errors that plagued those cards with XFree86 4.0. They have two memory
ranges as well as an IO port range to them. Also cleaned up the three
warning messages that I got, from inb(), outb() and linuxulator. Also, I
noticed that the DRI and Glide support for the Voodoo4 and 5 has been
placed upon linux.3dfx.com, too bad they haven't released the tech docs
yet. Apparently, they are still pushing glide for all of us, so I will try
and add support once those tech docs are up.
binaries we just installed. This allows a future upgrade target to
install a new system without intermediate reboots and also
prevents conflicts for parallel make runs where we might exec a
binary that's being installed at the same time.
1. Correct FTP site for 4.0-stable snapshots and delete sentence
fragment immediately following.
[ not applicable to HEAD ]
2. Add FDDI section to table of contents (see #5 below) and add
one line of whitespace.
3. In userland section, document csh->tcsh, more->less, and
colorized ls.
4. In Ethernet section, do:
s/gigabit ethernet/Gigabit Ethernet/
s/fast ethernet/Fast Ethernet/
s/ethernet/Ethernet/
5. Pull DEC DEFPA/DEFEA *FDDI* cards out of the *Ethernet* section
and into their own second-level section.
6. Add missing period in section header in ATM section.
7. Tweak upgrading sectio with some new text, not sure if this is
much better though.
8. Add a blurb about the -stable mailing list.
[ changed to -current list in HEAD ]
PR: 20015
Submitted by: Bruce A. Mah <bmah@cisco.com>
other systems.
o Normalize copyright text.
o Clean up probe code function interfaces by passing around a single
structure of common arguments instead of passing "too many" args
in each function call.
o Add support for the AAA-131 as a SCSI adapter.
o Add support for the AHA-4944 courtesy of "Matthew N. Dodd" <winter@jurai.net
o Correct manual termination support for PCI cards. The bit definitions
for manual termination control in the SEEPROM were incorrect.
o Add support for extracting NVRAM information from SCB 2 for BIOSen
that use this mechanism to pass this data to OS drivers.
o Properly set the STPWLEVEL bit in PCI config space based on the
setting in an SEEPROM.
o Go back to useing 32byte SCBs for all controllers. The current
firmware allows us to embed 12byte cdbs on all controllers in
a 32byte SCB, and larger cdbs are rarely used, so it is a
better use of this space to offer more SCBs (32).
o Add support for U160 transfers.
o Add an idle loop executed during data transfers that prefetches
S/G segments on controllers that have a secondary DMA engine
(aic789X).
o Improve the performance of reselections by avoiding an extra
one byte DMA in the case of an SCB lookup miss for the reselecting
target. We now keep a 16byte "untagged target" array on the card
for dealing with untagged reselections. If the controller has
external SCB ram and can support 64byte SCBs, then we use an
"untagged target/lun" array to maximize concurrency. Without
external SCB ram, the controller is limited to one untagged
transaction per target, auto-request sense operations excluded.
o Correct the setup of the STPWEN bit in SXFRCTL1. This control
line is tri-stated until set to one, so set it to one and then
set it to the desired value.
o Add tagged queuing support to our target role implementation.
o Handle the common cases of the ignore wide residue message
in firmware.
o Add preliminary support for 39bit addressing.
o Add support for assembling on big-endian machines. Big-endian
support is not complete in the driver.
o Correctly remove SCBs in the waiting for selection queue when
freezing a device queue.
o Now that we understand more about the autoflush bug on the
aic7890, only use the workaround on devices that need it.
o Add a workaround for the "aic7890 hangs the system when you
attempt to pause it" problem. We can now pause the aic7890
safely regardless of what instruction it is executing.
Clean up the comments related to the high speed
sync rate table for SPI.
scsi_message.h:
Bring in some SCSI3 message terminology. All SCSI2 names
are still preserved for backwards compatibility.
Bring back the CAM_NEGOTIATE ccb flag. This flag indicates
that SPI transfer negotiation should occur concurrently with the
execution of this CCB. The flag is not yet used by the XPT but
is required for proper support of multi-initiator configurations
where topology scans cannot rely on a bus reset to invalidate
prior negotiations.
cam_xpt.c:
Don't allow DT transmission rates to be specified for devices
that don't have the DT feature listed in their inquiry data.
the building of the crunched binary.
I'll add examples when I add the post-include mechanism, since the
crunch.mk environment stomps on the pre-included crunch.inc's variables
at the moment.
objects, to simplify working with PicoBSD.
Add the ability to put make instructions in crunch.inc to pass to the
build process.
Now explicitly make the objects in our own object tree, since we want to
build the objects with our own defines, and allow this to occur in a
common object tree for all PicoBSD builds, if required. This is
controlled by the COMM_OBJ variable, for those who don't want this -
setting it to /usr/obj again will just pick up the objects from your
last make buildworld, as before.
for read-only src tree.
While I'm there:
1) Use kgzip, not kzip, since kzip certainly doesn't make bootable
kernels anymore. loader still isn't built separately, let alone without
forth support. This needs to be fixed.
2) Expand the mount/vnconfig examples to be the defacto way of making
sure the filesystems are mounted, unmounted, or not configured. This
needs more work.
3) quieten the build substantially, so errors are more prominent
4) Start of '-j' ability. Current style isn't quite in the correct
dependency format for this, but obvious mistakes (changing directories
in main shell) are fixed.
Approved by: grog, dwhite, luigi (no objections to me doing a makeover)
allocate a short port range in some alpha configurations.
Submitted by: "Andrew M. Miklic" <miklic@udlkern.fc.hp.com>,
Mark Abene <phiber@radicalmedia.com>
only does IPv4 as our syslogd only does IPv4. I dunno if the KAME
people have any plans for syslogd).
PR: 19821
Submitted by: Nick Hilliard <nick@iol.ie>
Reviewed by: sheldonh
