the structure definitions come from NetBSD to make it easier to share card
definitions. The driver only acts as a shim between the pci bus and the
sio driver. Later pci parallel ports could also be supported through this
driver. Support for most single and multiport pci serial cards should be
as simple as adding its definition to pucdata.c
Tested with the following pci cards:
Moxa Industio CP-114, 4 port RS-232,RS-422/485
Syba Tech Ltd. PCI-4S2P-550-ECP, 4 port RS-232 + 2 parallel ports
Netmos NM9835 PCI-2S-550, 2 port RS-232
previous commit, it should always print due to lack of {} around the
second line in the if statement. The message should likely say
something more like "There's no hardware responding at this IRQ.
Device not present (or disbaled)," but that is too long. We generally
don't give elementary advise in device driver messages anyway. Be
that as it may, the problem with it printing all the time should be
corrected.
mutex releases to not require flags for the cases when preemption is
not allowed:
The purpose of the MTX_NOSWITCH and SWI_NOSWITCH flags is to prevent
switching to a higher priority thread on mutex releease and swi schedule,
respectively when that switch is not safe. Now that the critical section
API maintains a per-thread nesting count, the kernel can easily check
whether or not it should switch without relying on flags from the
programmer. This fixes a few bugs in that all current callers of
swi_sched() used SWI_NOSWITCH, when in fact, only the ones called from
fast interrupt handlers and the swi_sched of softclock needed this flag.
Note that to ensure that swi_sched()'s in clock and fast interrupt
handlers do not switch, these handlers have to be explicitly wrapped
in critical_enter/exit pairs. Presently, just wrapping the handlers is
sufficient, but in the future with the fully preemptive kernel, the
interrupt must be EOI'd before critical_exit() is called. (critical_exit()
can switch due to a deferred preemption in a fully preemptive kernel.)
I've tested the changes to the interrupt code on i386 and alpha. I have
not tested ia64, but the interrupt code is almost identical to the alpha
code, so I expect it will work fine. PowerPC and ARM do not yet have
interrupt code in the tree so they shouldn't be broken. Sparc64 is
broken, but that's been ok'd by jake and tmm who will be fixing the
interrupt code for sparc64 shortly.
Reviewed by: peter
Tested on: i386, alpha
(1) Don't attempt aquire the non-recursive lock sio_lock recursively.
Doing so caused unbounded recursion in some setups. E.g., if DDB,
BREAK_TO_DEBUGGER and WITNESS are configured; if the debugger is
entered using a break, then WITNESS will actually detect the invalid
recursion and will add to it attempting to print a message about it.
(2) Don't use sio_lock before it has been initialized. The old check
(sio_inited != 0) didn't work when sio_inited was boolean because
sio_inited was set too early, and became just wrong when sio_inited
was changed to a tri-state variable in rev.1.348.
Reported and fixed in another way by: fenner (1)
see people trip over it. Do not set the FIFO trigger to just before it
would otherwise overflow. Give it a little more slop so characters aren't
lost if the interrupt is delayed by other system activities.
MFC maybe: 7 days
allows us to move the sio softc data structure back into sio.c and
reduce the complexity of the non sio.c sio files.
Submitted by: bde
# I didn't fix the locking issues that bruce also submitted.
NEWCARD. Other patches may be reqiured to sio to prevent a hang on
eject. Also add commented out entries for sio_pccard.c in files.pc98
to match other architectures.
Submitted by: yamamoto shigeru-san
sio_pccard_detach to use new siodetach. Add an extra arg to sioprobe
to tell driver to probe/not probe the device for IRQs.
This incorporates most of Bruce's review material. I'm at a good
checkpoint, but there will be more to come based on bde's further
reviews.
Reviewed by: bde
Move sio from isa/sio.c to dev/sio/sio.c. The next step is to break
out the front end attachments, improve support for these parts on
different busses, and maybe, if we're lucky, merging in pc98 support.
It will also be MI and live in conf/files rather than files.*.
Approved by: bde
Tested with: i386, pc98
sio_lock has been initialized. This prevents the low level console
output (kernel printf) from clobbering the sio settings if the system
happens to be in the middle of comstart().
Note ALL MODULES MUST BE RECOMPILED
make the kernel aware that there are smaller units of scheduling than the
process. (but only allow one thread per process at this time).
This is functionally equivalent to teh previousl -current except
that there is a thread associated with each process.
Sorry john! (your next MFC will be a doosie!)
Reviewed by: peter@freebsd.org, dillon@freebsd.org
X-MFC after: ha ha ha ha
to properly clear the interrupt register on the no error case. Also,
set the mcr register to zero when we find we can't support the chip.
This fixes the hang on sio driver attach problem in the new pci pccard
code that some people have reported. At least on my machine. I'd
like to get this into 4.4.
Submitted by: bde
PR: kern/29742
MFC after: 1 day
the console device was open. At other times, the interrupts that
are used to detect the break signal or ~^B sequence were disabled,
so these events would not be noticed until the next open (e.g. the
next kernel printf). This was mainly a problem while there was no
getty running on the console, such as during bootup or shutdown.
For serial consoles with break-to-debugger support, we now enable
the generation of interrupts at attach time, and we leave them
enabled while the device is closed.
Reviewed by: bde (I've since made chages as per his suggestions)
I think bde even reviewed it once.
Also, change the name of ActionTEC pat to more generic Lucent Kermit
chip. Add stub for Xircom card. Add cardbus attachment too.
can be made userland-visible as <dev/ic/...>. Also, those files are
not supposed to contain any bus-specific details at all, so placing
them under .../isa/ has been a misnomer from the beginning.
The files in src/sys/dev/ic/ have been repo-copied from their old
location (this commit is a forced null commit there to record this
message).
other "system" header files.
Also help the deprecation of lockmgr.h by making it a sub-include of
sys/lock.h and removing sys/lockmgr.h form kernel .c files.
Sort sys/*.h includes where possible in affected files.
OK'ed by: bde (with reservations)
Some things needed bits of <i386/include/lock.h> - cy.c now has its
own (only) copy of the COM_(UN)LOCK() macros, and IMASK_(UN)LOCK()
has been moved to <i386/include/apic.h> (AKA <machine/apic.h>).
Reviewed by: jhb
- Use swi_* function names.
- Use void * to hold cookies to handlers instead of struct intrhand *.
- In sio.c, use 'driver_name' instead of "sio" as the name of the driver
lock to minimize diffs with cy(4).
mtx_enter(lock, type) becomes:
mtx_lock(lock) for sleep locks (MTX_DEF-initialized locks)
mtx_lock_spin(lock) for spin locks (MTX_SPIN-initialized)
similarily, for releasing a lock, we now have:
mtx_unlock(lock) for MTX_DEF and mtx_unlock_spin(lock) for MTX_SPIN.
We change the caller interface for the two different types of locks
because the semantics are entirely different for each case, and this
makes it explicitly clear and, at the same time, it rids us of the
extra `type' argument.
The enter->lock and exit->unlock change has been made with the idea
that we're "locking data" and not "entering locked code" in mind.
Further, remove all additional "flags" previously passed to the
lock acquire/release routines with the exception of two:
MTX_QUIET and MTX_NOSWITCH
The functionality of these flags is preserved and they can be passed
to the lock/unlock routines by calling the corresponding wrappers:
mtx_{lock, unlock}_flags(lock, flag(s)) and
mtx_{lock, unlock}_spin_flags(lock, flag(s)) for MTX_DEF and MTX_SPIN
locks, respectively.
Re-inline some lock acq/rel code; in the sleep lock case, we only
inline the _obtain_lock()s in order to ensure that the inlined code
fits into a cache line. In the spin lock case, we inline recursion and
actually only perform a function call if we need to spin. This change
has been made with the idea that we generally tend to avoid spin locks
and that also the spin locks that we do have and are heavily used
(i.e. sched_lock) do recurse, and therefore in an effort to reduce
function call overhead for some architectures (such as alpha), we
inline recursion for this case.
Create a new malloc type for the witness code and retire from using
the M_DEV type. The new type is called M_WITNESS and is only declared
if WITNESS is enabled.
Begin cleaning up some machdep/mutex.h code - specifically updated the
"optimized" inlined code in alpha/mutex.h and wrote MTX_LOCK_SPIN
and MTX_UNLOCK_SPIN asm macros for the i386/mutex.h as we presently
need those.
Finally, caught up to the interface changes in all sys code.
Contributors: jake, jhb, jasone (in no particular order)
going to hurt sio(4) performance for the time being. As we get closer to
release and have more of the kernel unlocked we can come back to doing
arcane optimizations to workaround the limitations of the sio hardware.
type of software interrupt. Roughly, what used to be a bit in spending
now maps to a swi thread. Each thread can have multiple handlers, just
like a hardware interrupt thread.
- Instead of using a bitmask of pending interrupts, we schedule the specific
software interrupt thread to run, so spending, NSWI, and the shandlers
array are no longer needed. We can now have an arbitrary number of
software interrupt threads. When you register a software interrupt
thread via sinthand_add(), you get back a struct intrhand that you pass
to sched_swi() when you wish to schedule your swi thread to run.
- Convert the name of 'struct intrec' to 'struct intrhand' as it is a bit
more intuitive. Also, prefix all the members of struct intrhand with
'ih_'.
- Make swi_net() a MI function since there is now no point in it being
MD.
Submitted by: cp
- Make softinterrupts (SWI's) almost completely MI, and divorce them
completely from the x86 hardware interrupt code.
- The ihandlers array is now gone. Instead, there is a MI shandlers array
that just contains SWI handlers.
- Most of the former machine/ipl.h files have moved to a new sys/ipl.h.
- Stub out all the spl*() functions on all architectures.
Submitted by: dfr
with #ifndef __alpha__/#endif
- Add function prototypes for functions used during the alpha console
probe and gdb port setup inside of #ifdef __alpha__/#endif.
newbus for referencing device interrupt handlers.
- Move the 'struct intrec' type which describes interrupt sources into
sys/interrupt.h instead of making it just be a x86 structure.
- Don't create 'ithd' and 'intrec' typedefs, instead, just use 'struct ithd'
and 'struct intrec'
- Move the code to translate new-bus interrupt flags into an interrupt thread
priority out of the x86 nexus code and into a MI ithread_priority()
function in sys/kern/kern_intr.c.
- Remove now-uneeded x86-specific headers from sys/dev/ata/ata-all.c and
sys/pci/pci_compat.c.
complain before that a suitable gdb port had not been setup because gdbdev
was NULL. This abuses the fact that the gdb port is hard-coded to the
address normally assigned to sio1 and thus hard-codes in sio1 as the gdb
port. Yuck.
siosetwater() function to its previous behavior of always disabling
interrupts and obtaining the com_lock before returning.
Requested by: bde (in principle)
include:
* Mutual exclusion is used instead of spl*(). See mutex(9). (Note: The
alpha port is still in transition and currently uses both.)
* Per-CPU idle processes.
* Interrupts are run in their own separate kernel threads and can be
preempted (i386 only).
Partially contributed by: BSDi (BSD/OS)
Submissions by (at least): cp, dfr, dillon, grog, jake, jhb, sheldonh
Implement the Solaris way to break into DDB over a serial console
instead of sending a break. Sending the character sequence
CR ~ ^b will break the kernel into DDB (if DDB is enabled).
Reviewed by: peter
more frequently than the core part of the sio driver, it might
be good to move the PnP IDs to sio_isapnp.h or something like
that.
PR: i386/18828
Submitted by: J.P. King <jpk28@cam.ac.uk>
doesn't support winmodems, softmodems, hcf or any other modem that
relies on the host to do any sort of soft control for any aspect of
the modem's function. There are two modems known to work:
3COM FaxModem PCI.
ActionTec 56k VoiceMessaging PCI Modem
and the following modem might work
Multitech PCI FaxModem (not sure about this)
and the serial pci cards might work too. I have neither these
hardware items so I can't add support for them.
Make the public interface more systematically named.
Remove the alternate method, it doesn't do any good, only ruins performance.
Add counters to profile the usage of the 8 access functions.
Apply the beer-ware to my code.
The weird +/- counts are caused by two repocopies behind the scenes:
kern/kern_clock.c -> kern/kern_tc.c
sys/time.h -> sys/timetc.h
(thanks peter!)
we get the com address. If so, we go ahead and return. Bruce thinks
there's a bug in the pccard layer that it terminates devices with
extreme prejustice rather than letting them deside for themselves when
to terminate (and he's likely right). This fix doesn't change that,
but instead works around it by checking for NULL pointers at more
places than before.
The detach routine still calls functions at interrupt level that
aren't reentrant. In theory this could cause a problem, but none
showed up in practice. Future versions should correct this problem,
likely by making the detach process a thread/process at the pccard
level. NEWCARD will do this, and the current pccard layer should
likely be modified to that as well, should it live long enough.
A few style nits of the same form that were in my original patch sent
off to bde were also fixed as part of this process. Mostly use of
!ptr and return ENOPARENS.
This should prevent a crash on suspend with an active ppp link as
well, but that wasn't tested.
Reviewed by: bde
Approved by: jkh
is responsible for this and this will lead to malloc 'freeing already
free' type panics. One was in the probe code, the other was in the
pccard eject? code.
Not explicitly approved by: jkh (but the first is fallout from subr_bus.c
rev 1.54 which was an approved commit, the second is the same problem)
1) Non-AST4 multiport cards were broken by bypassing the code that changes
`idev' to the multiport master device.
2) AST4 multiport cards apparently were broken by inverting the test for
the master device having an irq.
3) Error handling for nonexistent master devices was broken by removing a
check for a null pointer.
4) `int' error codes returned by bus_get_resource() were assigned directly
to the boolean variable com->no_irq. Probably harmless, since the
boolean is implemented as a u_char.
Submitted by: part 1) by Chris Radek <cradek@in221.inetnebr.com>
part 2) by yokota
Approved by: jkh
the same vendor and logical ID. The rest I am not sure whether they
are vendor or logical, but it won't hurt if I've put a vendor ID here
as merely will not match. These came from the old sio-pnp code, hence
the uncertainty about which ID it is.
ddb is entered. Don't refer to `in_Debugger' to see if we
are in the debugger. (The variable used to be static in Debugger()
and wasn't updated if ddb is entered via traps and panic anyway.)
- Don't refer to `in_Debugger'.
- Add `db_active' to i386/i386/db_interface.d (as in
alpha/alpha/db_interface.c).
- Remove cnpollc() stub from ddb/db_input.c.
- Add the dbctl function to syscons, pcvt, and sio. (The function for
pcvt and sio is noop at the moment.)
Jointly developed by: bde and me
(The final version was tweaked by me and not reviewed by bde. Thus,
if there is any error in this commit, that is entirely of mine, not
his.)
Some changes were obtained from: NetBSD
of these are bound to have a PNP05xx compatid, but there's no easy way to
tell. Since it's just an ID list and uses the pnp header's description
strings rather than encoding strings here, it doesn't seem to be too
expensive to err on the safe side.
o fix return type of sio_pccard_detach
o don't free softc in deatch, since that is done by newbus
o disconnect interrupt we used to have. Add cookie to com so that we can
tear down the interrupt on unload
o Set gone earlier, but likely doesn't matter
This makes sio pccards work again. Cards that are active when ejects may
not work (but they might, softc goes away quickly).
These changes are unreviewed by bde. I'll make any style changes he wants.
returns "0" on failure, which is indistinguishable from (say) irq 0. This
should stop a couple of stray messages that turn up.
Also, if a BUS_SETUP_INTR() fails with INTR_TYPE_FAST, try falling back to
a normal interrupt. This might help pccard folks with a shared slot
interrupt. This whole thing needs to be revisited.
problem.
o Create new timeout routine so we don't detach the card inside a ISR
but instead drop back to spl0 via a timeout of 0.
o Actually delete the child of the pccard device rather than just faking
it badly.
o Fix sio, ed and ep to have pccard detach routines that are int rather
than void.
o Fix ep and ed pccard detach routines to use if_detach rather than just
if_down. if_detach destroys the device, while if_down just marks it
down. In this incarnation of the pccard things, we map the disable
the slot action to detach the driver, which removes the driver from the
device tree. When that is done, a panic would soon follow as the
ifconfig tried to down the device.
Didn't fix:
o Should cache the pccard dev child's pointer in struct slot
o remove now unused parts of struct slot
o Any driver using softc after detach has been called. sio's softc used
to be statically allocated, so you could check sc->gone, but that is
now gone.
o Didn't remove gone from softc of drivers that use the old pccard method.
Didn't test:
o ed driver changes
o sio driver changes on pccards
o suspend (no laptop or apm support on my desktop)
Remove EXTRA_SIO/NSIOTOT and make it fully dynamic (from dev/sio/sio.c)
Make sio work for pccard here - pccardd doesn't activate interrupts
until after prove has succeeded.
Mark the initial reset of likely sio ports as broken as it depended on
config supplying a list of locations to probe, devices are now proved
standalone.
Optimize a bit of COM_NOAST4() logic.
Use bus_get_resource_start() etc rather than using isa-centric calls.
Reactivate the IIR_TXRDYBUG test, I've got a card here with it.
Try to be a bit smarter about activating interrupts (ie: don't panic
if polled)
Fix some style bugs that have crept in over time (there are still more).
by Peter Wemm, but I've not merged all the changes he sent to me yet.
This has not been reviewed by bde, so I'm committing to resolve any
issues he has with this when he returns from FreeBSD CON 99.
I've had four reports of this working for them. I've been able to
communicate to both my built in modem and a pccard modem with these
patches.
0x8024b04e) so that the cards description is used instead of overriding
it. While I'm here, add an ID for the SUP2080 and the SUP2030.
PR: kern/13983
Submitted by: Kurt D. Zeilenga <Kurt@OpenLDAP.Org> (SUP2030)
dfr (rest of change)
Reviewed by: dfr
Vendor ID SUP2480 (0x8024b04e), Serial Number 0x00001334
PnP Version 1.0, Vendor Version 0
Device Description: SupraExpress 56i Sp V.90
Reviewed by: dfr
have been there in the first place. A GENERIC kernel shrinks almost 1k.
Add a slightly different safetybelt under nostop for tty drivers.
Add some missing FreeBSD tags
fields in struct cdevsw:
d_stop moved to struct tty.
d_reset already unused.
d_devtotty linkage now provided by dev_t->si_tty.
These fields will be removed from struct cdevsw together with
d_params and d_maxio Real Soon Now.
The changes in this patch consist of:
initialize dev->si_tty in *_open()
initialize tty->t_stop
remove devtotty functions
rename ttpoll to ttypoll
a few adjustments to these changes in the generic code
a bump of __FreeBSD_version
add a couple of FreeBSD tags
rewrite the pccard attachment case. This is a work in progress, but
doesn't break the isa case.
I left the #if 0...#endif around the pccard stuff, at Peter's request,
so that normal users don't shoot themselves in the foot.
While I was here:
o Indent a comment to the right location
o Spell Unknown with a final 'n'.
Reviewed by: peter
new system is integrated with the ISA bus code more cleanly and allows
the future addition of more enumerators such as PnPBIOS and ACPI.
This commit also enables the new pcm driver since it is somewhat tied to
the new PnP code.
Diskslice/label code not yet handled.
Vinum, i4b, alpha, pc98 not dealt with (left to respective Maintainers)
Add the correct hook for devfs to kern_conf.c
The net result of this excercise is that a lot less files depends on DEVFS,
and devtoname() gets more sensible output in many cases.
A few drivers had minor additional cleanups performed relating to cdevsw
registration.
A few drivers don't register a cdevsw{} anymore, but only use make_dev().
- Split syscons source code into manageable chunks and reorganize
some of complicated functions.
- Many static variables are moved to the softc structure.
- Added a new key function, PREV. When this key is pressed, the vty
immediately before the current vty will become foreground. Analogue
to PREV, which is usually assigned to the PrntScrn key.
PR: kern/10113
Submitted by: Christian Weisgerber <naddy@mips.rhein-neckar.de>
- Modified the kernel console input function sccngetc() so that it
handles function keys properly.
- Reorganized the screen update routine.
- VT switching code is reorganized. It now should be slightly more
robust than before.
- Added the DEVICE_RESUME function so that syscons no longer hooks the
APM resume event directly.
- New kernel configuration options: SC_NO_CUTPASTE, SC_NO_FONT_LOADING,
SC_NO_HISTORY and SC_NO_SYSMOUSE.
Various parts of syscons can be omitted so that the kernel size is
reduced.
SC_PIXEL_MODE
Made the VESA 800x600 mode an option, rather than a standard part of
syscons.
SC_DISABLE_DDBKEY
Disables the `debug' key combination.
SC_ALT_MOUSE_IMAGE
Inverse the character cell at the mouse cursor position in the text
console, rather than drawing an arrow on the screen.
Submitted by: Nick Hibma (n_hibma@FreeBSD.ORG)
SC_DFLT_FONT
makeoptions "SC_DFLT_FONT=_font_name_"
Include the named font as the default font of syscons. 16-line,
14-line and 8-line font data will be compiled in. This option replaces
the existing STD8X16FONT option, which loads 16-line font data only.
- The VGA driver is split into /sys/dev/fb/vga.c and /sys/isa/vga_isa.c.
- The video driver provides a set of ioctl commands to manipulate the
frame buffer.
- New kernel configuration option: VGA_WIDTH90
Enables 90 column modes: 90x25, 90x30, 90x43, 90x50, 90x60. These
modes are mot always supported by the video card.
PR: i386/7510
Submitted by: kbyanc@freedomnet.com and alexv@sui.gda.itesm.mx.
- The header file machine/console.h is reorganized; its contents is now
split into sys/fbio.h, sys/kbio.h (a new file) and sys/consio.h
(another new file). machine/console.h is still maintained for
compatibility reasons.
- Kernel console selection/installation routines are fixed and
slightly rebumped so that it should now be possible to switch between
the interanl kernel console (sc or vt) and a remote kernel console
(sio) again, as it was in 2.x, 3.0 and 3.1.
- Screen savers and splash screen decoders
Because of the header file reorganization described above, screen
savers and splash screen decoders are slightly modified. After this
update, /sys/modules/syscons/saver.h is no longer necessary and is
removed.
Reformat and initialize correctly all "struct cdevsw".
Initialize the d_maj and d_bmaj fields.
The d_reset field was not removed, although it is never used.
I used a program to do most of this, so all the files now use the
same consistent format. Please keep it that way.
Vinum and i4b not modified, patches emailed to respective authors.
although this is pretty trivial. devclass_get_softc() is a tad more
expensive than the old com_addr() implementation. If Bruce is really
worried about the cost of this, it could always be changed so that the
softc pointer is stored in a local array again.
I'm not too happy about the result either, but at least it has less
chance of backfiring.
This particular feature could be called "a mess" without offending
anybody.
Virtualize bdevsw[] from cdevsw. bdevsw() is now an (inline)
function.
Join CDEV_MODULE and BDEV_MODULE to DEV_MODULE (please pay attention
to the order of the cmaj/bmaj arguments!)
Join CDEV_DRIVER_MODULE and BDEV_DRIVER_MODULE to DEV_DRIVER_MODULE
(ditto!)
(Next step will be to convert all bdev dev_t's to cdev dev_t's
before they get to do any damage^H^H^H^H^H^Hwork in the kernel.)
Mark the GDB port in the config file with flags 0x80. Currently
only the sio driver checks these flags and sets up a GDB port,
but adding similar code to other serial drivers would be easy.
For backward compatibility, if an sio port is marked as the console
and no port is marked as the gdb port, the GDB port will be mapped
to the console port. This hack should go away at some point.
1:
s/suser/suser_xxx/
2:
Add new function: suser(struct proc *), prototyped in <sys/proc.h>.
3:
s/suser_xxx(\([a-zA-Z0-9_]*\)->p_ucred, \&\1->p_acflag)/suser(\1)/
The remaining suser_xxx() calls will be scrutinized and dealt with
later.
There may be some unneeded #include <sys/cred.h>, but they are left
as an exercise for Bruce.
More changes to the suser() API will come along with the "jail" code.
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
* Update drivers to the latest version of the bus interface.
The ISA drivers' use of the new resource api is minimal. Garrett has
some much cleaner drivers which should be more easily shared between
i386 and alpha. This has only been tested on cia based machines. It
should work on lca and apecs but I might have broken something.
for the Lite2 fix for always returning EIO in dead_read().
Cleaned up the cdevswitch initializers for all tty drivers.
Removed explicit calls to ttsetwater() from all (tty) drivers. ttsetwater()
is now called centrally for opens, not just for parameter changes.
for 1 second's worth of input) and larger tty output buffers. The
interrupt-level buffers are still too small for speeds above 115200
bps (only a little too small for 230400 bps if RTS flow control is
enabled).
Don't call ttsetwater() explicitly in open(). It is now called for
the TTYDISC l_open() and should be static.
Don't attempt to register the cdevsw more than once.
instead of at compile time using ifdefs.
Use _swi_null instead of dummycamisr. CAM and dpt should call
register_swi() instead of hacking on ihandlers[] directly.
over from the probe are now expected for incompatible UARTs that
deliver IRQs as a strobe (low) instead of a level (high).
Discard events on going-away devices too. Endless loops may have
been possible when an active pccard was removed.
FreeBSD/alpha. The most significant item is to change the command
argument to ioctl functions from int to u_long. This change brings us
inline with various other BSD versions. Driver writers may like to
use (__FreeBSD_version == 300003) to detect this change.
The prototype FreeBSD/alpha machdep will follow in a couple of days
time.
miscconfigured case) if the port is the console. This fixes several
bugs:
- if all sioprobe()s failed, then the console driver followed null
pointers in cdevsw[].
- if the sioprobe() for the console failed but another sioprobe()
succeeded, then init hung early when the console couldn't be
opened.
- it was silly for the console to not be there after printing boot
messages on it.
Bugs introduced by this are hopefully no worse than old ones caused
by forcing the success of the `cn' level probe.
Only complain about an irq mismatch in the probe if the configured
irq doesn't become active, and then print the bitmap of irqs that
became active (including clock irqs) instead of just the first
(not including clock irqs).
Bugs reported by: msmith
a test of the irq number, and made failure of this test non-fatal.
Removed related unused complications for the APIC_IO case. Removed the
no-test3 flag.
Deverbosified the failure messages for the other tests. Removed the
per-port verbose flag - just use the general verbose flag.
but doesn't do much of anything with it. I added it to siopnp_ids[]
and it was found and recognized as a serial port.
PR: 6605
Reviewed by: phk
Submitted by: Dave Marquardt <marquard@zilker.net>
The differences Terrys patch and this patch are:
* Remove a lot of un-needed comments.
* Don't put l_hotchar at the front of stuct linesw, there is no need to.
* Use the #defines for the hotchar in the SLIP and PPP line disciplines
This introduce an xxxFS_BOOT for each of the rootable filesystems.
(Presently not required, but encouraged to allow a smooth move of option *FS
to opt_dontuse.h later.)
LFS is temporarily disabled, and will be re-enabled tomorrow.
- IIR_TXRDY is never off even if reading a IIR register.
- Know as PIAFS "Palido 321S", "DC-*S" oemed by Sharp corp.
2. Omiting a restrict probing if it's already probed by pccardd.
Note: Define a new id_flags as follows
0x40000 - NO PROBE (Already probed as serial)
0x80000 - Has a bogus IIR_TXRDY register
Sato Junichi <junichi@astec.co.jp>
Nrihiro Kumagai <kuma@slab.tnr.sharp.co.jp>
Hirao Tetsuya <ai.cs.fujitsu.co.jp>
Toshiharu Asai <asai@mbc.infoshere.or.jp>
Shin'ya Kumabuchi <kumabu@t3.rim.or.jp>
Freebsd-users-jp@jp.freebsd.orgbsd-nomads@ai.cs.fujitsu.co.jp
necessary to call it when the tty layer's output state has not been
changed, but siostop() sometimes changes the TS_BUSY state and then
calls comstart() mainly for its side effect of calling ttwwakeup().
use a Linker Set. Note, if a driver is loaded as an LKM if will have
to use the function call, but since none of the existing drivers
are loadable, this made things cleaner and boot messages nicer.
Obtained from: PAO-970616
* Kill individual drivers 'suspend' routines, since there's no simple/safe
way to suspend/resume a card w/out going through the complete probe
at initialization time.
* Default to using the apm_pccard_resume sysctl code, which basically
pretends the card was removed, and then re-inserted. Suspend/resume
is now 'emulated' with a fake insert/removal. (Hence we no longer
need the driver-specific suspend routines.)
follow.
* Rename/reorder all of the pccard structures, change many of the member
names to be descriptive, and follow more closely other 'bus' drivers
naming schemes.
* Rename a bunch of parameter and local variable names to be more
consistant in the code.
* Renamed the PCCARD 'crd' device to be the 'card' device
* KNF and make the code consistant where it was obvious.
* ifdef'd out some unused code
Distribute all but the most fundamental malloc types. This time I also
remembered the trick to making things static: Put "static" in front of
them.
A couple of finer points by: bde
internal modems. Currently detects a USR modem, and a couple Supra
modems... vendor id's for sio capabile cards welcomed...
document new option EXTRA_SIO that will increase sio's internal data
structures to support X more serial ports... these are used by the
PnP part of sio for attaching... If you don't have it specified, it
will default to 2... This is defaulted to 0 if you don't have PnP
compiled into your kernel...
also document that if you set the PnP flags (pnp x flags y) to 0x1 that
the modem will be refused to be recognized by the sio driver... this
is for people that want the traditional isa driver to probe and attach
the modem... (for keeping legacy sio numbering)
and hardware.
There is now another simple_lock around clock data/hardware accesses in
clock.c and microtime.s. It is my belief that this is the only area
sio/cy might stumble into during an unblocked INTerrupt. Thus I separated
the sio/cy code from the generic disable_intr()/enable_intr() routines.
Controlled by smptests.h: USE_COMLOCK, ON by default.
Add a simplelock to deal with disable_intr()/enable_intr() as used in UP kernel.
UP kernel expects that this is enough to guarantee exclusive access to
regions of code bracketed by these 2 functions.
Add a simplelock to bracket clock accesses in clock.c: clock_lock.
Help from: Bruce Evans <bde@zeta.org.au>
Several new fine-grained locks.
New FAST_INTR() methods:
- separate simplelock for FAST_INTR, no more giant lock.
- FAST_INTR()s no longer checks ipending on way out of ISR.
sio made MP-safe (I hope).
