The origin of WEP comes from IEEE Std 802.11-1997 where it defines
whether the frame body of MAC frame has been encrypted using WEP
algorithm or not.
IEEE Std. 802.11-2007 changes WEP to Protected Frame, indicates
whether the frame is protected by a cryptographic encapsulation
algorithm.
Reviewed by: adrian, rpaulo
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
The SYSCTL_NODE macro defines a list that stores all child-elements of
that node. If there's no SYSCTL_DECL macro anywhere else, there's no
reason why it shouldn't be static.
reading. (This was already done for writing to a sysctl). This
requires all SYSCTL setups to specify a type. Most of them are now
checked at compile-time.
Remove SYSCTL_*X* sysctl additions as the print being in hex should be
controlled by the -x flag to sysctl(8).
Succested by: bde
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
sleepable context for net80211 driver callbacks. This removes the need for USB
and firmware based drivers to roll their own code to defer the chip programming
for state changes, scan requests, channel changes and mcast/promisc updates.
When a driver callback completes the hardware state is now guaranteed to have
been updated and is in sync with net80211 layer.
This nukes around 1300 lines of code from the wireless device drivers making
them more readable and less race prone.
The net80211 layer has been updated as follows
- all state/channel changes are serialised on the taskqueue.
- ieee80211_new_state() always queues and can now be called from any context
- scanning runs from a single taskq function and executes to completion. driver
callbacks are synchronous so the channel, phy mode and rx filters are
guaranteed to be set in hardware before probe request frames are
transmitted.
Help and contributions from Sam Leffler.
Reviewed by: sam
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
revision and (on Prism cards) the primary firmware revision via
sysctl. Move the printing of this information under bootverbose,
since it is relatively easy to get to it now.
the beginning. There's a race in the shared interrutp case. If
another interrupt happens after the interrupt is setup, then we'd try
to lock an uninitialized mutex. In addition, if we bailed out due to
a too old version of firmware, we'd leave the interrupt enabled with
all the fun that ensues....
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
- Limit grabbing the lock to SIOCSIFFLAGS.
- Move ieee80211_start_all() to SIOCSIFFLAGS.
- Remove SIOCSIFMEDIA as it is not useful.
- Limit ether_ioctl to only SIOCGIFADDR. SIOCSIFADDR and SIOCSIFMTU have no
affect as there is no input/output path in the vap parent. The vap code
will handle the reinit of the mac address changes.
- Split off ndis_ioctl_80211 as it was getting too different to wired devices.
This fixes a copyout while locked and a lock recursion.
Reviewed by: sam
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
mode works properly, previously the hostap channel could not be changed off #3.
Fix an ifp/sc misuse while I am here.
Reported by: many
Approved by: re (bmah)
ioctls can be removed. These have been #ifdef'd out and left as a reference in
case any of the RIDs need to be turned into sysctls at a later date.
Reviewed by: sam, avatar
Approved by: re (kensmith)
- provide dummy routines for ic_scan_curchan and ic_scan_mindwell, we do not support those operations.
- add ieee80211_scan_done() to tell the scanning module that all channels have been scanned.
- pass IEEE80211_S_SCAN state off to net80211 so it can initiate scanning
- fix overflow in the rates array
- scale the rate value passed back from the firmware scan to the units that net80211 uses.
Submitted by: Token
Reviewed by: sam, avatar
Approved by: re (kensmith)
operating channel and use this in the scan cache rather than directly using
ic_curchan. Some firmware cards can only do a full scan and so ic_curchan does
not have the correct value.
Also add IEEE80211_CHAN2IEEE to directly dereference ic_ieee from the channel
to be used in the fast path.
Reviewed by: sam, sephe
Approved by: re (kensmith)
to be index by IEEE channel number but that is no longer the case and it needs
to be searched for.
Submitted by: avatar
Reviewed by: sam
Approved by: re (kensmith)
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
- For ural(4):
o Fix node leakage in ural_start(), if ural_tx_mgt() fails.
o Fix mbuf leakage in ural_tx_{mgt,data}(), if usbd_transfer() fails.
o In ural_tx_{mgt,data}(), set ural_tx_data.{m,ni} to NULL, if
usbd_transfer() fails, so they will not be freed again in ural_stop().
Approved by: sam (mentor)
specific privilege names to a broad range of privileges. These may
require some future tweaking.
Sponsored by: nCircle Network Security, Inc.
Obtained from: TrustedBSD Project
Discussed on: arch@
Reviewed (at least in part) by: mlaier, jmg, pjd, bde, ceri,
Alex Lyashkov <umka at sevcity dot net>,
Skip Ford <skip dot ford at verizon dot net>,
Antoine Brodin <antoine dot brodin at laposte dot net>
(1) bpf peer attaches to interface netif0
(2) Packet is received by netif0
(3) ifp->if_bpf pointer is checked and handed off to bpf
(4) bpf peer detaches from netif0 resulting in ifp->if_bpf being
initialized to NULL.
(5) ifp->if_bpf is dereferenced by bpf machinery
(6) Kaboom
This race condition likely explains the various different kernel panics
reported around sending SIGINT to tcpdump or dhclient processes. But really
this race can result in kernel panics anywhere you have frequent bpf attach
and detach operations with high packet per second load.
Summary of changes:
- Remove the bpf interface's "driverp" member
- When we attach bpf interfaces, we now set the ifp->if_bpf member to the
bpf interface structure. Once this is done, ifp->if_bpf should never be
NULL. [1]
- Introduce bpf_peers_present function, an inline operation which will do
a lockless read bpf peer list associated with the interface. It should
be noted that the bpf code will pickup the bpf_interface lock before adding
or removing bpf peers. This should serialize the access to the bpf descriptor
list, removing the race.
- Expose the bpf_if structure in bpf.h so that the bpf_peers_present function
can use it. This also removes the struct bpf_if; hack that was there.
- Adjust all consumers of the raw if_bpf structure to use bpf_peers_present
Now what happens is:
(1) Packet is received by netif0
(2) Check to see if bpf descriptor list is empty
(3) Pickup the bpf interface lock
(4) Hand packet off to process
From the attach/detach side:
(1) Pickup the bpf interface lock
(2) Add/remove from bpf descriptor list
Now that we are storing the bpf interface structure with the ifnet, there is
is no need to walk the bpf interface list to locate the correct bpf interface.
We now simply look up the interface, and initialize the pointer. This has a
nice side effect of changing a bpf interface attach operation from O(N) (where
N is the number of bpf interfaces), to O(1).
[1] From now on, we can no longer check ifp->if_bpf to tell us whether or
not we have any bpf peers that might be interested in receiving packets.
In collaboration with: sam@
MFC after: 1 month
rather than in ifindex_table[]; all (except one) accesses are
through ifp anyway. IF_LLADDR() works faster, and all (except
one) ifaddr_byindex() users were converted to use ifp->if_addr.
- Stop storing a (pointer to) Ethernet address in "struct arpcom",
and drop the IFP2ENADDR() macro; all users have been converted
to use IF_LLADDR() instead.
