- If the path cost is calculated when the link is down, set a pending flag so
it is calculated again when it comes back up.
- To not use 00:00:00:00:00:00 as the bridge id, all interfaces are scanned and
the lowest number wins. All zeros is too low.
Approved by: re (rwatson)
of the bridge port and path cost have been administratively set or
calculated automatically by RSTP.
Make sure to transition from non-edge to edge when the port goes down
and the edge flag was manually set before.
This is needed to comply with the condition
((!portEnabled && AdminEdge) || ....)
in the Bridge Detection State Machine (IEE802.1D-2004, p. 171).
Reviewed by: thompsa
Approved by: bz (mentor)
- use flags rather than sperate ioctls for edge, p2p
- implement p2p and autop2p flags
- define large pathcost constant as ULL
- show bridgeid and rootid in ifconfig
Obtained from: Reyk Floeter <reyk@openbsd.org>
- Each stp port is added sequentially so it was possible for our bridgeid to
change every time because the new port has a lower MAC address. Instead
just find the lowest MAC address from all Ethernet adapters in the machine
as the value only needs to be unique, this stops a lot of churn on the
protocol.
- Update the states after enabling or disabling a port.
- Keep tabs if we have been stopped or started by our parent bridge.
- The callout only needs to be drained before destroying the mutex, move it to
bstp_detach.
RSTP provides faster spanning tree convergence, the protocol will exchange
information with neighboring switches to quickly transition to forwarding
without creating loops. The code will default to RSTP mode but will downgrade
any port connected to a legacy STP network so is fully backward compatible.
Reviewed by: syrinx
Tested by: syrinx
will remain in the disabled state until another link event happens in the
future (if at all). Add a timer to periodically check the interface state and
recover.
Reported by: Nik Lam <freebsdnik j2d.lam.net.au>
MFC after: 3 days
- use the cu_bridge_id rather than the cu_rootid for the bridge address [1]
- the memcmp return value is not signed so the wrong interface may have been
selected
- fix up the calculation of sc_bridge_id
PR: kern/93909 [1]
MFC after: 3 days
that the following funtions are not used, wrap in '#ifdef noused' for the
moment.
bstp_enable_change_detection
bstp_disable_change_detection
bstp_set_bridge_priority
bstp_set_port_priority
bstp_set_path_cost
- move the function pointer definitions to if_bridgevar.h
- move most of the logic to the new BRIDGE_INPUT and BRIDGE_OUTPUT macros
- remove unneeded functions from if_bridgevar.h and sort a little.
could initialise while unlocked if the bridge is not up when setting the inet
address, ether_ioctl() would call bridge_init.
Change it so bridge_init is always called unlocked and then locks before
calling bstp_initialization().
Reported by: Michal Mertl
Approved by: mlaier (mentor)
MFC after: 3 days
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
hooks for each outgoing interface but also run pfil hooks _N times_ on the
bridge interface. This is changed so pfil hooks are run once for the bridge
interface (bridge0) and then only on the outgoing interfaces in the broadcast
loop.
- Simplify bridge_enqueue() by moving bridge_pfil() to the callers.
- Check (inet6_pfil_hook.ph_busy_count >= 0), it may be possible to have a
packet filter hooked for only ipv6 but we were only checking if ipv4 hooks
were busy.
- Minor optimisation for null mbuf check after bridge_pfil(), move it into the
if-block as it couldnt possibly be null outside.
Prodded by: mlaier
Approved by: re (scottl), mlaier (mentor)
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
spanning tree support.
Based on Jason Wright's bridge driver from OpenBSD, and modified by Jason R.
Thorpe in NetBSD.
Reviewed by: mlaier, bms, green
Silence from: -net
Approved by: mlaier (mentor)
Obtained from: NetBSD
