I/O clock. Thankfully, the simple executive provies a way to querry
the proper clock that works on all models. Move to asking for the SCLK
via this interface.
This gets the serial console working after we start init and open the
console and set the divisor (which turned the output from good to
bad). I can login on the console now.
than blocking the vCPU thread. This improves bulk data performance
by ~30-40% and doesn't harm req/resp time for stock netperf runs.
Future work will use a thread pool rather than a thread per tx queue.
Submitted by: Dinakar Medavaram
Reviewed by: neel, grehan
Obtained from: NetApp
silently overwriting the previous assignment.
Gripe if the emulation is not recognized instead of silently ignoring the
emulated device.
If an error is detected by pci_parse_slot() then exit from the command line
parsing loop in main().
Submitted by (initial version): Chris Torek (chris.torek@gmail.com)
and tuned value, we would advertise the unsupported value to CAM and it would
merrily destroy the controller with way too many IO operations.
This manifests itself in a Zero Memory RAID configuration for a P410 and
possibly other controllers.
Obtained from: Yahoo! Inc.
MFC after: 2 weeks
mergemaster. This allows bootstrap verions of tools to be used.
Add a note to UPDATING about this change.
Discussed with: jhb
Sponsored by: DARPA, AFRL
MFC after: 5 days
These APIs were relevant when memory for virtual machine allocation was
hard partitioned away from the rest of the system but that is no longer
the case. The sysctls that provided this information were garbage collected
a while back.
Obtained from: NetApp
in the pcb. setjmp/longjmp in the kernel also used these values, so
continue to use them although their use isn't technically the pcb
register array (matching is all that's important for setjmp/longjmp in
the kernel). Finally, eliminate the old register names from regnum.h.
This is a lexical change only. The non-debug .o files have the same md5.
same place as dst, or to the sockaddr in the routing table.
The const constraint of gw makes us safe from modifing routing table
accidentially. And "onstantness" of dst allows us to remove several
bandaids, when we switched it back at &ro->ro_dst, now it always
points there.
Reviewed by: rrs
USDT probes are advertised to kernel by initialization code with
atrribute((constructor))). It seems that on Solaris the .init-ish code
of the main object is executed before RD_PREINIT point is hit. On
FreeBSD that is not the case. And because on FreeBSD there is no other
well-defined point between RD_PREINIT and main() we have to parse a
DTrace script when main is hit, for time being.
A footnote: currently we actually post RD_POSTINIT event, but that's a
bug because the event is triggered by hitting r_debug_state which
happens before any init code is executed.
Reported by: markj
snapshot.
Related illumos ZFS issue:
3699 zfs hold or release of a non-existent snapshot does not output error
Reported by: Steven Hartland <smh@FreeBSD.org>
MFC after: 3 days
Rework the guest register fetch code to allow the RIP to
be extracted from the VMCS while the kernel decoder is
functioning.
Hit by the OpenBSD local-apic code.
Submitted by: neel
Reviewed by: grehan
Obtained from: NetApp
Merge vendor bugfix for a possible deadlock related to async destroy
and improve write performance by introducing a new lock protecting
tx_open_txg.
Illumos ZFS issues:
3642 dsl_scan_active() should not issue I/O to determine if async
destroying is active
3643 txg_delay should not hold the tc_lock
MFC after: 1 week
route. What it was is there are two places in ip_output.c
where we do a goto again. One place was fine, it
copies out the new address and then resets dst = ro->rt_dst;
But the other place does *not* do that, which means earlier
when we found the gateway, we have dst pointing there
aka dst = ro->rt_gateway is done.. then we do a
goto again.. bam now we clobber the default route.
The fix is just to move the again so we are always
doing dst = &ro->rt_dst; in the again loop.
PR: 174749,157796
MFC after: 1 week
GDT from the correct segment, otherwise a triple fault would be caused.
In some virtual environments (VMware, VirtualBox, etc) this could lead
to a unhandled error or hang in the guest emulation software.
Thanks to avg and jhb for a few hints in the right direction.
Noticed by: Jeremy Chadwick <jdc@koitsu.org> (and many others)
MFC after: 1 week
instead of kernel_map size to prevent kernel memory exhaustion
by mbufs and a subsequent panic on physical page allocation
failure.
On architectures without a direct map all mbuf memory (except
for jumbo mbufs larger than PAGE_SIZE) comes from kmem_map.
It is the limiting factor hence.
For architectures with a direct map using the size of kmem_map
is a good proxy of available kernel memory as well. If it is
much smaller the mbuf limit may be sub-optimal but remains
reasonable, while avoiding panics under exhaustion.
The overall mbuf memory limit calculation may be reconsidered
again later, however due to the many different mbuf sizes and
different backing KVM maps it is a tricky subject.
Found by: pho's new network stress test
Pointed out by: alc (kmem_map instead of kernel_map)
Tested by: pho
LoopVectorizer: Fix 15830. When scalarizing and unrolling stores make
sure that the order in which the elements are scalarized is the same
as the original order.
This fixes a miscompilation in FreeBSD's regex library.
This should fix lib/libc/regex/regcomp.c at -O3 with clang 3.3 r178860
on CPUs with SSE. Before this change, the vectorizer could incorrectly
rearrange the second loop in computejumps(), leading to possibly invalid
entries in the re_gets::charjump table.
The net result was that for example "sed s/@CC@/foo/" failed to work
correctly, leading to trouble with many configure scripts.
descriptors. Prior to this change the device would only work with guests
that chose to use indirect descriptors.
Modify the device reset callback to actually reset the device state.
Submitted by: Tycho Nightingale (tycho.nightingale@pluribusnetworks.com)
