I removed too many lines and a wrong pointer was accidentally passed down.
Tested by: Scott Allendorf (scott-allendorf at uiowa dot edu), kib
MFC after: 3 days
o Let OFW_INIT() and OF_init() return status value.
o Provide helper routines for 'compatible' property handling.
o Only compile OF and OFW code, which is relevant in FDT scenario.
o Other minor cosmetics
Reviewed by: imp
Sponsored by: The FreeBSD Foundation
whole bus (XPT_SCAN_BUS) and a single lun on that bus (XPT_SCAN_LUN).
It's less resource comsumptive than scanning a whole bus when the
caller knows only one target has changes.
Reviewed by: scsi@
Sponsored by: Panasas
MFC after: 1 month
The driver is stub. It just creates device entry and feeds
reassembled packets from hardware into it.
If in future we would port wsmouse(4) from NetBSD, or make
sysmouse(4) to support absolute motion events, then the driver
can be extended to act as system mouse. Meanwhile, it just
presents a /dev/uep0, that can be utilized by X driver, that
I am going to commit to ports tree soon.
The name for the driver is chosen to be the same as in NetBSD,
however, due to different USB stacks this driver isn't a port.
Make sure not to requeue freed mbuf in sge_start_locked(). This
should fix NULL pointer dereference panic.
Reported by: Nikolay Denev <ndenev <> gmail dot com>
Submitted by: jhb
device, make sure we have no real HPET device entry with same ID.
As side effect, it potentially allows several HPETs to be attached.
Use first of them for timecounting, rest (if ever present) could later
be used as event sources.
hook it up to ada(4) also. While at it, rename *ad_firmware_geom_adjust()
to *ata_disk_firmware_geom_adjust() etc now that these are no longer
limited to ad(4).
Reviewed by: mav
MFC after: 3 days
When not defining header split do not allocate mbufs,
this can be a BIG savings in the mbuf memory pool.
Also keep seperate dma maps for the header and
payload pieces when doing header split. The basis
of this code was a patch done a while ago by
yongari, thank you :)
A number of white space changes.
MFC: in a few days
free(9) and it can cause kernel panic when there are multiple graphics
controllers in the system.
Tested by: Brandon Gooch (jamesbrandongooch at gmail dot com)
MFC after: 3 days
firmware in order to take over control of the SMU. Without doing this,
the firmware background process doing fan control will run amok as we
take over the system and crash the management chip.
This is limited to these two machines because our kernel is heavily
dependent on firmware accesses, and so quiescing firmware can cause
nasty problems.
Powermac G5 systems. MSI and several other things are not presently
supported.
The U3/U4 internal device support portions of this change were contributed
by Andreas Tobler.
MFC after: 1 week
so ni_txrate returned 0 which is a invalid result.
- The fourth argument of ieee80211_ratectl_tx_complete() could be not
NULL.
Reported by: Gustau P?rez <gperez at entel.upc.edu>
Tested by: Gustau P?rez <gperez at entel.upc.edu>,
Ian FREISLICH <ianf at clue.co.za>
MFC after: 3 days
- add a moderation value to the Link vector
- allow disabling HW RSC on the 82599 if LRO
is not enabled.
- correct error in the stats code
- change optic type on the 82598 DA device
Thanks to Andrew Boyer for the changes.
RFA. Also drop frames that have either CRC error or alignment
error. Normally bad frames are not received at all. But controllers
running in promiscuous mode will receive bad frames. 82557 will
also receive bad frames to receive VLAN oversized frames.
While I'm here mark RNR condition if driver happen to see RNR in
RFA status and restart RU to receive frames again. Because driver
checks all received frames in RX loop, RNR condition could be set
in the middle of RX processing. Just relying on RNR interrupt was
not enough.
This change fixes "Memory modified after free" issue when fxp(4)
is running as a member of if_bridge(4).
Tested by: Larry Baird <lab <> gta dot com>
MFC after: 5 days
microframe slot was not in the smask. The problem was that the EHCI driver was
then thinking that the transfer was immediately complete in some cases. Which
could lead to freeze-like situations, which can be recovered by unplugging the
USB device.
Reported by: Richard Kolkovich
Submitted by: Hans Petter Selasky
