signal to the master nfsd daemon whenever the stable restart
file has been modified. This will allow the master nfsd daemon
to maintain an up to date backup copy of the file. This is
enabled via the nfssvc() syscall, so that older nfsd daemons
will not be signaled.
Reviewed by: jhb
MFC after: 1 week
besides the duplex ones set so just comparing it with IFM_FDX may lead
to false negatives.
- Just let the default case handle all unsupported media types.
- In pnphy_status() don't unnecessarily read a register twice.
- Remove unnused macros.
MFC after: 1 week
configuration, which is used to work around issues with certain setups
(see r161237) by default, should not be triggered as it may in turn
cause harm in some edge cases.
- Even after masking the media with IFM_GMASK the result may have bits
besides the duplex ones set so just comparing it with IFM_FDX may lead
to false negatives.
- Announce PAUSE support also for manually selected 1000BASE-T, but for
all manually selected media types only in full-duplex mode. Announce
asymmetric PAUSE support only for manually selected 1000BASE-T.
- Simplify setting the manual configuration bits to only once after we
have figured them all out. This also means we no longer unnecessarily
update the hardware along the road.
- Remove a stale comment.
Reviewed by: yongari (plus additional testing)
MFC after: 3 days
besides the duplex ones set so just comparing it with IFM_FDX may lead
to false negatives.
- Simplify ciphy_service() to only set the manual configuration bits
once after we have figured them all out. This also means we no longer
unnecessarily update the hardware along the road.
MFC after: 1 week
complicates the code.
- Don't let atphy_setmedia() announce PAUSE support for half-duplex when
MIIF_FORCEPAUSE is set.
- Simplify e1000phy_service() and ip1000phy_service() to only set the
manual configuration bits once after we have figured them all out. For
ip1000phy_service() this also means we no longer unnecessarily update
the hardware along the road.
MFC after: 1 week
- Move the realtime priority range up above kernel sleep priorities and
just below interrupt thread priorities.
- Contract the interrupt and kernel sleep priority ranges a bit so that
the timesharing priority band can be increased. The new timeshare range
is now slightly larger than the old realtime + timeshare ranges.
- Change the ULE scheduler to no longer use realtime priorities for
interactive threads. Instead, the larger timeshare range is now split
into separate subranges for interactive and non-interactive ("batch")
threads. The end result is that interactive threads and non-interactive
threads still use the same priority ranges as before, but realtime
threads now have a separate, dedicated priority range.
- Do not modify the priority of non-timeshare threads in sched_sleep()
or via cv_broadcastpri(). Realtime and idle priority threads will
no longer have their priorities affected by sleeping in the kernel.
Reviewed by: jeff
started to execute, it seems that the corresponding ISR bit in the "old"
local APIC can be cleared. This causes the local APIC interrupt routine
to fail to find an interrupt to service. Rather than panic'ing in this
case, simply return from the interrupt without sending an EOI to the
local APIC. If there are any other pending interrupts in other ISR
registers, the local APIC will assert a new interrupt.
Tested by: steve
In n32 and n64, add support for physical address above 4GB by having
64 bit page table entries and physical addresses. Major changes are:
- param.h: update PTE sizes, masks and shift values to support 64 bit PTEs.
- param.h: remove DELAY(), mips_btop(same as atop), mips_ptob (same as
ptoa), and reformat.
- param.h: remove casting to unsigned long in trunc_page and round_page
since this will be used on physical addresses.
- _types.h: have 64 bit __vm_paddr_t for n32.
- pte.h: update TLB LO0/1 access macros to support 64 bit PTE
- pte.h: assembly macros for PTE operations.
- proc.h: md_upte is now 64 bit for n32 and n64.
- exception.S and swtch.S: use the new PTE macros for PTE operations.
- cpufunc.h: TLB_LO0/1 registers are 64bit for n32 and n64.
- xlr_machdep.c: Add memory segments above 4GB to phys_avail[] as they are
supported now.
Reviewed by: jmallett (earlier version)
the lock instead of queueing it to a task.
- Do not invoke jme_rxintr() to reclaim any unprocessed but received
packets when shutting down the interface. Instead, just drop these
packets to match the behavior of other drivers.
- Hold the driver lock in the interrupt handler to avoid races with
ioctl requests to down the interface.
Reviewed by: yongari
interactive timeshare threads (PRI_*_INTERACTIVE) and non-interactive
timeshare threads (PRI_*_BATCH) and use these instead of PRI_*_REALTIME
and PRI_*_TIMESHARE. No functional change.
Reviewed by: jeff
1. Use vm_paddr_t for physical addresses.
There are a few places in the MIPS platform code where vm_offset_t is
used for physical addresses, change these to use vm_paddr_t:
- phys_avail[], physmem_desc[] arrays
- pmap_mapdev(), page_is_managed(), is_cacheable_mem() pmap_map() args
- local variables of various pmap functions
2. Change init_pte_prot() return from int to pt_entry_t, as this can be
64 bit when using 64 bit TLB entries.
3. Update printing of pt_entry_t and of vm_paddr_t to use 'j' format with
uintmax_t. This will be useful later if we plan to use 64bit phsical addr
on 32 bit n32 compilation.
Reviewed by: imp
bus_size_t may be 32 or 64 bits. Change the bounce_zone alignment field
to explicitly be 32 bits, as I can't really imagine a DMA device that
needs anything close to 2GB alignment of data.
packets.
*) Reject requests with a protocol length not equal to 4. This is IPv4
and there is no reason to accept anything else.
*) Reject packets that have a multicast source hardware address.
*) Drop requests where the hardware address length is not equal
to the hardware address length of the interface.
Pointed out by: Rozhuk Ivan
MFC after: 1 week
