While updating Tx stats, already freed node could be referred and cause
page fault. To avoid such panic, spool Tx stats in driver's softc. Then,
on every ratectl interval, grab node though ieee80211_iterate_nodes() and
update ratectl stats.
* Simplify some code in run_iter_func().
* Fix typo
* Use memset instead of bzero (hselasky @)
PR: kern/153938
Submitted by: PseudoCylon <moonlightakkiy@yahoo.ca>
Approved by: thompsa (mentor)
Drivers which rely on net80211 to create the beacon need to call
ieee80211_beacon_update() on iv_update_beacon() calls. This is required
that certain bits, e.g. TIM, get updated. A call to ieee80211_beacon_alloc()
is not enough because it does not care about flags which can only change
during runtime. By design a beacon is supposed to be allocated only once
while moving into RUN state.
To handle all possible calls to iv_update_beacon() the run_updateslot()
function has been revived and run_updateprot() has been added.
run_updateslot() handles slot time changes and run_updateprot() changes
to protection, both can change while nodes associate/leave.
Submitted by: Alexander Zagrebin <alex at zagrebin.ru>,
PseudoCylon <moonlightakkiy atyahoo.ca>
MFC after: 3 weeks
This fixes hostap mode for at least ral(4) and run(4), because there is
no sufficient call into drivers which could be used initialize the node
related ratectl variables.
MFC after: 3 days
the IEEE80211_C_RATECTL flag set, default to NONE for all drivers. Only if
a driver calls ieee80211_ratectl_init() check if the NONE algo is still
selected and try to use AMRR in that case. Drivers are still free to use
any other algo by calling ieee80211_ratectl_set() prior to the
ieee80211_ratectl_init() call.
After this change it is now safe to assume that a ratectl algo is always
available and selected, which renders the IEEE80211_C_RATECTL flag pretty
much useless. Therefore revert r211314 and 211546.
Reviewed by: rpaulo
MFC after: 2 weeks
opposition to the change, since really we need to implement missing
functionality in drivers or the 802.3 layer.
For now, restore a reminder message for a missing rum_update_mcast, but
print it only once.
callback function will be executed, and that the key won't be deleted during
the init process.
- txmic and rxmic are written into the chip the same place regardless of
opmode.
- Make the hardware generate 802.11 sequence numbers.
Submitted by: Akinori Furukoshi
Obtained from: git://gitorious.org/run/run.git
queue length. The default value for this parameter is 50, which is
quite low for many of today's uses and the only way to modify this
parameter right now is to edit if_var.h file. Also add read-only
sysctl with the same name, so that it's possible to retrieve the
current value.
MFC after: 1 month
This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
message has been printed is enough to get someones attention. Also remove the
line number for DPRINTF/DPRINTFN, it already prints the funtion name and a
unique message.
was major changes to initialize RF chipset and set H/W registers and
removed a lot of magic numbers on code. Details are as follows:
- uses the endpoint 0x89 to get TX status information which used to
get TX complete or retry numbers or get a beacon interrupt. It's
only valuable for RTL8187B.
- removes urtw_write[8|16|32]_i functions that it's useless now.
- uses ic->ic_updateslot to set SLOT, SIFS, DIES, EIFS, CW_VAL
registers that doesn't set these whenever the channel is changed.
- code for initializing RF chipset for RTL8187B changed a lot that
there was many problems on TX transfers so it doesn't work properly
even if just for a ping/pong. Now it becomes more stable than
before that TX throughputs using netperf(1) were about 15 ~ 17Mbps/s
though sometimes it encounters packet losses.
- removes a lot of magic numbers that in the previous all of
representing RX and TX descriptors were consisted of magic numbers
and structures. It'd be more readable rather than before.
- calculates TX duration more accurately for urtw(4) devices.
- style(9)
The newbus lock is responsible for protecting newbus internIal structures,
device states and devclass flags. It is necessary to hold it when all
such datas are accessed. For the other operations, softc locking should
ensure enough protection to avoid races.
Newbus lock is automatically held when virtual operations on the device
and bus are invoked when loading the driver or when the suspend/resume
take place. For other 'spourious' operations trying to access/modify
the newbus topology, newbus lock needs to be automatically acquired and
dropped.
For the moment Giant is also acquired in some key point (modules subsystem)
in order to avoid problems before the 8.0 release as module handlers could
make assumptions about it. This Giant locking should go just after
the release happens.
Please keep in mind that the public interface can be expanded in order
to provide more support, if there are really necessities at some point
and also some bugs could arise as long as the patch needs a bit of
further testing.
Bump __FreeBSD_version in order to reflect the newbus lock introduction.
Reviewed by: ed, hps, jhb, imp, mav, scottl
No answer by: ariff, thompsa, yongari
Tested by: pho,
G. Trematerra <giovanni dot trematerra at gmail dot com>,
Brandon Gooch <jamesbrandongooch at gmail dot com>
Sponsored by: Yahoo! Incorporated
Approved by: re (ksmith)
