except for setting it. Also remove count from aha and replace it with
optional.
Also add commented out pccard lines for all the old card drivers.
They have to be commented out until they are converted because it
causes problems in NEWCARD.
valid) if BPF is missing.
The netgraph_bpf node forced bpf to be present, reflect that in the
options.
Stop doing a 'count bpf' - we provide stubs.
Since a handful of drivers still refer to "bpf.h", provide a more accurate
indication that the API is present always. (eg: netinet6)
parts: isa and pccard. The isa one is known to work with an IBM
EtherJet ISA card. The pccard one isn't known to work because the
EtherJet pccard I purchased recently arrived DOA :-(. I'll commit the
pccard.conf entry when the replacement card arrives.
I plan on MFC this in a week or two.
compiled under newcard yet. ep works just fine under newcard with the
missing ID matching code added (not committed yet):
ep0: <3Com 3c589 10Mbps Ethernet> at port 0x300-0x30f irq 9 function 0
config 1 on pccard1
ep0: Ethernet address 00:10:4b:df:48:57
this gives us several benefits, including:
* easier extensibility- new optional methods can be added to
ac97/mixer/channel classes without having to fixup every driver.
* forward compatibility for drivers, provided no new mandatory methods are
added.
- Break out the /dev/pci driver into a separate file.
- Kill the COMPAT_OLDPCI support.
- Make the EISA bridge attach a bit more like the old code; explicitly
check for the existence of eisa0/isa0 and only attach if they don't
already exist. Only make one bus_generic_attach() pass over the
bridge, once both busses are attached. Note that the stupid Intel
bridge's class is entirely unpredictable.
- Add prototypes and re-layout the core PCI modules in line with
current coding standards (not a major whitespace change, just moving
the module data to the top of the file).
- Remove redundant type-2 bridge support from the core PCI code; the
PCI-CardBus code does this itself internally. Remove the now
entirely redundant header-class-specific support, as well as the
secondary and subordinate bus number fields. These are bridge
attributes now.
- Add support for PCI Extended Capabilities.
- Add support for PCI Power Management. The interface currently
allows a driver to query and set the power state of a device.
- Add helper functions to allow drivers to enable/disable busmastering
and the decoding of I/O and memory ranges.
- Use PCI_SLOTMAX and PCI_FUNCMAX rather than magic numbers in some
places.
- Make the PCI-PCI bridge code a little more paranoid about valid
I/O and memory decodes.
- Add some more PCI register definitions for the command and status
registers. Correct another bogus definition for type-1 bridges.
but serves to work around some uncleanliness whereby the ISA bus is not
found on Alpha systems with PCI:EISA bridges due to the lack of EISA code
for the Alpha.
held and panic if so (conditional on witness).
- Change witness_list to return the number of locks held so this is easier.
- Add kern/syscalls.c to the kernel build if witness is defined so that the
panic message can contain the name of the offending system call.
- Add assertions that Giant and sched_lock are not held when returning from
a system call, which were missing for alpha and ia64.
- Make pccbb/cardbus kld loadable and unloadable.
- Make pccbb/cardbus use the power interface from pccard instead of inventing its own.
- some other minor fixes
using a cardbus based system with pccbb providing the pcic interface).
Something isn't quite right.. when the driver allocates and activates
its resources, the IO space that was requested reads as all zeros (versus
the original 0xff's as it normally is when there is no device responding).
Also, deactivate the resources before releasing them. OLDCARD doesn't
seem to care but NEWCARD/CARDBUS get rather unhappy if you release
a resource that hasn't been deactivated yet.
Make pcic_p.c only compile with oldcard kernels.
