Fill in some formerly NULL members where the implementation function
exists. Add a dummy function that panics and use it as a placeholder
for thigns that are still unimplemented. Remove a few unused includes.
every operation to retrieve the bs_cookie value almost nothing actually uses.
The bus_space struct contains a private data pointer (poorly named bs_cookie,
now renamed to bs_privdata) which is used only by a few old armv4 xscale
implementations. The bus_space functions were all defined to take this
value as the first parameter instead of the bus_space_tag_t, requiring all
the inline macro and function expansions to dereference the tag to pass it
to another function, which never uses it. Now all the functions take the tag
as the first parameter and retrieve the privdata if they need it.
Also fix a couple bus_space_unmap() implementations that were calling
kva_free() instead of pmap_unmapdev().
Discussed with: cognet
driver on Rockchip boards. It currently supports PIO mode
and dma mode needs external dma controller to be used.
Submitted by: jmcneill
Approved by: stas (mentor)
This doesn't actually change any behavior, because it just allows a 16-bit
read of the command register to return the correct value, and nothing
actually does a 16-bit read of that register.
sdhci controllers, such as the one on a Raspberry Pi, mishandle the signal
timing in high speed signaling mode, but run just fine in standard mode
with the bus running at frequencies between 25-50MHz (which shouldn't work).
This is the solution adopted by U-Boot and other OSes (linux and *BSD)
for the timeouts on Raspberry Pi boards with certain SD cards. Some
research shows that this quirk is also used on a few other boards, so the
fix is a generic quirk instead of being in the RPi-specific driver code.
This change is based on information discovered by Michal Meloun.
the stack for secondary cores, the other two values are only used for zeroing
bss on the primary core. No need to store the size of the stack at the
top of the stack (seems to be a leftover instruction from some cut-n-paste).
While in theory this should have been a transparent change (and was for all
other drivers), cpsw(4) never used the proper accessor macros in a few
places but spelt the indirect m_hdr.mh_* out itself. Convert those to
use m_len and m_data and unbreak the driver build.
To cut off the power we need to start the shutdown sequence by writing
the OFF bit on PMIC.
Once the PMIC is programmed the SoC needs to toggle the PMIC_PWR_ENABLE
pin when it is ready for the PMIC to cut off the power. This is done by
triggering the ALARM2 interrupt on SoC RTC.
The RTC driver only works in power management mode which means it won't
provide any kind of time keeping functionality. It only implements a way
to trigger the ALARM2 interrupt when requested.
Differential Revision: https://reviews.freebsd.org/D1489
Reviewed by: rpaulo
MFC after: 2 weeks
The driver inherently does dma in 512 byte chunks, but it's possible that
such a buffer can span two physically discontiguous pages (such as when
a userland program does IO on the raw /dev/mmcsdN devices). Now the driver
can handle a buffer that's split across two pages.
It could in theory handle any number of segments now, but as long as IO is
being done in 512 byte blocks it will never need more than two.
requires that each 512 byte IO be in a single contiguous buffer, but if a
buffer crosses a page boundary and the physical pages aren't contiguous
you can get an EFBIG failure (too many segments).
The driver really should handle multiple segment IO, but before adding that
I wanted to make sure that it's handling failure properly while the failure
is easily recreatable.
that some #ifdef SMP code is also conditional on __ARM_ARCH >= 7; we don't
support SMP on armv6, but some drivers and modules are compiled with it
forced on via the compiler command line.
For this to work the driver needs to know the bank it has attached to since
the registers for the first 12 pins are at a different location.
Move the lock initialization to simplify the code.
isn't supposed to manage all the GPIO pins in the system from a single
instance, instead it will attach to each one of the four available GPIO
controllers and only deal with one bank at time (32 pins per bank).
Rework part of the driver to take advantage of that, this simplify the
code a lot.
Also fix a bug in rk30_gpio_get_function() which wouldn't return the
correct values.
While here fix a typo in register name.
code in sys/kern/kern_dump.c. Most dumpsys() implementations are nearly
identical and simply redefine a number of constants and helper subroutines;
a generic implementation will make it easier to implement features around
kernel core dumps. This change does not alter any minidump code and should
have no functional impact.
PR: 193873
Differential Revision: https://reviews.freebsd.org/D904
Submitted by: Conrad Meyer <conrad.meyer@isilon.com>
Reviewed by: jhibbits (earlier version)
Sponsored by: EMC / Isilon Storage Division
