old type (stty) ioctls can easily bypass locking bits.
It involves manual conversion from old ioctls to new ones,
large piece of code duplicated from tty_compat.c
after ttioctl too, because it can change t_line.
Remove (TS_CNTTB | TS_LNCH) test, it is always inherits from
old tty mode and can't be reach in currently setted mode.
o the includes are now properly done by <sys/foo.h> instead of "foo.h"
o a bunch of undeclared functions has been resolved
o pcvt finally supports devconfig
* to reduce the number of adapter failures. Transceiver select
* logic changed to use value from EEPROM. Autoconfiguration
* features added.
Submitted by: "Serge A. Babkin" <babkin@hq.icb.chel.su>
Etherlink III 'zp' on 2.0R, but it did not work with the -current.
Noriyuki Takahashi <hor@aecl.ntt.jp> san has fixed this bug.
Our alpha-testers are tested this driver with 3C589B-COMBO and
3C589B-TP. And it works fine.
I also fixed a little about the use of ZP_DEBUG symbol and beautified
the awful Frankenstein-style indent :-) with "indent -c0 -nfc1 -i4".
[Also merge with Bruce's last changes]
Submitted by: "HOSOKAWA Tatsumi" <hosokawa@mt.cs.keio.ac.jp>
update what has actually been touched. This should speed up
screen access on slow hardware.
Introduced setting of "destructive" cursor size, much like
the old hardware cursor.
if (tp->t_line != 0)
test when CS_ODONE, it fails for NTTYDISC, use
if (linesw[tp->t_line].l_start != ttstart)
instead.
Reviewed by:
Submitted by:
Obtained from:
CVS:
BREAK/parity/framing errors.
Term "correctly" assumes POSIX spec. and 4.4 ttyinput() behaviour.
1) Discard BREAK/parity at interrupt level when apropriate IGN*
is set in iflag. It helps "raw" mode works even IGN* is set.
2) Zero parity (if INPCK) and framing directly in buffer
before passing it to b_to_q() in "raw" mode.
Efficency:
interrupt level: if no error occurse, only two "test" commands added
"raw" mode: buf scan incc times for parity/framing added
Reviewed by:
Submitted by:
Obtained from:
CVS:
Report floppy/tape units on seperate lines as fdX:/ftX: to correct lots of
ways the current scheme failed to end the output with \n.
Add controller and/or drive designator to the fron of several messages
that come from this drive. [It's not fun to track down driver messages
using grep over the source tree.]
Reviewed by: joerg
- ignore the partition table if it is identical with the bogus one in
/usr/src/sys/i386/boot/biosboot/start.S. Honoring the bogus size
field was fatal. The error is detected but other compatibilty
cruft weakens the error handling too much for this case.
- weaken the partition entry checking to allow the following treatments
of C/H/S addresses when C should be >= 1024:
(1) allow C = 1023, H = max, S = max.
(2) allow C to be correct modulo 1024.
Other compatibilty cruft weakens the error handling to allow all
C/H/S addresses, but there too many errors were reported.
Improve error messages:
- print C/H/S addresses if relevant.
- distinguish primary partition table from extended partition tables.
- don't use diskerr() except for i/o errors.
NOT derived from the Linux code and is thus not GPL'd. It is the author's
express wish that the GPL copyrighted version be removed and this BSD copyright
version take its place. Considering our own stance on this, I'm certainly
not going to argue! [Note to NetBSD folks: You're free to grab it now :-)]
Submitted by: Mikael Hybsch <micke@dynas.se>
ultra14f.c and eliminate constants.
Correct EISA slot scan loops to look at slots 1 to 15 inclusive (off
by 1 errors all over the place). Other drivers need this, I will get
to it after a little more work.
Correct the ultrastore EISA probe so that it starts after the last
EISA slot probed instead of starting over from slot 0.
We need an eisa.h to move a lot of common constants into. I will
write it if someone tells me where it should go (sys/eisa?).
#include <i386/isa/isa.h>
return IO_EISASIZE instead of hard coded 0x1000.
if_ep.c:
Remove commented out disabling of interrupts that gave a
"comment withing a comment" warning.
