are not allocated by the device driver. These resources should still appear
allocated from the system's perspective so that their assigned ranges are
not reused by other resource requests. The PCI bus driver has used a hack
to effect this for a while now where it uses rman_set_device() to assign
devices to the PCI bus when they are first encountered and later assigns
them to the actual device when a driver allocates a BAR. A few downsides of
this approach is that it results in somewhat confusing devinfo -r output as
well as not being very easily portable to other bus drivers.
This commit adds generic support for "reserved" resources to the resource
list API used by many bus drivers to manage the resources of child devices.
A resource may be reserved via resource_list_reserve(). This will allocate
the resource from the bus' parent without activating it.
resource_list_alloc() recognizes an attempt to allocate a reserved resource.
When this happens it activates the resource (if requested) and then returns
the reserved resource. Similarly, when a reserved resource is released via
resource_list_release(), it is deactivated (if it is active) and the
resource is then marked reserved again, but is left allocated from the
bus' parent. To completely remove a reserved resource, a bus driver may
use resource_list_unreserve(). A bus driver may use resource_list_busy()
to determine if a reserved resource is allocated by a child device or if
it can be unreserved.
The PCI bus driver has been changed to use this framework instead of
abusing rman_set_device() to keep track of reserved vs allocated resources.
Submitted by: imp (an older version many moons ago)
MFC after: 1 month
gptzfsboot. I got the segment and offset fields reversed in the structure,
but I also succeeded in crossing the assignments so the actual EDD packet
ended up correct.
MFC after: 1 week
safely allocate a heap region above 1MB. This enables {gpt,}zfsboot()
to allocate much larger buffers than before.
- Use a larger buffer (1MB instead of 128K) for temporary ZFS buffers. This
allows more reliable reading of compressed files in a raidz/raidz2 pool.
Submitted by: Matt Reimer mattjreimer of gmail
MFC after: 1 week
hw.bge.forced_collapse. hw.bge.forced_collapse affects all bge(4)
controllers on system which may not desirable behavior of the
sysctl node. Also allow the sysctl node could be modified at any
time.
Reviewed by: bde (initial version)
128 FIBs first and allocated more later if necessary. Remove now unused
definitions from the header file[1].
- Force sequential bus scanning. It seems parallel scanning is in fact
slower and causes more harm than good[1]. Adjust a comment to reflect that.
PR: kern/141269
Submitted by: Alexander Sack (asack at niksun dot com)[1]
Reviewed by: scottl
drivers. These add new hardware support, most importantly
the pch (i5 chipset) in the em driver. Also, both drivers
now have the simplified (and I hope improved) watchdog
code. The igb driver uses the new RX cleanup that I
first implemented in ixgbe.
em - version 6.9.24
igb - version 1.8.4
This adds new feature support for the 82599, a hardware
assist to LRO, doing this required a large revamp to the
RX cleanup code because the descriptor ring may not be
processed out of order, this necessitated the elimination
of global pointers.
Additionally, the RX routine now does not refresh mbufs
on every descriptor, rather it will do a range, and then
update the hardware pointer at that time. These are
performance oriented changes.
The TX side now has a cleaner simpler watchdog algorithm
as well, in TX cleanup a read of ticks is stored, that
can then be compared in local_timer to determine if
there is a hang.
Various other cleanups along the way, thanks to all who
have provided input and testing.
feature. These registers are reserved on controllers that have no
support for jumbo frame.
Only BCM5700 has mini ring so do not poke mini ring related
registers if controller is not BCM5700.
Reviewed by: marius
handler in brgphy(4) does not exist and brgphy(4) just resets the
PHY and returns EINVAL as it has no isolation handler. I also agree
on Marius's opinion that stop handler of every NIC driver seems to
be the wrong place for implementing PHY isolate/power down.
If we need PHY isolate/power down it should be implemented in
brgphy(4) and users should administratively down the PHY.
Reviewed by: marius
It makes MSI working there. Later (and cheaper) PCIe chips (3132/3531)
still randomly crashing system in few seconds of high MSI rates, generating
something inaporopriate, like NMI or "Fatal trap 30".
heap when using a range above 1MB.
Previously the loader would always use the last 3MB in the first memory
range above 1MB for the heap. However, this memory range is also where the
kernel and any modules are loaded. If this memory range is "small", then
using the high 3MB for the heap may not leave enough room for the kernel
and modules.
Now the loader will use any range below 4GB for the heap, and the logic to
choose the "high" heap region has moved into biosmem.c. It sets two
variables that the loader can use for a high heap if it desires. When a
high heap is enabled (BZIP2, FireWire, GPT, or ZFS), then the following
memory ranges are preferred for the heap in order from best to worst:
- The largest memory region in the SMAP with a start address greater than
1MB. The memory region must be at least 3MB in length. This leaves the
region starting at 1MB purely for use by the kernel and modules.
- The last 3MB of the memory region starting at 1MB if it is at least 3MB
in size. This matches the current behavior except that the current loader
would break horribly if the first region was not at least 3MB in size.
- The memory range from the end of the loader up to the 640k window. This
is the range the loader uses when none of the high-heap-requesting options
are enabled.
Tested by: hrs
MFC after: 1 week
- Cleanup kernel messages, mostly PMP.
- Took references on devices, while PMP reinitializes them, to not let them
go and distort freeze reference counting.
1. Fixups are always done on 512 byte chunks (in stead of sectors). This
is kind of stupid.
2. Conevrt between NTFS blocknumbers (the blocksize equals the media
sector size) and the bread() and getblk() blocknr (which are 512-byte
sized)
NB: this change should not affect ntfs for 512-byte sector sizes.
excluded, as it's used by MI code) and mode the sysctl variables from
pcpu_stats to pcpu_md.
Adjust all references accordingly.
While nearby, change the PCPU sysctl tree so that they match the CPU
device sysctl tree -- they are now children of a static node called
"machdep.cpu" and are named only with their cpu ID.
allocating MAXCPU VHPTs up-front. This allows us to max-out MAXCPU
without memory waste -- MAXCPU is now 32 for SMP kernels.
This change also eliminates the VHPT scaling based in the total
memory in the system. It's the workload that determines the best size
of the VHPT. The workload can be affected by the amount of memory,
but not necessarily. For example, there's no performance difference
between VHPT sizes of 256KB, 512KB and 1MB when building the LINT
kernel. This was observed with a system that has 8GB of memory.
By default the kernel will allocate a 1MB VHPT. The user can tune the
system with the "machdep.vhpt.log2size" tunable.
The ulog_login_pseudo(3) and ulog_logout_pseudo(3) interfaces provide a
functionality identical to what libutempter has to offer. Just transform
libutempter's calls into the before mentioned functions.
libutempter doesn't work with utmpx, so instead of fixing I thought the
easiest way would be to integrate this functionality. libutempter is
used by applications like xterm and the KDE libraries, so if I ever
change the underlying file format, these applications will keep working
automatically.
Also increase __FreeBSD_version to indicate the addition (as well as the
import of libulog).
Introduce ATA_CAM kernel option, turning ata(4) controller drivers into
cam(4) interface modules. When enabled, this options deprecates all ata(4)
peripheral drivers (ad, acd, ...) and interfaces and allows cam(4) drivers
(ada, cd, ...) and interfaces to be natively used instead.
As side effect of this, ata(4) mode setting code was completely rewritten
to make controller API more strict and permit above change. While doing
this, SATA revision was separated from PATA mode. It allows DMA-incapable
SATA devices to operate and makes hw.ata.atapi_dma tunable work again.
Also allow ata(4) controller drivers (except some specific or broken ones)
to handle larger data transfers. Previous constraint of 64K was artificial
and is not really required by PCI ATA BM specification or hardware.
Submitted by: nwitehorn (powerpc part)
unless pipe is idle. This should fix follwing issues:
- 'dummynet: OUCH! pipe should have been idle!' log messages.
- exceeding configured pipe bandwidth.
MFC after: 1 week
both to not panic when fsync(2) is called for fifo on zfs
filedescriptor, and to actually fsync fifo inode to permanent storage.
PR: kern/141177
Reviewed by: pjd
MFC after: 1 week
