These devices should be probed first because they are at fixed
locations and cannot be turned off. ISA PNP devices, on the other
hand, can be turned off and often can be flexible in the resources
they use. Probe them last, as always.
eg. if the firmware load fails. Shortish MFC timeout so this can be merged
before the 4.11 freeze.
PR: kern/34306
Submitted by: gibbs
Approved by: gibbs, imp (mentor)
MFC after: 5 days
zero-copy receive of jumbo frames. This eliminates the need for the
jumbo frame allocator implemented in kern/uipc_jumbo.c and sys/jumbo.h.
Remove it.
Note: Zero-copy receive of jumbo frames did not work without these changes;
I believe there was insufficient locking on the jumbo vm object.
Tested by: ken@
Discussed with: gallatin@
properly support bounce buffers and resource shortages. This allows the
driver to work properly and reliably with more than 4GB of RAM. Of the
three data paths that exist in the driver, (block, CAM, ioctl), the ioctl
path has not been well tested with these changes due to difficulty with
finding an application that uses it that actually works.
Sponsored by: The FreeBSD Foundation and FreeBSD Systems, Inc.
If we are resuming non-MPSAFE drivers, they need Giant held for them.
This may fix some obscure suspend/resume problems. It has fixed keyrate
setting problems that were triggered by cardbus (MPSAFE) changing the
ordering for syscons resume (non-MPSAFE). Also, add some asserts that
Giant is held in our suspend/resume and shutdown methods.
Found by: iedowse
MFC after: 2 days
non-standard BIOSen. We used to implement this in local patches but
now that ACPI-CA has merged/re-implemented most of our fixes, they were
no longer needed and we just needed to turn this knob on. Also, remove
an unnecessary cast.
Tested by: phk
we really want vs. the size changing 'long' (i386 vs. AMD64).
This fixes the problem with DRM with Radeon's on AMD64.
Submitted by: Jung-uk Kim <jkim@niksun.com>
back on again in resume. Override the default of D3 with the value the
BIOS specifies in _SxD, if present. Skip serial devices (PNP05xx) since
they seem to hang when set to D3 and may require special driver support.
Also, skip non-type 0 PCI devices (i.e., bridges) since our we don't yet
save/restore their config space and that seems to be necessary.
If this gives you trouble with suspend/resume, you can disable the new
ACPI and PCI power behavior separately with these tunables & sysctls:
debug.acpi.do_powerstate
hw.pci.do_powerstate
Approved by: imp (pci)
Tested by: acpi@ (numerous)
in the _PRS or _CRS of link devices. If faced with multiple DPFs in a
_PRS, we just use the first one. We assume that if _CRS has DPF tags they
only contain a single set since multiple DPFs wouldn't make any sense. In
practice, the only DPFs I've seen so far for link devices are that the one
IRQ resource is surrounded by a DPF tag pair for no apparent reason, and
this should handle that case fine now.
- Only allocate link structures for IRQ resources for link devices rather
than allocating a link structure for every resource.
Reviewed by: njl
Tested by: phk
@sys/dev/acpica/acpi_pci_link.c:153" panic by backing out rev 1.37 in the SMP
case. It appears that on a dual-proc machine the assertions in the rev 1.37
commit log hold true.
resource lists. It used to be sized based only on _CRS, hence _PRS could
perform an out-of-bounds access if it was larger (i.e., when there are
dependent functions). Add asserts to detect this case. Note, this is
only a temporary fix and I believe _PRS and _CRS should have separate
arrays.
Also, fix a typo where the wrong irq was being check for the APIC case.
Submitted by: tegge
the address of a channel on a SCC, it returns 0 on failure. [1]
- Hardcode channel 1 for the keyboard on Z8530, the information present
in the Open Firmware device tree doesn't allow to determine this via
uart_cpu_channel(). This makes the keyboard (if one backs out rev. 1.5
of sys/dev/puc/puc_sbus.c and has both keyboard and mouse plugged in to
avoid the hang that revision works around) and consequently syscons(4)
on Ultra 2 work. There's a problem with the keyboard LEDs similar to
the one on Ultra 60 (LEDs don't get lit under X) though, instead of
lighting just a specific single one all get lit and can't be turned off
again. [1]
- Add comments about what uart_cpu_channel() and uart_cpu_getdev_keyboard()
do and their constraints.
- Improve the comments about what uart_cpu_getdev_[console,dbgport]() do,
they don't return an address (as in bus) but an Open Firmware package
handle.
Reviewed by: marcel (modulo the comments) [1]
NetBSD got activated. NetBSD has an additional change in
their mii.c rev 1.26 which got missed with that merger:
: When probing for a PHY, look at the EXTSTAT bit in the BMSR, as well,
: not just the media mask. This prevents PHYs/TBIs that only support
: Gigabit media from slipping through the cracks.
With this GE only ones like from the SK-9844 are detected again.
PR: i386/63313, i386/71733, kern/73725
Tested by: matt baker <matt at sevenone dot com>, Jin Guojun <jin at george dot lbl dot gov>
Approved by: rwatson (mentor)
Obtained from: NetBSD mii.c rev 1.26
MFC after: 1 week
- Use a new-bus device driver for the ACPI PCI link devices. The devices
are called pci_linkX. The driver includes suspend/resume support so that
the ACPI bridge drivers no longer have to poke the links to get them
to handle suspend/resume. Also, the code to handle which IRQs a link is
routed to and choosing an IRQ when a link is not already routed is all
contained in the link driver. The PCI bridge drivers now ask the link
driver which IRQ to use once they determine that a _PRT entry does not
use a hardwired interrupt number.
- The new link driver includes support for multiple IRQ resources per
link device as well as preserving any non-IRQ resources when adjusting
the IRQ that a link is routed to.
- The entire approach to routing when using a link device is now
link-centric rather than pci bus/device/pin specific. Thus, when
using a tunable to override the default IRQ settings, one now uses
a single tunable to route an entire link rather than routing a single
device that uses the link (which has great foot-shooting potential if
the user tries to route the same link to two different IRQs using two
different pci bus/device/pin hints). For example, to adjust the IRQ
that \_SB_.LNKA uses, one would set 'hw.pci.link.LNKA.irq=10' from the
loader.
- As a side effect of having the link driver, unused link devices will now
be disabled when they are probed.
- The algorithm for choosing an IRQ for a link that doesn't already have an
IRQ assigned is now much closer to the one used in $PIR routing. When a
link is routed via an ISA IRQ, only known-good IRQs that the BIOS has
already used are used for routing instead of using probabilities to
guess at which IRQs are probably not used by an ISA device. One change
from $PIR is that the SCI is always considered a viable ISA IRQ, so that
if the BIOS does not setup any IRQs the kernel will degenerate to routing
all interrupts over the SCI. For non ISA IRQs, interrupts are picked
from the possible pool using a simplistic weighting algorithm.
Tested by: ru, scottl, others on acpi@
Reviewed by: njl
- Let hme_start()/hme_init() acquire lock and then call
hme_start_locked()/hme_init_locked() respectivly.
- Teardown interrupt handler before hme_detach().
- Remove IFF_NEEDSGIANT flag and mark interrupt handler INTR_MPSAFE.
- Set callout handler to CALLOUT_MPSAFE.
- Add locks in hme MII interface.
Reviewed by: jake
Tested by: Julian C. Dunn <jdunn at opentrend dot net>
MFC after: 2 weeks
not used and aliases for other defines.
o Add REG_DATA as an alias for com_data. Likewise for other register
defines.
o Add LCR_SBREAK and make CFCR_SBREAK an alias for it. Likewise for
the other LCR register bits that are known with the CFCR prefix.
o Add MCR_IE and make MCR_IENABLE an alias for it.
o Add LSR_TEMT and make LSR_TSRE an alias for it.
o Add LSR_THRE and make LSR_TXRDY as alias for it.
o Add FCR_ENABLE and make FIFO_ENABLE as alias for it. Likewise for
the other FCR register bits that are known with the FIFO prefix.
o Add EFR_CTS and make EFR_AUTOCTS an alias for it.
o Add EFR_RTS and make EFR_AUTORTS an alias for it.
This is a first step in cleaning up the definitions in this file.
to us was to help out the Linux port, but really just invited overflow.
In fact, the request sense timer was overflowing prior to this change making
it much shorter than intended.
aic_osm_lib.h:
Be more careful about overflow in all timer/timeout primitives.
queue a packet to the hardware... instead of when the hardware queue is
empty..
don't initalize cur_tx now that it doesn't need to be...
Pointed out by: bde
respective NetBSD driver for use with the genclock interface.
It's first use will be on sparc64 but it was also tested on alpha with
a preliminary patch to switch alpha to use the genclock code together
with this driver instead of the respective code in alpha/alpha/clock.c
and the rather MD mcclock(4). Using it on i386 and amd64 won't be that
hard but some changes/extensions to improve the genclock code in general
should be done first, e.g. add locking and make it easier to access the
NVRAM usually coupled with RTCs.
