Sponsored by: BQ Internet
sys/dev/xen/netfront/netfront.c:
o Implement netfront_suspend(), a specialized suspend
handler for the netfront driver. This routine simply
disables the carrier so the driver is idle during
system suspend processing.
o Fix a leak when re-initializing LRO during a link reset.
o In netif_release_tx_bufs(), when cleaning up the grant
references for our TX ring, use gnttab_end_foreign_access_ref
instead of attempting to grant the page again.
o In netif_release_tx_bufs(), we do not track mbufs associated
with mbuf chains, but instead just free each mbuf directly.
Use m_free(), not m_freem(), to avoid double frees of mbufs.
o Refactor some code to enhance clarity.
Approved by: re
MFC after: 1 week
Sponsored by: BQ Internet
sys/dev/xen/blkfront/block.h:
sys/dev/xen/blkfront/blkfront.c:
Remove now unused blkif_vdev_t from the blkfront soft.
sys/dev/xen/blkfront/blkfront.c:
o In blkfront_suspend(), indicate the desire to suspend
by changing the softc connected state to SUSPENDED, and
then wait for any I/O pending on the remote peer to
drain. Cancel suspend processing if I/O does not
drain within 30 seconds.
o Enable and update blkfront_resume(). Since I/O is
drained prior to the suspension of the VM, the complicated
recovery process performed by other Xen blkfront
implementations is avoided. We simply tear down the
connection to our old peer, and then re-connect.
o In blkif_initialize(), fix a resource leak and botched
return if we cannot allocate shadow memory for our
requests.
o In blkfront_backend_changed(), correct our response to
the XenbusStateInitialised state. This state indicates
that our backend peer has published sufficient data for
blkfront to publish ring information and other XenStore
data, not that a connection can occur. Blkfront now
will only perform connection processing in response to
the XenbusStateConnected state. This corrects an issue
where blkfront connected before the backend was ready
during resume processing.
Approved by: re
MFC after: 1 week
framework.
Sponsored by: BQ Internet
sys/xen/xenbus/xenbusb.c:
o In xenbusb_resume(), publish the state transition of the
resuming device into XenbusStateIntiailising so that the
remote peer can see it. Recording the state locally is
not sufficient to trigger a re-connect sequence.
o In xenbusb_resume(), defer new-bus resume processing until
after the remote peer's XenStore address has been updated.
The drivers may need to refer to this information during
resume processing.
sys/xen/xenbus/xenbusb_back.c:
sys/xen/xenbus/xenbusb_front.c:
Register xenbusb_resume() rather than bus_generic_resume()
as the handler for device_resume events.
sys/xen/xenstore/xenstore.c:
o Fix grammer in a comment.
o In xs_suspend(), pass suspend events on to the child
devices (e.g. xenbusb_front/back, that are attached
to the XenStore.
Approved by: re
MFC after: 1 week
This change fixes a race in device side mode during clear-stall from
host, which can cause data to be sent too early on the given
endpoint.
Approved by: re (kib)
MFC after: 1 week
initialization. Prior to this change packets may be transmitted with an
incorrect checksum.
Em(4) already has an equivalent change in r213234.
Obtained From: Sandvine
MFC After: 1 week
Approved by: re (bz)
patch modifies makesyscalls.sh to prefix all of the non-compatibility
calls (e.g. not linux_, freebsd32_) with sys_ and updates the kernel
entry points and all places in the code that use them. It also
fixes an additional name space collision between the kernel function
psignal and the libc function of the same name by renaming the kernel
psignal kern_psignal(). By introducing this change now we will ease future
MFCs that change syscalls.
Reviewed by: rwatson
Approved by: re (bz)
We are allocating some kilobytes of extra memory during USB device enumeration.
This does not change alot under FreeBSD, but makes sense for various embedded
operating systems using the FreeBSD USB stack, which have less memory
resources available.
Approved by: re (kib)
MFC after: 1 week
the BAR after parsing the CIS. This forces the resource range to be
reallocated if the BAR is reused by the device.
Submitted by: deischen
Reviewed by: imp
Approved by: re (kib)
This is another commit in a series of TDMA support fixes for the 11n NICs.
* Move ath_hal_getnexttbtt() into the HAL; write methods for it.
This returns a timer value in TSF, rather than TU.
* Move ath_hal_getcca() and ath_hal_setcca() into the HAL too, where they
likely now belong.
* Create a new HAL capability: HAL_CAP_LONG_RXDESC_TSF.
The pre-11n NICs write 15 bit TSF snapshots into the RX descriptor;
the AR5416 and later write 32 bit TSF snapshots into the RX descriptor.
* Use the new capability to choose between 15 and 31 bit TSF adjustment
functions in ath_extend_tsf().
* Write ar5416GetTsf64() and ar5416SetTsf64() methods.
ar5416GetTsf64() tries to compensate for TSF changes at the 32 bit boundary.
According to yin, this fixes the TDMA beaconing on 11n chipsets and TDMA
stations can now associate/talk, but there are still issues with traffic
stability which need to be investigated.
The ath_hal_extendtsf() function is also used in RX packet timestamping;
this may improve adhoc mode on the 11n chipsets. It also will affect the
timestamps seen in radiotap frames.
Submitted by: Kang Yin Su <cantona@cantona.net>
Approved by: re (kib)
whenever the link state is changed. Using software based polling
for media status tracking is known to cause MII access failure
under certain conditions once link is established so vge(4) used to
rely on link status change interrupt.
However DEVICE_POLLING completely disables generation of all kind
of interrupts on vge(4) such that this resulted in not detecting
link state change event. This means vge(4) does not correctly
detect established/lost link with DEVICE_POLLING. Losing the
interrupt made vge(4) not to send any packets to peer since vge(4)
does not try to send any packets when there is no established link.
Work around the issue by generating link state change interrupt
with DEVICE_POLLING.
PR: kern/160442
Approved by: re (kib)
reference driver does clear the async interrupts after each service.
I'll tinker with this in a future commit.
Obtained from: Atheros
Approved by: re (kib)
When the fast clock (44mhz) is enabled for 5ghz HT20, the
dual ADCs aren't enabled. Trying to do the ADC calibrations
here would result in calibration never completing; this
resulted in IQ calibration never running and thus performance
issues in 11a/11n HT20 mode.
Leave it enabled for non-fastclock (40mhz) 11a mode and
HT40 modes.
This has been fixed in discussion with Felix Fietkau (nbd)
and discussions with the Atheros baseband team.
Linux ath9k now has a similar fix.
Approved by: re (kib)
The current code was rounding down the maximum frame size instead of
routing up, resulting in a read size of 1024 bytes, in the non-jumbo
frame case, and splitting the packets across multiple mbufs.
Consequently the above problem exposed another issue, which is when
packets were splitted across multiple mbufs, and all of the mbufs in the
chain have the M_PKTHDR flag set.
Submitted by: original patch by Ray Ruvinskiy at BlueCoat dot com
Reviewed by: jfv, kmacy, rwatson
Approved by: re (rwatson)
MFC after: 5 days
is retrieved after a failed SCSI command to continue normal
operation. Else this sense information is retrived at the next
SCSI command.
Approved by: re (kib)
Reported by: Alex Kozlov
MFC after: 1 week
PR: usb/160299
which does not support the no synchronize cache SCSI command.
The __FreeBSD_version version macro has been bumped and
external kernel modules needs to be recompiled after
this patch.
Approved by: re (kib)
MFC after: 1 week
PR: usb/160299
- tjmax - Tj(max) value from the CPU
- delta - current delta reading
- resolution - sensor resolution in Celsius
- throttle_log - whether a #PROCHOT was asserted since last reset
Submitted by: Mark Johnston <markjdb gmail.com> (mostly)
MFC after: 1 month
Approved by: re (kib)
keyboards allow console break sequences (such as ctrl-alt-esc) to be
entered, alternative break can prove useful under virtualisation and
remote console systems where entering control sequences can be
difficult or unreliable.
MFC after: 3 weeks
Approved by: re (bz)
improvements:
(1) Implement new model in previously missed at91 UART driver
(2) Move BREAK_TO_DEBUGGER and ALT_BREAK_TO_DEBUGGER from opt_comconsole.h
to opt_kdb.h (spotted by np)
(3) Garbage collect now-unused opt_comconsole.h
MFC after: 3 weeks
Approved by: re (bz)
accessible:
(1) Always compile in support for breaking into the debugger if options
KDB is present in the kernel.
(2) Disable both by default, but allow them to be enabled via tunables
and sysctls debug.kdb.break_to_debugger and
debug.kdb.alt_break_to_debugger.
(3) options BREAK_TO_DEBUGGER and options ALT_BREAK_TO_DEBUGGER continue
to behave as before -- only now instead of compiling in
break-to-debugger support, they change the default values of the
above sysctls to enable those features by default. Current kernel
configurations should, therefore, continue to behave as expected.
(4) Migrate alternative break-to-debugger state machine logic out of
individual device drivers into centralised KDB code. This has a
number of upsides, but also one downside: it's now tricky to release
sio spin locks when entering the debugger, so we don't. However,
similar logic does not exist in other device drivers, including uart.
(5) dcons requires some special handling; unlike other console types, it
allows overriding KDB's own debugger selection, so we need a new
interface to KDB to allow that to work.
GENERIC kernels in -CURRENT will now support break-to-debugger as long as
appropriate boot/run-time options are set, which should improve the
debuggability of BETA kernels significantly.
MFC after: 3 weeks
Reviewed by: kib, nwhitehorn
Approved by: re (bz)
The AR5212 HAL didn't check this field; timers are enabled a different
way.
The AR5416 HAL however did, and since this field was uninitialised, it had
whatever was on the stack at the time. This lead to "unpredictable"
behaviour.
This allows TDMA to work on the AR5416 and later chipsets.
Thanks to: paradyse@gmail.com
Approved by: re (kib, blanket)
* Fix SLEEP1/SLEEP2 register definitions; the CAB/Beacon timeout
fields have changed in AR5416 and later
* The TIM_PERIOD and DTIM_PERIOD registers are now microsecond fields,
not TU.
Obtained from: Linux ath9k, Atheros reference
Approved by: re (kib, blanket)
or later. Previous hardware had some as TU, some as 1/8th
TU.
* Modify AR_NEXT_DBA and AR_NEXT_SWBA to use a new macro,
ONE_EIGHTH_TU_TO_USEC(), which converts the 1/8th TU
fields to USEC. This is just cosmetic and matches the
Atheros reference driver.
* Fix AR_NEXT_TBTT, which is USEC, not TU.
Submitted by: paradyse@gmail.com
Approved by: re (kib, blanket)
programming secret. The PHY would go into sleep state when it
detects no established link and it will re-establish link when the
cable is plugged in. Previously it failed to re-establish link
when the cable is plugged in such that it required to manually down
and up the interface again to make it work. This came from
incorrectly programmed hibernation parameters. According to
Atheros, each PHY chip requires different configuration for
hibernation and different vendor has different settings for the
same chip.
Disabling hibernation may consume more power but establishing link
looks more important than saving power.
Special thanks to Atheros for giving me instructions that disable
hibernation.
MFC after: 1 week
Approved by: re (kib)
isolated but also powered down after a reset and while they just work fine
[sic] when both is the case they don't if they are only deisolate but still
powered down. So in order to put PHYs in an overall normal operation mode
for the common case, ensure in mii_phy_reset() that they are not powered
down after a reset. Unfortunately, this only helps in case of BCM5421,
while BCM5709S apparently only work when they remain isolated and powered
down after a reset. So don't call mii_phy_reset() in brgphy_reset() and
implement the reset locally leaving the problematic bits alone. Effectively
this bypasses r221812 for brgphy(4).
Thanks to Justin Hibbits for doing a binary search in order to identify
the problematic commit.
PR: 157405, 158156
Reviewed by: yongari (mii_phy_reset() part)
Approved by: re (kib)
MFC after: 3 days
cores with temp in the range 101-105 have been found in the past.
Sponsored by: Sandvine Incorporated
Reviewed by: delphij, emaste
Approved by: re (kib)
MFC after: 3 days
avoid lost timer interrupts. Previous optimization attempt doing it only
for intervals less then 5000 ticks (~300us) reported to be unreliable by
some people. Probably because of some heavy SMI code on their boards.
Introduce additional safety interval of 128 counter ticks (~9us) between
programmed comparator and counter values to cover different cases of
delayed write found on some chipsets.
Approved by: re (kib)
to implement fchown(2) and fchmod(2) support for several file types
that previously lacked it. Add MAC entries for chown/chmod done on
posix shared memory and (old) in-kernel posix semaphores.
Based on the submission by: glebius
Reviewed by: rwatson
Approved by: re (bz)
mutex, which would lead to a deadlock.
Many thanks to Areca for their continued support of FreeBSD.
Submitted by: Ching Huang <ching2048 areca com tw>
Tested by: Willem Jan Withagen <wjw digiware nl>
MFC after: 3 days
Approved by: re (kib)
