e.g. boot_mute, boot_single, boot_verbose, and friends; we checked for these
in multiple places, consolidate into common/ and allow a setting of "NO" for
any of these to turn them off. This allows systems with multiple
loader.conf(5) or loader.conf(5) overlay systems to easily turn off
variables in later processed files by setting it to NO.
Reported by: Nick Wolff @ iXsystems
Reviewed by: imp
If the check for a UFS partition at offset 0 on the disk fails, check
to see if there's a BSD disklabel at block 1 (standard) or at offset
512 (install images assume 512 sector size). If found, probe for UFS
on the 'a' partition.
This fixes UEFI booting images from a BSD labeled MBR slice when the
'a' partiton isn't at offset 0. This is a stop-gap fix since we plan
on removing boot1.efi in FreeBSD 12. We can't easily do that for 11.2,
however, hence the short MFC window.
Tested by: emaste@
MFC After: 3 days
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D15598
- We should be setting a known graphics mode on conout, but we aren't.
- We shouldn't be setting gop mode if we didn't find a good resolution to
set, but we were. This made efi_max_resolution=1x1 effectively worthless,
since it would always set gop mode 0 if nothing else.
Harry Schmalzbauer reports that some firmware, in his experience, trips
over the ESP we install due to the volume label. It has been theorized that
this is due to some confusion with the label and the path on the ESP to
boot1.efi.
Regardless, Harry found that renaming the label seems to fix it.
PR: 214282
MFC after: 3 days
Refactor the currdev setting to find the device we booted from. Limit
searching when we don't already have a reasonable currdev from that to
the same device only. Search a little harder for ZFS volumes as that's
needed for loader.efi to live on an ESP.
Sponsored by: Netflix
Differential Review: https://reviews.freebsd.org/D13784
If the network interface or the uefi implementation do not support the
ReceiveFilter interface do not return only and just print a message.
U-Boot doesn't support is and likely never will. Also even if this fails
it doesn't mean that network in EFI isn't supported.
UGA does not have the same kind of mode enumeration that GOP does. Implement
it instead as a call to text_autoresize so that firmwares with only UGA
present still get some kind of autoresizing behavior.
While here, rename a typo'd "gop" to "uga", although it will remain unused
for the time being.
Not all systems use efifb; pull hw.vga.textmode and choose a good console
mode instead if it's set to something non-zero. This is basically a revival
of the code that used to live in boot1, but instead rebased onto this
different way of doing mode selection in loader.efi.
Interestingly enough, the regression that was previously introduced where
GOP would not reflect the console setting does not seem to exist when
console mode selection is done here. I've not done any investigation as to
why this is the case. Nevertheless, boot1.efi is still not the best place to
do mode selection.
Default the max resolution to 1080p, we'll accept Width x Height
specifications along with the following presets:
- 480p
- 720p
- 1080p
- 2160p or 4k
- 5k
PR: 224825
Differential Revision: https://reviews.freebsd.org/D14801
boot1 is too early to be deciding a good resolution. Console modes don't map
cleanly/predictably to actual screen resolutions, and GOP does not reflect
the actual screen resolution after a console mode change. Rip it out.
Add an efi-autoresizecons command to loader to choose an optimal screen
resolution based on the current environment. We'll explicitly execute this
later, preferably before we draw anything of value but after we load config
and pick up any tunables we may need to decide where we're going.
This method also allows us to actually pass the correct framebuffer
information on to the kernel.
UGA autoresizing is not implemented because it doesn't have the kind of mode
enumeration that GOP does. If an interested person with relevant hardware
could get in contact, we can take a look at implementing UGA autoresize.
This effectively "fixes" the breakage caused by r327058, but doesn't
actually set the resolution correctly until the interpreter calls
efi-autoresizcons. The lualoader version of this has been included for
reference; the forth equivalent will follow.
Reviewed by: imp (with some hestitation), manu
Differential Revision: https://reviews.freebsd.org/D14788
This fixes a problem encountered on the Lenovo Thinkpad X220/Yoga 11e where
runtime services would try to inexplicably jump to other parts of memory
where it shouldn't be when attempting to enumerate EFI vars, causing a
panic.
The virtual mapping is enabled by default and can be disabled by setting
efi_disable_vmap in loader.conf(5).
Reviewed by: kib (earlier version)
MFC after: 3 weeks
Differential Revision: https://reviews.freebsd.org/D14677
A foolish consistency is the hobgoblin of little minds, adored by
little statesmen and philosophers and divines. With consistency a
great soul has simply nothing to do. -- Ralph Waldo Emerson
The current system is fragile and requires very careful layout of all
*_devdesc structures. It also makes it hard to change the base
devdesc. Take a page from CAM and put the 'header' in all the derived
classes and adjust the code to match.
For OFW, move the iHandle h_handle out of a slot conflicting with
d_opendata. Due to quirks in the alignment rules, this worked.
However changing the code to use d_opendata storage now that it's a
pointer is hard, so just have a separate field for it.
All other cleanups were to make the *_devdesc structures match where
they'd taken some liberties that were none-the-less compatible enough
to work.
open_disk uses d_opendata for it's own purpse. We can't store blkio
there. Fortunately, blkio is stored elsewhere and we never actually
retrieve blkio from d_opendata. Eliminate it as a source of confusion.
Eliminate all stores of d_opendata in efi since this layer doesn't own
that field.
One does not simply convert to SUBDIR.yes in stand without making everything
else in the affected files SUBDIR.yes -- there are better ways to do this.
Use SUBDIR.${MK_*} where appropriate. r330248 eliminated most of the
offenders, sweep the rest under the rug.
Differential Revision: https://reviews.freebsd.org/D14545
For directories that don't many anything, add NO_OBJ=t just before we
include bsd.init.mk. This prevents them from creating an OBJ
directory. In addition, prevent defs.mk from creating the machine
related links in these cases. They aren't needed and break, at least
on stable, the read-only src tree build.
There's no reason to have multiple copies of lszfs and
reloadbe. Consolidate them into one location. Also ldi_get_size is the
same everywhere (except sparc64). Make it the same everywhere as the
common definition is more general and will work on spar64.
This solve problem when booting with efi on armv7
Reviewed by: imp, tsoome
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14415
Scan only the BLOCK IO MEDIA once instead of each time for each type of
device (fd, cd and hdd).
Leave the mechanism to free and reprobe all devices if one day we want
to implement a "dev rescan" thing.
Reviewed by: imp, tsoome
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14334
preference to LIBFICL{,32}. LIBFICL{,32} are now always defined, but
LDR_INTERP{,32} is defined empty when building w/o forth (aka the
simple interpreter) and defined to LIBFICL{,32} when we are building
forth.
loader scripts. However, that path won't be taken after all it
seems. Remove this code before it decays into uselessness. Also remove
build dependencies on forth no longer needed.
MK_CTF, MK_SSP, MK_PROFILE, NO_PIC, and INTERNALLIB are always the
same, so set them in defs.mk. MAN= is common, so set it here too.
This removes a lot of boring repetition from the Makefiles that added
almost no value.
This should have been done as part of r327350, but due to lack of foresight
it came later. In the different places we apply overlays, we duplicate the
bits that check for fdt_overlays in the environment and supplement that with
any other places we need to check for overlays to load. These "other places"
will be loader specific and are not candidates for consolidation.
Provide an fdt_load_dtb_overlays to capture the common logic, allow passing
in an additional list of overlays to be loaded. This additional list of
overlays is used in practice for ubldr to pull in any fdt_overlays passed to
it from U-Boot environment, but it can be used for any other source of
overlays.
These additional overlays supplement loader.conf(5) fdt_overlays, rather
than replace, so that we're not restricted to specifying overlays in only
one place. This is a change from previous behavior where loader.conf(5)
supplied fdt_overlays would cause us to ignore U-Boot environment, and this
seems nonsensical- user should have sufficient control over both of these
aspects, or lack of control for good reasons.
A knob could be considered in the future to ignore U-Boot supplied overlays,
but the supplemental treatment seems like a good start.
Reviewed by: imp (earlier version), gonzo (earlier version)
Differential Revision: https://reviews.freebsd.org/D13993
These were found during bring-up on a new arm64 platform and in an
amd64 VM.
Submitted by: Arshan Khanifar <arshankhanifar_gmail.com>
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D14036
When building loader bits, lld fails with the following error:
"ld: error: section: .dynamic is not contiguous with other relro sections"
on both ubldr and EFI loader.
Move .dynamic up to make ld.lld happy, adjust .got as necessary for ubldr.
Tested on: OrangePi One (ld.lld, ubldr)
Tested on: Banana Pi-M3 (ld.lld, ubldr)
Tested on: qemu-armv7 (ld.lld, EFI)
Tested on: qemu-armv7 (ld.bfd, EFI)
Tested on: Raspberry Pi 2 (ld.bfd, ubldr) [manu]
Tested on: Banana Pi-M2 (ld.bfd, ubldr) [manu]
Reviewed by: andrew, emaste, imp
Differential Revision: https://reviews.freebsd.org/D13942
is NULL. That's more correct and doesn't depend on the error behavior
of utf8_to_ucs2. In practice, we'll never see this though since we
pass utf8_to_ucs2 a well formed string.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D13918
and utf8_to_ucs2, be sure to NULL out the return pointer too, rather
than return a pointer to free memory.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D13917
utf8_to_ucs2 in boot1.efi. We need to initialise the ucs2 output string
so it will allocate space, and use the return value to determine if the
call was successful.
Reviewed by: imp
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D13915
Use simple "foo" rather than "${.CURDIR}/foo" to include Makefile.fat
since the former works when including this Makefile from else
where. Also, use full path from ${BOOTSRC} to the FAT templates for
similar reasons. It doesn't change anything in base FreeBSD, but
allows us to have a custom boot1.efi more easily (though that will be
short-lived for us, it may also be helpful for others).
Sponsored by: Netflix
Overlays were previously not applied when U-Boot provides FDT or EFI
provides FDT, only when we load FDT from /boot/dtb given name from U-Boot.
Make all three paths lead to loading fdt_overlays and applying them, so that
fdt_overlays can be expected to Just Work.
Reviewed by: gonzo, imp, manu
Differential Revision: https://reviews.freebsd.org/D13664
This patch allows to scan all display modes in boot1 as loader does.
Before system tried to select optimal display mode by sequential scan of
modes and if error then stop scanning. This way is not good, because
if mode N is not present, mode N+1 may exist.
In loader we use conout->Mode->MaxMode to identify maximum number of modes.
This commit is to use same way in boot1 as in loader.
Reported by: Andrey Pustovetov <andrey.pustovetov@gmail.com>
Reviewed by: tsoome
Differential Revision: https://reviews.freebsd.org/D13541
removing this argument, and expanding when rc is NULL. This
effectively completes the back out of custom scripts for tftp booted
loaders from r269153 that was started in r292344 with the new path
tricks that obsoleted it.
Submitted by: Netflix
HELP_FILES is a loader only thing, so move it to loader.mk. Only
generate the help file if HELP_FILES is defined. Adjust Makefiles to
new convention. Fix a few cases where ${.CURDIR}/ was missing
resulting in missing bits from the help files.
Sponsored by: Netflix
Use _STANDALONE for guard expression in efichar.[ch] and add efi_char typedef.
clean up boot1.c, and replace for loop in efipart.c with ucs2len().
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D13488
Don't print when we can't find a file. Copy it instead to the error
buffer. Higher level routines determine if it's appropriate to print
the error message.
Also, remove dead code (labeled bogusly lost functionality) since we
never used that functionality. Remove unused arg from interact() too.
Sponsored by: Netflix
latter aren't used. Prefer sys/link_elf.h to link.h so we're only
dependent on the kernel tree. The default installation of link.h just
includes this file, and any benefit from that is outweighed by the
hassle it causes. This reduces the footprint of files needed from the
system includes (or sysroot in buildworld).
Sponsored by: Netflix
Remove the now-useless dependency on ufsread.c. In some cases, it was
on the wrong file. But in all cases, we now automatically generate
.depend files, so we don't need it explicitly.
Sponsored by: Netflix
iPXE does insert stub BLOCK IO protocol handle to rework other issues,
this handle is not usable as it does not provide actual implementation.
We can detect this situation by checking and validating the BlockSize
property, so this update does make sure we have BlockSize at least 512B
and its value is power of 2.
PR: 223969
Reported by: Jeff Pieper
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D13297
Rework the block device handle check to allow more robust device
classification. This is mostly usability issue - it can be quite confusing
for user when no disks are listed with lsdev.
Add more comments about what and why is done.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D13026
simd / no float stuff is centeralized here. Also centralise
-ffreestanding since it is specified everywhere.
This, along with a change to share/mk/bsd.cpu.mk to include -mno-avx2
in CFLAGS_NO_SIMD should fix building for newer machines (eg with
CPUTYPE=haswell) where clang was generating avx2 instructions.
Sponsored by: Netflix
