warnx()+exit() with errx() and replace a big if..then..else construct
to determine the package download directory with a lookup table.
Reviewed by: jkh
MFC after: 2 weeks
/usr/share/syscons/keymaps. This should prevent word breakage when new keymaps
have been added.
Prompted by: Matthew D. Fuller <fullermd@over-yonder.net>
TLU event handler).
This used to be done as a side effect of SIOCAIFADDR'ing the interface,
but now that duplicate SIOCAIFADDRs are optimised out, we can't depend
on that behaviour.
and DP83821 gigabit ethernet MAC chips and the NatSemi DP83861 10/100/1000
copper PHY. There are a whole bunch of very low cost cards available with
this chipset selling for $150USD or less. This includes the SMC9462TX,
D-Link DGE-500T, Asante GigaNIX 1000TA and 1000TPC, and a couple cards
from Addtron.
This chip supports TCP/IP checksum offload, VLAN tagging/insertion.
2048-bit multicast filter, jumbograms and has 8K TX and 32K RX FIFOs.
I have not done serious performance testing with this driver. I know
it works, and I want it under CVS control so I can keep tabs on it.
Note that there's no serious mutex stuff in here yet either: I need
to talk more with jhb to figure out the right way to do this. That
said, I don't think there will be any problems.
This driver should also work on the alpha. It's not turned on in
GENERIC.
- check the msg.tsp_type value prior to using it as an
index into char *tsptype[]
- use strlcpy's instead of strcpy's
- & handle short packets properly.
Submitted by: "Andrew R. Reiter" <arr@watson.org>
Obtained from: OpenBSD
block sizes.
This orginally worked in PAO-3 and worked on their r330 branch but got
broken in PAO-3 around December 1998!
Approved by: imp
Obtained from: PAO-3
creation.
* Tag the internal err() function with __printflike to allow checking
for non-constant format string arguments (none exist)
* Use fmtcheck() to sanitize the tar command obtained via -t to make
sure it doesn't contain extraneous format operators.
Reviewed by: mikeh
MFC after: 1 week
longer includes machine/elf.h.
* consumers of elf.h now use the minimalist elf header possible.
This change is motivated by Binutils 2.11.0 and too much clashing over
our base elf headers and the Binutils elf headers.
of a/x -> b and then negotiate a/x -> c by simply expecting SIOCAIFADDR
to do the change.
This was broken by the last commit that optimised out the deletion and
re-addition of the same a/x -> b combination, and forgot to compare
the old/new destination addresses.
Conveniently enough, this problem didn't effect setups where the
default route goes via the ppp link, and most other setups don't
care what the the destination address is actually set to. It broke
test environments where ppp connects to the local machine rather
badly though....
account at creation, create accounts with a "*" password (so you can
use alternate authentication schemes without fearing a "default" password
biting you later), and blank passwords.
Yes, adduser could create a blank password account, but this makes it
slightly more difficult to shoot yourself in the foot.
The /etc/adduser.conf entries are:
# use password-based authentication for new users
# defaultusepassword = "yes" | "no"
defaultusepassword = "yes"
# enable account password at creation
# (the password will be prepended with a star if the account isn't enabled)
# defaultenableaccount = "yes" | "no"
defaultenableaccount = "yes"
# allow blank passwords
# defaultemptypassword = "yes" | "no"
defaultemptypassword = "no"
Requested by: alfred
Reviewed by: alfred
valid keyword handling and the holiday file processing
- don't issue a warning in case the holiday file is not found
- enable inclusion of ../Makefile.inc to reenable compiling-in monitor
support into isdnd
- update manual page, add a comma and correct authors mail address
This driver supports PCI Xr-based and ISA Xem Digiboard cards.
dgm will go away soon if there are no problems reported. For now,
configuring dgm into your kernel warns that you should be using
digi. This driver is probably close to supporting Xi, Xe and Xeve
cards, but I wouldn't expect them to work properly (hardware
donations welcome).
The digi_* pseudo-drivers are not drivers themselves but contain
the BIOS and FEP/OS binaries for various digiboard cards and are
auto-loaded and auto-unloaded by the digi driver at initialisation
time. They *may* be configured into the kernel, but waste a lot
of space if they are. They're intended to be left as modules.
The digictl program is (mainly) used to re-initialise cards that
have external port modules attached such as the PC/Xem.
after the port build/install. The former cleans up "dirty" port work
directories that happen to be lying around, and the latter cleans up
after we're done so that they won't trip up someone else.
PR: ports/25106
Submitted by: tim@bishnet.net, nik, mwm@mired.org
extensive pass through the rpcbind code soon, but I might as well
bring these in now.
- (NetBSD util.c r1.5) Move the initialisation of `tbuf' to avoid
a case where it could end up containing junk from the stack. This
should address the issue in PR bin/26806.
- (NetBSD util.c r1.6) Don't `merge' AF_LOCAL addresses, fix a few
memory leaks.
PR: bin/26806
Submitted by: Martin Blapp <mb@imp.ch>
Obtained from: NetBSD
/usr/X11R6/bin should be there. This helps all the ports that need to
run `mkfontdir' and error out as many port maintainers do not realize
`mkfontdir' isn't in the path.
Prompted by: pkg_add pcemu
make the code not automatically dead but actually use the debug level
in order to determine if output is needed. Fix non-existant from_addr()
by #define'ing it to inet_ntoa().
Remove hardcoded -g from Makefile.
Reported by: "John W. De Boskey" <jwd@bsdwins.com>
Tested by: "John W. De Boskey" <jwd@bsdwins.com>
