Update some comments on code, specifying the correct vlans used on switch
setup.
Advertise the proper switch operation mode (the rtl8366rb only support
dot1q vlans).
This fixes the breakage that i introduced on r249752 and make the rtl8366rb
switch works again with etherswitchcfg(8).
Tested on TP-Link 1043ND.
Tested by: me, Harm Weites (harm at weites.com)
(pvid=1) and we already configure them to send to other ports.
Setting pvid=portnum would mean that there were separate vlangroups
for each ports, but 'leaking' into other ports. The result? All port
traffic flooded to all other port traffic.
Tested:
* DB120, AR9344 + AR8327 switch
The OpenWRT AR8xxx switch support flushes the ATU (address translation
unit) after each port link 'up' status change. I've modified this to
just flush on any port transition.
Whilst here, bump the number of ports on the AR8327 to 6, rather than
the default of 5. It's DB120 specific; I'll go and make this configurable
later.
There's some debugging code in here still; I am still debugging whether
this is or isn't working fully.
Tested:
* DB120, AR9344 + AR8327 switch
Obtained from: OpenWRT
This patch does four things:
* it globally disables mirroring;
* it globally sets the mirroring on each port to be disabled;
* the initial port setup now programs a portmask for the port to allow
transmission (forwarding) to all other ports bar itself;
* the vlan setup path now programs the portmask for the port to
allow transmission (forwarding) to all other ports bar itself.
Before this, I hard-coded the portmask to 0x3f which would mean all
ports (bar port 6, which currently isn't hooked up to anything.)
This means that traffic would be duplicated back out the port it
received it. I bet this wasn't .. optimal.
In any case, this _seems_ to make DHCP from my macosx laptop
work through this access point. I'll do some further testing
to ensure it's actually working correctly on all my devices.
Tested:
* DB120, AR8327 switch
It's still hardcoded (for db120) but it is now hardcoded in all the
same place (ie, the pdata path.) The port config/status code now checks
port0/port6 as appropriate to configure things.
Tested:
* Qualcomm Atheros DB120, AR8327 switch.
This is (almost!) enough to actually probe, attach, configure a default
port group and do some basic work. It's also totally hard-coded for
the Qualcomm Atheros DB120 board - it doesn't yet have any of the code
from OpenWRT which parses extra configuration data to know how to program
the switch. The LED stuff is also missing.
But, it's enough to facilitate board, PHY, switch and VLAN bringup,
so I am committing it now.
Tested:
* Qualcomm Atheros DB120
Obtained from: OpenWRT
switches.
* Add some new VLAN HAL methods that will be used by the VLAN configuration
code. The AR933x and later switches use slightly different register
layouts (even though the driver currently doesn't support it.)
HAL methods.
This allows the AR8327 code to override it as appropriate.
Tested:
* DB120 - AR8327 and AR9340 on-board switch; only running 'etherswitchcfg'
to check configs. The actual VLAN programming wasn't tested.
The registers (and perhaps the flags) are different for the AR8327, so
I'll stub those out until they're written.
Tested:
* DB120 - both on-chip AR9340 and AR8327 switches.
a single port to setup.
This may end up later being used as part of some logic to program
the PHY for a single port, rather than having to reinitialise them
all at once.
Tested:
* DB120
shifts into the sign bit. Instead use (1U << 31) which gets the
expected result.
This fix is not ideal as it assumes a 32 bit int, but does fix the issue
for most cases.
A similar change was made in OpenBSD.
Discussed with: -arch, rdivacky
Reviewed by: cperciva
* Do the hardware setup in the right order!
* Modify/improve the chip probe check so it can actually
probe the 7240/9340 directly (although it's not yet used..)
* Initialise and fetch the is_mii option
* Fix some debugging whilst I'm here.
This is enough to get things off the ground.
Tested:
* AR9344 SoC
* Add an AR9340 switch version entry;
* Support the switch being connected via MII;
* Add a flag to note that a switch is actually an internal
switch rather than an external switch.
Now:
* The ar9340 switch can interconnect via MII;
* Since some slightly different phy/switch register access methods
and quirks appear for the internal versus external switch,
we will need a flag to mark it as an "internal" switch.
Tested:
* AR9344 (internal switch)
* AR9331 (internal switch)
TODO:
* Test the AR8316 switch!
This is just the chip initialisation code (for now.)
It's not linked into the main build as it requires a bunch of other code
to be tidied up and committed. But it indeed does function as advertised.
Tested:
* AR9344 SoC
arswitch_writereg() routine was writing the registers in the wrong order.
Revert -r241918 as the root problem is now fixed. Remove another workaround
from arswitch_ar7240.c.
Simplify and fix the code on arswitch_writephy() by using
arswitch_writereg().
While here remove a redundant declaration from arswitchvar.h.
Approved by: adrian (mentor)
This fix the case when etherswitch is printing the information of port 0
vlan group (in port based vlan mode) with no member ports.
Add the ETHERSWITCH_VID_VALID support to ip17x driver.
Add the ETHERSWITCH_VID_VALID support to rt8366 driver.
arswitch doesn't need to be updated as it doesn't support vlans management
yet.
Approved by: adrian (mentor)
