Previously, these cards were supported by the lnc driver (and they
still are, but the pcn driver will claim them first), which is fine
except the lnc driver runs them in 16-bit LANCE compatibility mode.
The pcn driver runs these chips in 32-bit mode and uses the RX alignment
feature to achieve zero-copy receive. (Which puts it in the same
class as the xl, fxp and tl chipsets.) This driver is also MI, so it
will work on the x86 and alpha platforms. (The lnc driver is still
needed to support non-PCI cards. At some point, I'll need to newbusify
it so that it too will me MI.)
The Am79c978 HomePNA adapter is also supported.
other schedsoft*() functions since they have never been used.
Removed confused comment about not needing these functions. The
functions delay scheduling of SWIs until the next hardclock tick.
For devices that only deliver a few characters per interrupt, this
reduces the number of calls to the scheduler by a large factor (about
115 for each sio port at 115200 bps).
thread for each interrupt that comes in. If we don't, log the event and
return immediately for a hardware interrupt. For a softinterrupt, panic
instead.
Submitted by: ben
The code for suspend/resume is derived from APM device driver.
Some people suggested the original code is somewhat buggy, but I'd
like to just move it from apm.c without any major changes for the
initial version. This code should be refined later.
To use pmtimer to adjust time at resume time, add
device pmtimer
in your kernel config file, and add
hint.pmtimer.0.at="isa"
in your device.hints
Reviewed by: -current, bde
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
in the boot. The cleanup must be done in one of the few ways that
db_numargs() understands, so that early backtraces in ddb don't underrun
the stack. The underruns caused reboots a few years ago when there
was an unmapped page above the stack (trapping to abort the command
doesn't work early).
Cleaned up some nearby code.
curproc was initialized. curproc == NULL was interpreted as matching
the process holding Giant... Just skip mtx_enter() and mtx_exit() in
trap() if (curproc == NULL && cold) (&& cold for safety).
don't take an arg, but swi_generic() is special in order to avoid one
whole conditional branch in the old SWI dispatch code. The new SWI
dispatch code passed it a garbage arg. Bypass swi_generic() and call
swi_dispatcher() directly, like the corresponding alpha code has always
done.
The panic was rare because because it only occurred if more than one
of the {sio,cy,rc} drivers was configured and one was active, and the
cy driver doesn't even compile.
macros that expand to pass filename and line number information. This is
necessary since we're using inline functions instead of macros now.
Add const to the filename pointers passed througout the mtx and witness
code.
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
