This largely reuses the TLS TOE support added in r330884. However,
this uses the KTLS framework in upstream OpenSSL rather than requiring
Chelsio-specific patches to OpenSSL. As with the existing TLS TOE
support, use of RX offload requires setting the tls_rx_ports sysctl.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24453
- Add a new TCP_RXTLS_ENABLE socket option to set the encryption and
authentication algorithms and keys as well as the initial sequence
number.
- When reading from a socket using KTLS receive, applications must use
recvmsg(). Each successful call to recvmsg() will return a single
TLS record. A new TCP control message, TLS_GET_RECORD, will contain
the TLS record header of the decrypted record. The regular message
buffer passed to recvmsg() will receive the decrypted payload. This
is similar to the interface used by Linux's KTLS RX except that
Linux does not return the full TLS header in the control message.
- Add plumbing to the TOE KTLS interface to request either transmit
or receive KTLS sessions.
- When a socket is using receive KTLS, redirect reads from
soreceive_stream() into soreceive_generic().
- Note that this interface is currently only defined for TLS 1.1 and
1.2, though I believe we will be able to reuse the same interface
and structures for 1.3.
Instead, copy the strings into a temporary buffer on the stack and
run strcmp on the copies.
Reviewed by: brooks, kib
Obtained from: CheriBSD
MFC after: 1 week
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24567
Some models of laptops e.g. "X1 Carbon 3rd Gen Thinkpad" have LRM buttons
wired as so called "Synaptic touchpads extended buttons" rather thah real
trackpoint buttons. Handle this case with merging of events from both
sources.
PR: 245877
Reported by: Raichoo <raichoo@googlemail.com>
MFC after: 1 week
Kernel prints the device announcement before the attach method is
called, so if the correct description is not set by the probe method,
then the announcement would have an incorrect one.
MFC after: 1 week
Use DRIVER_MODULE_ORDERED(SI_ORDER_ANY) so that ig4's ACPI attachment
happens after iicbus and acpi_iicbus drivers are registered.
I have seen a problem where iicbus attached under ig4 instead of
acpi_iicbus when ig4.ko was loaded with kldload. I believe that that
happened because ig4 driver was a first driver to register, it attached
and created an iicbus child. Then iicbus driver was registered and,
since it was the only driver that could attach to the iicbus child
device, it did exactly that. After that acpi_iicbus driver was
registered. It would be able to attach to the iicbus device, but it was
already attached, so nothing happened.
MFC after: 2 weeks
In r360131, acpi_ec probe was changed to not clobber an error status prior to
several error cases that did not explicitly set the error variable before
goto'ing the exit path. However, I did not notice that the error variable was
not set to success in the success path. That caused all successful probes to
fail, which is obviously undesirable.
PR: 245778
Reported by: Neel Chauhan <neel AT neelc.org>, Evilham <contact AT evilham.com>
Tested by: Evilham
X-MFC-With: r360131
as the dma_device during RDMA registration.
cxgbe's struct device cannot be used as-is because it's a native FreeBSD
driver and ibcore is LinuxKPI based.
MFC after: 1 week
MFC after: r360196
The sole in-tree user of this flag has been retired, so remove this
complexity from all drivers. While here, add a helper routine drivers
can use to read the current request's IV into a local buffer. Use
this routine to replace duplicated code in nearly all drivers.
Reviewed by: cem
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D24450
In r360126, I meant to have a different mask only on powerpc, not powerpc64.
Update the check to check that we're not compiling for powerpc64.
Reported by: jhibbits
Approved by: wulf (implicit)
MFC after: 2 weeks
X-MFC-Note: 12 only
X-MFC-With: r360126
Differential Revision: D24370 (followup)
All of the 'goto out;' cases in this probe routine without explicit
initialization of 'ret' indicate error cases and were clearly intended
to use the initial definition of 'ret' with ENXIO. However, 'ret' was
accidentally squashed by reuse for a subroutine call near the beginning
of probe.
Use a different variable for the subroutine status to preserve ENXIO ret
for the 'goto out's as a minimal solution to the panic reported at attach
for now.
PR: 245757
Change kern.evdev.rcpt_mask from 3 to 12 by default. This makes us much
more evdev-friendly, and will prevent everyone using xorg and wayland with
evdev devices (the default) from needing to change this locally.
powerpc32 still uses the old value for the keyboard part, becaues the adb
keyboard driver used there is not evdev compatible.
Reviewed by: wulf
Approved by: wulf
MFC after: 2 weeks
X-MFC-Note: 12 only
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D24370
elements in the middle.
This fixes a panic when detaching USB mouse.
PR: 245732
Reviewed by: wulf
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D24500
don't implement link power management, LPM.
This fixes error code XHCI_TRB_ERROR_BANDWIDTH for isochronous USB 3.0
transactions.
Submitted by: Horse Ma <Shichun.Ma@dell.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
snd_hda was rewritten in r230130; one function retained a comment
referencing the previous name.
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
A later change, currently being iterated on in D24459, will in-fact change
the lock type to an sx so that TTY drivers can sleep on it if they need to.
Committing this ahead of time to make the review in question a little more
palatable.
tty_lock_assert() is unfortunately still needed for now in two places to
make sure that the tty lock has not been recursed upon, for those scenarios
where it's supplied by the TTY driver and possibly a mutex that is allowed
to recurse.
Suggested by: markj
On my Dell Latitude 7390 laptop, the brightness hotkeys
(Fn+<up/down arrow>) send ACPI notifications which acpi_video
handles by adjusting its brightness setting; but ACPI does not
actually do anything with the backlight.
Announcing brightness changes via devd makes it possible to close
the loop by triggering the intel_backlight utility to perform the
required backlight adjustment.
Reviewed by: imp
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D24424
Name each ehci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ehci from kernel; already loaded from kernel
A similar fix was done in r333074 but imx_ehci wasn't renamed and generic_ehci wasn't
present at that time.
KTLS uses the flowid to distribute software encryption tasks among its
pool of worker threads. Without this change, all software KTLS
requests for TOE sockets ended up on the first worker thread.
Note that the flowid for TOE sockets created via connect() is not a
hash of the 4-tuple, but is instead the id of the TOE pcb (tid). The
flowid of TOE sockets created from TOE listen sockets do use the
4-tuple RSS hash as the flowid since the firmware provides the hash in
the message containing the original SYN.
Reviewed by: np (earlier version)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24348
This fixes a panic when unloading and reloading t4_tom.ko since the
old pointer is still stored when t4_tom_load tries to set it.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24358
This pattern is used in callbacks with void * data arguments and seems
both relatively uncommon and relatively harmless. Silence the warning
by casting through uintptr_t.
This warning is on by default in Clang 11.
Reviewed by: arichardson
Obtained from: CheriBSD (partial)
MFC after: 1 week
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24425
If the fdt node doesn't have a cd-gpios properties or if the node is set
as non-removable we do not init the card detection timeout task as it is
useless so don't schedule it too.
MFC after: 1 month
X-MFC-With: r359924
This fixes a panic that would occur when the timer tried to close a
stale socket.
Submitted by: Krishnamraju Eraparaju @ Chelsio
MFC after: 1 week
Sponsored by: Chelsio Communications
Copy the CP, PTRIN, etc macros from freebsd32.h into a sys/abi_compat.h
and replace existing definitation with includes where required. This
eliminates duplicate code and allows Linux and FreeBSD compatability
headers to be included in the same files.
Input from: cem, jhb
Obtained from: CheriBSD
MFC after: 2 weeks
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24275
the dts to find the supported speeds and the regulators.
Not all DTS have every settings properly defined so host controller
will still have to add some caps themselves.
It also add a mmc_fdt_gpio_setup function which will read the cd-gpios
property and register it as the CD pin.
If the pin support interrupts one will be registered and the cd_helper
function will be called.
If the pin doesn't support interrupts the internal taskqueue will poll
for change and call the same cd_helper function.
mmc_fdt_gpio_setup will also parse the wp-gpio property and MMC drivers
can know the write-protect pin value by calling the
mmc_fdt_gpio_get_readonly function.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23267
While the original implementation of unmapped mbufs was a large
step forward in terms of reducing cache misses by enabling mbufs
to carry more than a single page for sendfile, they are rather
cache unfriendly when accessing the ext_pgs metadata and
data. This is because the ext_pgs part of the mbuf is allocated
separately, and almost guaranteed to be cold in cache.
This change takes advantage of the fact that unmapped mbufs
are never used at the same time as pkthdr mbufs. Given this
fact, we can overlap the ext_pgs metadata with the mbuf
pkthdr, and carry the ext_pgs meta directly in the mbuf itself.
Similarly, we can carry the ext_pgs data (TLS hdr/trailer/array
of pages) directly after the existing m_ext.
In order to be able to carry 5 pages (which is the minimum
required for a 16K TLS record which is not perfectly aligned) on
LP64, I've had to steal ext_arg2. The only user of this in the
xmit path is sendfile, and I've adjusted it to use arg1 when
using unmapped mbufs.
This change is almost entirely mechanical, except that we
change mb_alloc_ext_pgs() to no longer allow allocating
pkthdrs, the change to avoid ext_arg2 as mentioned above,
and the removal of the ext_pgs zone,
This change saves roughly 2% "raw" CPU (~59% -> 57%), or over
3% "scaled" CPU on a Netflix 100% software kTLS workload at
90+ Gb/s on Broadwell Xeons.
In a follow-on commit, I plan to remove some hacks to avoid
access ext_pgs fields of mbufs, since they will now be in
cache.
Many thanks to glebius for helping to make this better in
the Netflix tree.
Reviewed by: hselasky, jhb, rrs, glebius (early version)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D24213
