now
that the vrf has multiple.
- Do not enable SCTP_PCB_FLAGS_RECVDATAIOEVNT per default
as defined in the Socket API ID.
- Export MTU information via sysctl.
- Vrf's need table id's. This is default for
BSD, but may be other things later when BSD
fully supports VRFs.
- Additional stream reset bug (caught by cisco dev-test).
- Additional validations for the address in sending a message (socket api).
-------- and -----
- Fix association notifications not to give the active open
side false notifications.
- Fix so sendfile and SENDALL will work properly (missing
flag to say socket sender is done).
- Fix Bug that prevented COOKIES from being retransmitted.
- Break out connectx into helper sub-models so that iox routines can
reuse the helpers.
- When an address is added during system init (non-dynamic mode) make
sure that the "defer use" flag is not set.
** its compiling on XR now :-D **
Reviewed by: gnn
set/clear it but would not do it. Now we will.
- Moved to latest socket api for extended sndrcv info struct.
- Moved to support all new levels of fragment interleave (0-2).
- Codenomicon security test updates - length checks and such.
- Bug in stream reset (2 actually).
- setpeerprimary could unlock a null pointer, fixed.
- Added a flag in the pcb so netstat can see if we are listening easier.
Obtained from: (some of the Listen changes from Weongyo Jeong)
set/clear it but would not do it. Now we will.
- Moved to latest socket api for extended sndrcv info struct.
- Moved to support all new levels of fragment interleave.
- Removed free-oqueue cache.
- Fix counter for sq entries
- Increased the amount of information retained
on ASOC_TSN logging on the association.
- Made it so with the ASOC_TSN logging on
sending or recieving an abort we dump the log.
- Went through and added invariant's around some
panic's that needed them.
- decrements went to atomic_subtact_int instead of add -1
- Removed residual count increment that threw off a
strm oq count.
- Tracks and complaints if we don't have a LAST fragment and
clean up the sp structure.
- Track a new stat that counts number of abandoned msgs that
happen if you close without reading.
- Fix lookup of frag point to be aware of a 0 assoc-id.
Reviewed by: gnn
- name change of prefered -> preferred
- CMT fast recover code added.
- Comment fixes in CMT.
- We were not giving a reason of cant_start_asoc per socket api
if we failed to get init/or/cookie to bring up an assoc. Change
so we don't just give a generic "comm lost" but look at actual
states of dying assoc.
- change "crc32" arguments to "crc32c" to silence strict/noisy
compiler warnings when crc32() is also declared
- A few minor tweaks to get the portable stuff truely portable
for sctp6_usrreq.c :-D
- one-2-one style vrf match problem.
- window recovery would leave chks marked for retran
during window probes on the sent queue. This would then
cause an out-of-order problem and assure that the flight
size "problem" would occur.
- Solves a flight size logging issue that caused rwnd
overruns, flight size off as well as false retransmissions.g
- Macroize the up and down of flight size.
- Fix a ECNE bug in its counting.
- The strict_sacks options was causing aborts when window probing
was active, fix to make strict sacks a bit smarter about what
the next unsent TSN is.
- Fixes a one-2-one wakeup bug found by Martin Kulas.
- If-defed out form, Andre's copy routines pending his
commit of at least m_last().. need to adjust for 6.2 as
well.. since m_last won't exist.
Reviewed by: gnn
- fixed a refcount bug in the new ifa structures.
- use vrf's from default stcb or inp whenever possible.
- Address limits raised to account for a full IP fragmented
packet (1000 addresses).
- flight size correcting updated to include one message only
and to handle case where the peer does not cumack the
next segment aka lists 1/1 in sack blocks..
- Various bad init/init-ack handling could cause a panic
since we tried to unlock the destroyed mutex. Fixes
so we properly exit when we need to destroy an assoc.
(Found by Cisco DevTest team :D)
- name rename in src-addr-selection from pass to sifa.
- route structure typedef'd to allow different platforms
and updated into sctp_os_bsd file.
- Max retransmissions a chunk can be made added.
Reviewed by: gnn
incorrect, non-bundlable fragmentation.
- Added min residual to better control split points for
both how big a msg must be as well as how much needs
to be left over.
- With our new algo in place, we need to implicitly
set "end of msg" on the sp-> structure otherwise we
end up with "hung" associations.
- Room reserved up front in IP header by pushing IP
header to back of mbuf.
- Fix so FR's peg count of retransmissions needed.
- Fix so an unlucky chunk that never gets across
will kill the assoc via the kill timer and send an
abort too.
- Fix bug in sctp_input which can result in a crash.
- Do not strip off IP options anymore.
- Clean up sctp_calculate_rto().
- Get rid of unused sysctl.
- Fixed so we discard all M-Cast
- Fixed so port check done AFTER checksum
- Fixed bug in fragmentation code that prevented
us from fragmenting a small complete message when
we needed to.
- Window probes were not marked back to unsent and
flight adjusted when a sack came in with no
window change or accepting of the probe data.
We now fix this with having a mark on the net and
the chunk so we can clear it out when the sack arrives
forcing it to retran just like it was "new" this
improves the handling of window probes, which were
dropped by the receiver.
- Tighten AUTH protocol error checks during INIT/INIT-ACK exchange
shutdown which caused extra abort from peer.
- RTT time calculation was not being done in
express sack handling since it refered to an unused
variable (rto_pending). Removed variable.
- socket buffer high water access macro-ized.
- SB_CLEAR macro defined and used for sb clearing.
- Fix for CMT express_sack_handling did not do proper
pseudo-cumack updates.
- Get rid of extraneous function that was never used ip_2_ip6_hdr()
- Fixed source address selection bug (initialization problem).
- Source address selection debug added.
- moved away from ifn/ifa access to sctp_ifa/sctp_ifn
built and managed by the add-ip code.
- cleaned up add-ip code to use the iterator
- made iterator be a thread, which enables auto-asconf now.
- rewrote and cleaned up source address selection (also
made it use new structures).
- Fixed a couple of memory leaks.
- DACK now settable as to how many packets to delay as
well as time.
- connectx() to latest socket API, new associd arg.
- Fixed issue with revoking and loosing potential to
send when we inflate the flight size. We now inflate
the cwnd too and deflate it later when the revoked
chunk is sent or acked.
- Got rid of some temp debug code
- src addr selection moved to a common file (sctp_output.c)
- Support for simple VRF's (we have support for multi-vfr
via compile switch that is scrubbed from BSD but we won't
need multi-vrf until we first get VRF :-D)
- Rest of mib work for address information now done
- Limit number of addresses in INIT/INIT-ACK to
a #def (30).
Reviewed by: gnn
