For reasons which are not clear, r254263 broke some PCMCIA and CardBus
bridges in strange ways, either rendering them unable to detect
insertion and removal events, or possibly unable to read from the
device behind the bridge.
This fixes at least one laptop, a Toshiba Tecra M5 with a Texas
Instruments PCxx12 (d=0x8039 v=0c104c) bridge. The very similar
Tecra M9 has the same bridge, but worked fine without this change.
The bridge chip has no I/O port BAR, and there is nothing in the spec
to suggest I/O decoding should be enabled; however enabling it fixes
the issue. Add an XXX comment to this effect.
Discussed with: jhb, imp
- Nuke unused sdhci_softc.
- Static'ize sdhci_debug local to sdhci.c.
- Const'ify PCI device description strings.
- Nuke redundant resource ID members from sdhci_pci_softc.
- Nuke unused hw.sdhci_pci.debug tunable.
- Add support for using MSI instead of INTx, controllable via the tunable
hw.sdhci.enable_msi (defaulting to on) and tested with a RICOH R5CE823 SD
controller.
- Use NULL instead of 0 for pointers.
This fixes bad looking refresh when switching window: squares instead
of text, flashing screen, and so on. In the worst case, vt_flush() came
at a very inappropriate timing and the screen was not refreshed at all
(leaving squares all over the place).
This doesn't fix the flickering of the screen with vt_vga, because the
sync signal is temporarily stopped and the video memory is cleared.
Sponsored by: The FreeBSD Foundation
r270269:
vt(4): Handle global and per-window mouse cursor toggle in one place
Before the global flag was set/unset using the CONS_MOUSECTL ioctl,
and the per-window flag through the MOUSE_SETLEVEL or MOUSE_SETMODE
ioctls.
Also, if the cursor is already enabled/disabled, return immediatly.
This avoids to reset the cursor's position to the center of the
screen.
This matches syscons' behavior.
While here, remove a trailing space and a redundant variable
declaration.
r270271:
vt(4): Mark cursor old position as dirty before reading the dirty area
Otherwise, the redraw is done during the next vt_flush run.
r270272:
vt(4): If the cursor is globally disabled, don't mark its position as dirty
This avoids unnecessary redraw. In particular, during boot, where the
cursor is disabled and its fake position is [0;0], this triggered a
refresh of the whole screen each time vt_flush() is called.
r270273:
vt(4): If the cursor didn't move, don't mark its position as dirty
Currently, this has no effect, because the cursor is always redrawn
anyway. But this will be useful after improvements to the
vd_bitbltchr_t callback API.
The vt_device structure members used to store the position of the
cursor as of the last redraw are renamed from vd_mdirty{x,y} to
vd_mold{x,y}. The associated comment is fixed too. Also, their value
is now expressed in pixels, not in character columns/row.
r270275:
vt(4): Mark the current cursor position as dirty
Like r270273, this has no effect for now, because the cursor is always
drawn. This is in preparation of future changes to vd_bitbltchr_t API.
r270278:
vt(4): Mark cursor position as dirty when we enable/disable it
Sponsored by: The FreeBSD Foundation
r269188: [Rework vb_buffer and vb_rows assignment]
r269192: Remove special handling of console window size.
It's done in vt_upgrade() for all windows.
r269193: Update comments.
r269194: Revise font initialization handling.
Sponsored by: The FreeBSD Foundation
Allow efifb to be used with xf86-video-scfb. This is important for EFI
systems without either a CSM or real graphics drivers, such as my
Lenovo Haswell laptop.
This provides working X with the small complication of a console
cursor permanently overlaid on the upper-left corner of the screen
that will be dealt with later.
Also remove some redundant screen clearing.
Sponsored by: The FreeBSD Foundation
r268771:
Allow console drivers active from early boot to be used with
xf86-video-scfb, rather than only drivers attached later on. This
involves a small amount of code duplication with dev/fb/fbd.c, which
will fixed later on.
Also improve performance of vt_blank() by making it not read from the
framebuffer unnecessarily.
r268796:
Fix embarassing typos I made.
Sponsored by: The FreeBSD Foundation
On my Lenovo laptop, the firmware maps the EFI framebuffer with MTRRs
set to uncacheable. This leads to execrable console performance. Once
PMAP is up, remap the framebuffer as write-combining. This reduces
boot time on my laptop by 60% when booting with EFI.
Update hptnr(4) driver to version 1.0.1 supplied by the vendor.
v1.0.1 2014-8-19
* Do not retry the command and reset the disk when failed to enable or
disable spin up feature.
* Fix up a bug that disk failed to probe if driver failed to access the
10th LBA.
* Fix a bug that request timeout but it has been completed in certain
cases.
* Support smartmontool for R750.
Many thanks to HighPoint for continued support of FreeBSD!
Add a tunable "hw.mfi.mrsas_enable" to allow mfi(4) to drop priority and
allow mrsas(4) from LSI to attach to newer LSI cards that are support by
mrsas(4). If mrsas(4) is not loaded into the system at boot then mfi(4)
will always attach. If a modified mrsas(4) is loaded in the system. That
modification is return "-30" in it's probe since that is between
BUS_PROBE_DEFAULT and BUS_PROBE_LOW_PRIORITY.
This option is controller by a new probe flag "MFI_FLAGS_MRSAS" in mfi_ident
that denotes cards that should work with mrsas(4). New entries that should
have this option.
This is the first step to get mrsas(4) checked into FreeBSD and to avoid
collision with people that use mrsas(4) from LSI. Since mfi(4) takes
priority, then mrsas(4) users need to rebuild GENERIC. Using the
.disabled="1" method doesn't work since that blocks attaching and the
probe gave it to mfi(4).
MFC r267451 (by delphij):
Correct variable for loader tunable variable hw.mfi.mrsas_enable.
Use the "bSubslotSize" and "bSubFrameSize" fields to obtain the actual
sample size. According to the USB audio frame format specification
from USB.org, the value in the "bBitResolution" field can be less than
the actual sample size, depending on the actual hardware, and should
not be used for this computation.
PR: 192755
- It was decided to change the driver name to if_ixl for FreeBSD
- This release adds the VF Driver to the tree, it can be built into
the kernel or as the if_ixlv module
- The VF driver is independent for the first time, this will be
desireable when full SRIOV capability is added to the OS.
Submitted by: jack.vogel@intel.com and eric.joyner@intel.com
If eapol packets are sent at the lowest rate, key negotiation will
become more reliable.
Submitted by: Akinori Furukoshi <moonlightakkiy at yahoo dot ca>
Rework when the Tx queue completion interrupt is enabled
The Tx interrupt is now kept disabled in the common case, only
enabled when the number of free descriptors in the queue falls
below a threshold. Transmitted frames are cleared from the VQ
before subsequent transmit, or in the watchdog timer.
This was a very big performance improvement for an experimental
Netmap bhyve backend.
r269413, r269428, r269440, r269537, r269644, r269731, and the cxgbe
portion of r270063.
r266571:
cxgbe(4): Remove stray if_up from the code that creates the tracing ifnet.
r266757:
cxgbe(4): netmap support for Terminator 5 (T5) based 10G/40G cards.
Netmap gets its own hardware-assisted virtual interface and won't take
over or disrupt the "normal" interface in any way. You can use both
simultaneously.
For kernels with DEV_NETMAP, cxgbe(4) carves out an ncxl<N> interface
(note the 'n' prefix) in the hardware to accompany each cxl<N>
interface. These two ifnet's per port share the same wire but really
are separate interfaces in the hardware and software. Each gets its own
L2 MAC addresses (unicast and multicast), MTU, checksum caps, etc. You
should run netmap on the 'n' interfaces only, that's what they are for.
With this, pkt-gen is able to transmit > 45Mpps out of a single 40G port
of a T580 card. 2 port tx is at ~56Mpps total (28M + 28M) as of now.
Single port receive is at 33Mpps but this is very much a work in
progress. I expect it to be closer to 40Mpps once done. In any case
the current effort can already saturate multiple 10G ports of a T5 card
at the smallest legal packet size. T4 gear is totally untested.
trantor:~# ./pkt-gen -i ncxl0 -f tx -D 00:07:43🆎cd:ef
881.952141 main [1621] interface is ncxl0
881.952250 extract_ip_range [275] range is 10.0.0.1:0 to 10.0.0.1:0
881.952253 extract_ip_range [275] range is 10.1.0.1:0 to 10.1.0.1:0
881.962540 main [1804] mapped 334980KB at 0x801dff000
Sending on netmap:ncxl0: 4 queues, 1 threads and 1 cpus.
10.0.0.1 -> 10.1.0.1 (00:00:00:00:00:00 -> 00:07:43🆎cd:ef)
881.962562 main [1882] Sending 512 packets every 0.000000000 s
881.962563 main [1884] Wait 2 secs for phy reset
884.088516 main [1886] Ready...
884.088535 nm_open [457] overriding ifname ncxl0 ringid 0x0 flags 0x1
884.088607 sender_body [996] start
884.093246 sender_body [1064] drop copy
885.090435 main_thread [1418] 45206353 pps (45289533 pkts in 1001840 usec)
886.091600 main_thread [1418] 45322792 pps (45375593 pkts in 1001165 usec)
887.092435 main_thread [1418] 45313992 pps (45351784 pkts in 1000834 usec)
888.094434 main_thread [1418] 45315765 pps (45406397 pkts in 1002000 usec)
889.095434 main_thread [1418] 45333218 pps (45378551 pkts in 1001000 usec)
890.097434 main_thread [1418] 45315247 pps (45405877 pkts in 1002000 usec)
891.099434 main_thread [1418] 45326515 pps (45417168 pkts in 1002000 usec)
892.101434 main_thread [1418] 45333039 pps (45423705 pkts in 1002000 usec)
893.103434 main_thread [1418] 45324105 pps (45414708 pkts in 1001999 usec)
894.105434 main_thread [1418] 45318042 pps (45408723 pkts in 1002001 usec)
895.106434 main_thread [1418] 45332430 pps (45377762 pkts in 1001000 usec)
896.107434 main_thread [1418] 45338072 pps (45383410 pkts in 1001000 usec)
...
r268536:
cxgbe(4): Add an iSCSI softc to the adapter structure.
r269076:
Some hooks in cxgbe(4) for the offloaded iSCSI driver.
r269364:
Improve compliance with style.Makefile(5).
r269366:
List one file per line in the Makefiles. This makes it easier to read
diffs when a file is added or removed.
r269411:
cxgbe(4): minor optimizations in ingress queue processing.
Reorganize struct sge_iq. Make the iq entry size a compile time
constant. While here, eliminate RX_FL_ESIZE and use EQ_ESIZE directly.
r269413:
cxgbe(4): Fix an off by one error when looking for the BAR2 doorbell
address of an egress queue.
r269428:
cxgbe(4): some optimizations in freelist handling.
r269440:
cxgbe(4): Remove an unused version of t4_enable_vi.
r269537:
cxgbe(4): Do not run any sleepable code in the SIOCSIFFLAGS handler when
IFF_PROMISC or IFF_ALLMULTI is being flipped. bpf(4) holds its global
mutex around ifpromisc in at least the bpf_dtor path.
r269644:
cxgbe(4): Let caller specify whether it's ok to sleep in
t4_sched_config and t4_sched_params.
r269731:
cxgbe(4): Do not poke T4-only registers on a T5 (and vice versa).
Relnotes: Yes (native netmap support for Chelsio T4/T5 cards)
Remove aicasm as a build dependency. It made sense when the ahc and ahd
drivers and their firmware were under active development, but those days
have passed. The firmware now exists in pre-compiled form, no longer
dependent on it's sources or on aicasm. If you wish to rebuild the
firmware from source, the glue still exists under the 'make firmware'
target in sys/modules/aic7xxx.
This also fixes the problem introduced with r257777 et al with building
kernels the old fashioned way in sys/$arch/compile/$CONFIG when the
ahc/ahd drivers were included.
Changes to how the aicasm tool is built. This series of changes results
in the aicasm tool being built as part of the tools stages of world and
kernel builds.
Most of these changes will ultimately be undone when r260401 is MFC'd,
but it will leave in place the new kernel-build-tool machinery (KTMAKE
stuff) in case a new special kernel tool ever comes along.
Rename vt_generate_vga_palette() to vt_generate_cons_palette() and
change it to build a palette where the color index is the same than in
terminal escape codes, not the VGA index. That's what TCHAR_CREATE()
uses and passes to vt(4).
The main differences between both orders are:
o Blue and red are swapped (1 <-> 4)
o Yellow and cyan are swapped (3 <-> 6)
The problem remained unnoticed, because the RGB bit indexes passed to
vt_generate_vga_palette() were reversed. This inversion was cancelled
by the colors inversions in the generated palette. For instance, red
(0xff0000) and blue (0x0000ff) have bytes in opposite order, but were
swapped in the palette. But after changing the value of blue (see last
paragraph), the modified color was in fact the red one.
While here, tune the palette to better match console colors and improve
the readability (especially the dark blue).
This is an MFC of r269783 and r269791.
r269314:
Bring in LSI's phase16 - phase18 changes
* Implements Start Stop Unit for SATA direct-attach devices in IR mode to avoid
data corruption.
* Use CAM_DEV_NOT_THERE instead of CAM_SEL_TIMEOUT and CAM_TID_INVALID
r269316:
Bring in LSI's phase19 changes
* Removed unused mpssas_discovery_timeout function.
* Don't alter mapping boundaries if not raid firmware.
* Check free_busaddr instead of post_busaddr (diff minimisation really)
Approved by: ken (co-mentor) and smh
Ignore IIC_ENOADDR from iicbus_reset() as it only means we have a
master-only controller.
This fixes the iic bus scan with i2c(8) (on supported controllers).
Tested with gpioiic(4).
MFC r267009:
Remove the unnecessary i2c slave address assignment.
The ti_i2c controller only works in the master mode and the i2c address
passed on iicbus_reset() is used to set the controller slave address when
operating as an i2c slave (which isn't currently supported).
When talking to a slave, the slave address is correctly provided to
ti_i2c_tranfer().
Add a bounds verification to the SCL and SDA pin values.
At attach, print the SCL and SDA pin numbers.
Remove a stray blank line.
Remove the GPIOBUS locking from gpioiic_reset(), it is already called with
this lock held. This fixes a crash when you try to scan the iicbus with
i2c(8).
use the correct netmap <-> nic slot mapping on the transmit ring for 'lem'.
This bug would manifest only in netmap mode and on packets transmitted after
a NIC reset while netmap mode is active.
In several functions, vtbuf_putchar() in particular, the lock on vtbuf
is acquired twice:
1. once by the said functions;
2. once in vtbuf_dirty().
Now, vtbuf_dirty_locked() and vtbuf_dirty_cell_locked() allow to
acquire that lock only once.
This improves the input speed of vt(4). To measure the gain, a
50,000-lines file was displayed on the console using cat(1). The time
taken by cat(1) is reported below:
o On amd64, with vt_vga:
- before: 1.0"
- after: 0.5"
o On sparc64, with creator_vt:
- before: 13.6"
- after: 10.5"
This is an MFC of r269780.
Use a separate variable for resource id, because 'i' may increment at a
rate greater than 1 on each iteration.
Handle various ways that interrupt config data can be malformed by
warning and assuming more or less reasonable values.
Set ofwbus and simplebus to attach during BUS_PASS_BUS.
Define names that drivers can use to adjust their position relative to
other drivers within a BUS_PASS
Adjust ofwbus and simplebus to attach at BUS_PASS_ORDER_MIDDLE, so that
a platform can attach some other bus first if necessary.
Set the pl310 L2 cache driver to attach during the middle of BUS_PASS_CPU.
Attach arm generic interrupt and timer drivers in the middle of
BUS_PASS_INTERRUPT and BUS_PASS_TIMER, respectively.
Add an arm option, ARM_DEVICE_MULTIPASS, used to opt-in to multi-pass
device attachment on arm platforms. If this is defined, nexus attaches
early in BUS_PASS_BUS, and other busses and devices attach later, in the
pass number they are set up for. Without it defined, nexus attaches in
BUS_PASS_DEFAULT and thus so does everything else, which is status quo.
Merge if_nf10bmac(4), a driver to support an NetFPGA-10G Embedded
CPU Ethernet Core.
The current version operates on a simple PIO based interface connected
to a NetFPGA-10G port.
To avoid confusion: this driver operates on a CPU running on the FPGA,
e.g. BERI/mips, and is not suited for the PCI host interface.
Adjust the register layout to allow for 64bit registers in the
future for nf10bmac(4). Also, add support for and enable RX interrupts.
Allow switching between 32bit and 64bit bus width data access at compile
time by setting NF10BMAC_64BIT and using a REGWTYPE #define to set correct
variable and return value widths.
Adjust comments to indicate the 32 or 64bit register widths.
Relnotes: yes
Sponsored by: DARPA/AFRL
Use ETHER_ALIGN as argument to m_adj() to offset the beginning of packet
rather than the magic number 2.
While here fix a typo in a comment.
No functional changes.
Sponsored by: DARPA/AFRL
Move the tcp_fields_to_host() and tcp_fields_to_net() (inline)
functions to the tcp_var.h header file in order to avoid further
duplication with upcoming commits.
Reviewed by: np
Bite the bullet and start removing the first compile time warnings
by removing unsued file local functions and then unused callees.
A lot more warnings to resolve but someone had to break the ice.
X-Comment: I am not the new maintainer; chime in, it's ours.
Previously the tunables and sysctls had different names for example:
hw.ixgbe.enable_aim => hw.ix.enable_aim
Anyone using ixgbe tunables should ensure they update /boot/loader.conf.
This is a direct commit to stable as the changes to sysctls in head
already fix this issue in a different way.
Sponsored by: Multiplay
