Previously, another thread could get a pointer to the
interface by scanning the system-wide list and sleep
on the global vlan mutex held by vlan_unconfig().
The interface was gone by the time the other thread
woke up.
In order to be able to call vlan_unconfig() on a detached
interface, remove the purely cosmetic bzero'ing of IF_LLADDR
from the function because a detached interface has no addresses.
Noticed by: a stress-testing script by maxim
Reviewed by: glebius
tested and then set. [1]
Reorganise things to eliminate this, we now ensure that enc0 can not be
destroyed which as the benefit of no longer needing to lock in
ipsec_filter and ipsec_bpf. The cloner will create one interface during the
init so we can guarantee that encif will be valid before any SPD entries are
added to ipsec.
Spotted by: glebius [1]
cards: the chips are all marked "RTL8111B", but they put stickers on the
back that say "RTL8168B/8111B". The manual says there's only one HWREV code
for both the 8111B and 8168B devices, which is 0x30000000, but the cards
they sent me actually report HWREV of 0x38000000. Deciding to trust the
hardware in front of me rather than a possibly incorrect manual (it wouldn't
be the first time the HWREVs were incorrectly documented), I changed the
8168 revision code. It turns out this was a mistake though: 0x30000000
really is a valid for the 8168.
There are two possible reasons for there to be two different HWREVs:
1) 0x30000000 is used only for the 8168B and 0x38000000 is only for
the 8111B.
2) There were 8111/8168 rev A devices which both used code 0x30000000,
and the 8111B/8168B both use 0x38000000.
The product list on the RealTek website doesn't mention the existence of
any 8168/8111 rev A chips being in production though, and I've never seen
one, so until I get clarification from RealTek, I'm going to assume that
0x30000000 is just for the 8168B and 0x38000000 is for the 8111B only.
So, the HWREV code for the 8168 has been put back to 0x30000000,
a new 8111 HWREV code has been added, and there are now separate
entries for recognizing both devices in the device list. This will
allow all devices to work, though if it turns out I'm wrong I may
need to change the ID strings
BCM5787 based NICs.
- Recognize BCM5703 B0 ASIC.
- Rewrite the jumbo capability matching macro, so that chips known
to work are listed there. [*]
[*] I'm still not sure about this. Probably more corrections
will be done to this macro after discussion with davidch@
and brad@OpenBSD.
Obtained from: OpenBSD (brad)
OpenBSD. This driver seems to give a small performance increase, and
should lead to better maintainability in the future.
The nForce Ethernet-specific hack in sys/i386/xbox/xbox.c is still
required, judging from dev/nfe/if_nfe.c. The condition it hacks will
almost certainly only occur on XBOX-es anyway, so it is best left there.
Approved by: imp (mentor)
one byte less than needed.
This is a RELENG_x_y candidate, since it fixes a problem with Oracle 10.
Noticed by: Dmitry Ganenko <dima@apk-inform.com>
Testcase by: Dmitry Ganenko <dima@apk-inform.com>
Reviewed by: des
Submitted by: rdivacky
Sponsored by: Google SoC 2006
MFC after: 1 week
- process state (idle, sleeping, running, ...) [1]
- the process group ID of the process which owns the connected tty
- some page fault stats
- time spend in kernel/userland
- priority/nice value
- starttime [1]
- memory/swap stats
- scheduling policy
Additionally add some new fields and correct some not filled out ones.
This brings us down to 15 dummy fields.
The fields marked with [1] are needed to get Oracle 10 running. The starttime
field is not completely right, since it displays the _same_ starttime for
_every_ process, but at least it is not 0 and Oracle accepts this.
This is a RELENG_x_y candidate.
Noticed by: Dmitry Ganenko <dima@apk-inform.com> [1]
Reviewed by: des, rdivacky
MFC after: 1 week
to a copied-in copy of the 'union semun' and a uioseg to indicate which
memory space the 'buf' pointer of the union points to. This is then used
in linux_semctl() and svr4_sys_semctl() to eliminate use of the stackgap.
- Mark linux_ipc() and svr4_sys_semsys() MPSAFE.
from going away. mount(2) is now MPSAFE.
- Expand the scope of Giant some in unmount(2) to protect the mp structure
(or rather, to handle concurrent unmount races) from going away.
umount(2) is now MPSAFE, as well as linux_umount() and linux_oldumount().
- nmount(2) and linux_mount() were already MPSAFE.
- For privileged processes safe two mutex operations.
We may want to consider if this is good idea to use SUSER_ALLOWJAIL here,
but for now I didn't wanted to change the original behaviour.
Reviewed by: rwatson
1. Make the caller responsible for performing pmap_install(). This reduces
the number of times that pmap_install() is performed by
pmap_enter_object() from twice per page to twice overall.
2. Don't block if pmap_find_pte() is unable to allocate a PTE. If it did
block, then it might wind up mapping a cache page. Specifically, if
pmap_enter_quick_locked() slept when called from pmap_enter_object(), the
page daemon could change an active or inactive page into a cache page just
before it was to be mapped.
3. Bail out of pmap_enter_quick_locked() if pv entries aren't plentiful.
In other words, don't force the allocation of a pv entry if they aren't
readily available.
Reviewed by: marcel@
pmap_copy() if the mapping is VM_INHERIT_SHARE. Suppose the mapping
is also wired. vmspace_fork() clears the wiring attributes in the vm
map entry but pmap_copy() copies the PG_W attribute in the PTE. I
don't think this is catastrophic. It blocks pmap_remove_pages() from
destroying the mapping and corrupts the pmap's wiring count.
This revision fixes the problem by changing pmap_copy() to clear the
PG_W attribute.
Reviewed by: tegge@
This driver was ported from OpenBSD by Shigeaki Tagashira
<shigeaki@se.hiroshima-u.ac.jp> and posted at
http://www.se.hiroshima-u.ac.jp/~shigeaki/software/freebsd-nfe.html
It was additionally cleaned up by me.
It is still a work-in-progress and thus is purposefully not in GENERIC.
And it conflicts with nve(4), so only one should be loaded.
encryption. There are two functions, a bpf tap which has a basic header with
the SPI number which our current tcpdump knows how to display, and handoff to
pfil(9) for packet filtering.
Obtained from: OpenBSD
Based on: kern/94829
No objections: arch, net
MFC after: 1 month
latter is a PCIe 10/100 chip.
Finally fix the EEPROM reading code so that we can access the EEPROMs on all
devices. In order to access the EEPROM, we must select 'EEPROM programming'
mode, and then set the EEPROM chip select bit. Previously, we were setting
both bits simultaneously, which doesn't work: they must be set in the
right sequence.
Always obtain the station address from the EEPROM, now that EEPROM
reading works correctly.
Make the TX interrupt moderation code based on the internal timer
optional and turned off by default.
Make the re_diag() routine conditional and off by default. When it is
on, only use it for the original 8169, which was the only device that
that really needed it.
Modify interrupt handling to use a fast interrupt handler and fast
taskqeueue.
Correct the rgephy driver so that it only applies the DSP fixup for
PHY revs 0 and 1. Later chips are fixed and don't need the fixup.
Make the rgephy driver advertise both 1000_FD and 1000_HD bits in
autoneg mode. A couple of the devices don't autoneg correctly unless
configured this way.
all of the module event handlers are MP safe yet, so always acquire Giant
for now when invoking module event handlers. Eventually we can add an
MPSAFE flag or some such and add appropriate locking to all module event
handlers.
o don't assign remote/local host/port information manually between provided
struct in_conninfo and struct syncache, bcopy() it instead
o rename sc_tsrecent to sc_tsreflect in struct syncache to better capture
the purpose of this field
o rename sc_request_r_scale to sc_requested_r_scale for ditto reasons
o fix IPSEC error case printf's to report correct function name
o in syncache_socket() only transpose enhanced tcp options parameters to
struct tcpcb when the inpcb doesn't has TF_NOOPT set
o in syncache_respond() reorder stack variables
o in syncache_respond() remove bogus KASSERT()
No functional changes.
Sponsored by: TCP/IP Optimization Fundraise 2005
o redefine the parameter 'is_syn' to 'flags', add TO_SYN flag and adjust its
usage accordingly
o update the comments to the tcp_dooptions() invocation in
tcp_input():after_listen to reflect reality
o move the logic checking the echoed timestamp out of tcp_dooptions() to the
only place that uses it next to the invocation described in the previous
item
o adjust parsing of TCPOPT_SACK_PERMITTED to use the same style as the others
o add comments in to struct tcpopt.to_flags #defines
No functional changes.
Sponsored by: TCP/IP Optimization Fundraise 2005
stations in power save: add a new q where mcast frames are stashed
and on beacon update (at DTIM) move frames from the mcast q to the
cabq and start it. This ensures the cabq is only manipulated in
one place.
Sponsored by: Hobnob
MFC after: 2 weeks
MBR should have only one entry of type 0xEE, consider protective MBR
to be one, that has at least one entry of type 0xEE covering the whole
unit. This makes GEOM_GPT compatible with disks partitioned by the
Apple's BootCamp.
Approved in principle by: marcel
MFC After: 1 month
in 1999, and there are changes to the sysctl names compared to PR,
according to that discussion. The description is in sys/conf/NOTES.
Lines in the GENERIC files are added in commented-out form.
I'll attach the test script I've used to PR.
PR: kern/14584
Submitted by: babkin
Don't enable/disable I/O space except for SAS adapters.
This fixes a problem with VMware 4.5 Workstation.
Fix an egregious bug introduced to target mode so it actually
will not panic when you first enable a lun.
Minor fixes:
Take more infor from port facts and configuration pages.
MFC after: 1 week
and don't panic.
This fix is different from the patch submitted as it not only prevents
a NULL-pointer dereference, but also skips some work in this case.
Noticed by: Dmitry Ganenko <dima@apk-inform.com>
Reviewed by: rdivacky (the original version as in emulation@)
MFC after: 1 week
Security: This is a RELENG_x_y candidate (local DoS).
Go ahead by: secteam (cperciva)
vm_page_startup(). As a result, we now only lookup the tunable once
instead of looking it up once for every physical page of memory in the
system. This cuts out about a 1 second or so delay in boot on x86
systems. The delay is much larger and more noticable on sun4v apparently.
Reported by: kmacy
MFC after: 1 week
with low nmbclusters, we tie up too many mbclusters in the NFS duplicate
request cache. This change limits the size of the dupreq cache to 1/2
the nmbclusters (and flaots in a range of [64, 2048]).
MFC after 2 weeks.
Reported by: Steve Kargl, David O'Brien
Tested by: Steve Kargl
infinite loop with net.inet6.ip6.fw.deny_unknown_exthdrs=0.
- Teach ipv6 and ipencap as they appear in an IPv4/IPv6 over IPv6
tunnel.
- Test the next extention header even when the routing header type
is unknown with net.inet6.ip6.fw.deny_unknown_exthdrs=0.
Found by: xcast-fan-club
MFC after: 1 week
protect all linker-related data structures including the contents of
linker file objects and the any linker class data as well. Considering how
rarely the linker is used I just went with the simple solution of
single-threading the whole thing rather than expending a lot of effor on
something more fine-grained and complex. Giant is still explicitly
acquired while registering and deregistering sysctl's as well as in the
elf linker class while calling kmupetext(). The rest of the linker runs
without Giant unless it has to acquire Giant while loading files from a
non-MPSAFE filesystem.
departing trunk so that we don't get into trouble later
by dereferencing a stale pointer to dead trunk's things.
Prodded by: oleg
Sponsored by: RiNet (Cronyx Plus LLC)
MFC after: 1 week
list.
- First remove from global list, then start destroying.
PR: kern/97679
Submitted by: Alex Lyashkov <shadow itt.net.ru>
Reviewed by: rwatson, brooks
linker for use in the linker class handlers. Move linker_add_class(),
linker_file_unload(), linker_load_dependencies(), and linker_make_file()
into this section.
- Add a new function linker_release_module() as a more intuitive complement
to linker_reference_module() that wraps linker_file_unload().
linker_release_module() can either take the module name and version info
passed to linker_reference_module() or it can accept the linker file
object returned by linker_reference_module().
VM_ALLOC_NORMAL instead of VM_ALLOC_SYSTEM when try is TRUE. In other
words, when get_pv_entry() is permitted to fail, it no longer tries as
hard to allocate a page.
Change pmap_enter_quick_locked() to fail rather than wait if it is
unable to allocate a page table page. This prevents a race between
pmap_enter_object() and the page daemon. Specifically, an inactive
page that is a successor to the page that was given to
pmap_enter_quick_locked() might become a cache page while
pmap_enter_quick_locked() waits and later pmap_enter_object() maps
the cache page violating the invariant that cache pages are never
mapped. Similarly, change
pmap_enter_quick_locked() to call pmap_try_insert_pv_entry() rather
than pmap_insert_entry(). Generally speaking,
pmap_enter_quick_locked() is used to create speculative mappings. So,
it should not try hard to allocate memory if free memory is scarce.
Add an assertion that the object containing m_start is locked in
pmap_enter_object(). Remove a similar assertion from
pmap_enter_quick_locked() because that function no longer accesses the
containing object.
Remove a stale comment.
Reviewed by: ups@
syscalls. This way there will be a log message printed to the console
(this time for real).
Note: UNIMPL should be used for syscalls we do not implement ever, e.g.
syscalls to load linux kernel modules.
Submitted by: rdivacky
Sponsored by: Goole SoC 2006
P4 IDs: 99600, 99602
file objects calling a user-specified predicate function on each object.
The iteration terminates either when the entire list has been iterated
over or the predicate function returns a non-zero value.
linker_file_foreach() returns the value returned by the last invocation
of the predicate function. It also accepts a void * context pointer that
is passed to the predicate function as well. Using an iterator function
avoids exposing linker internals to the rest of the kernel making locking
simpler.
- Use linker_file_foreach() instead of walking the list of linker files
manually to lookup ndis files in ndis(4).
- Use linker_file_foreach() to implement linker_hwpmc_list_objects().
number of banks, rows and columns the SDRAMC is programmed to access
to determine the RAM size for the board, rather than hard-wiring it to
be 32MB. My company's board with 64MB now probes correctly, as does
the KB9202 with only 32MB. This means that to detect the right memory
size, our boot loader must correctly initialize these values. This is
a fairly safe assumption because the boot loader has to initialize
SDRAM already, and it isn't really possible to change this register
after we've accessed SDRAM.
when we're about to call kdb_trap() because the latter MI
function can disable interrupts by itself now.
Pointed out by: bde
X-MFC remark: depends on kern/subr_kdb.c#1.18
Sponsored by: RiNet (Cronyx Plus LLC)
in setsockopt so that they can be compared correctly against negative
values. Passing in a negative value had a rather negative effect
on our socket code, making it impossible to open new sockets.
PR: 98858
Submitted by: James.Juran@baesystems.com
MFC after: 1 week
memory location for already existing/initialized mutexes. With random
data in the memory location this fails (ie. after a soft reboot).
Reported by: brueffer, YAMAMOTO Shigeru
Submitted by: YAMAMOTO Shigeru <shigeru-at-iij.ad.jp>
Use the method described in IA-32 Intel Architecture Software
Developer's Manual chapter 11.6.6 to get valid mxcsr bits,
use the mxcsr mask to clear invalid bits passed by user code.
order to - for example - apply firewall rules to a whole group of
interfaces. This is required for importing pf from OpenBSD 3.9
Obtained from: OpenBSD (with changes)
Discussed on: -net (back in April)
ACK the SYN as required by RFC793, rather than ignoring it. NetBSD
have had a similar change since 1999.
PR: 93236
Submitted by: Grant Edwards <grante@visi.com>
MFC after: 1 month
when the bit 22 is set to 1, CPUID with EAX=0 returns a maximum
value in EAX[7..0] of 3, when set to 0(default), CPUID with EAX=0
returns the number corresponding to the maximum standard function
supported. On my machine, BIOS sets the bit to 1 to make it to be
compatible with old OS, this causes dual-core Pentium-D (two
physical cores) to be identified as hyperthreading (two logical
cores) by function mp_topology().
offset or request size which is not a multiple of the sector size, make
sure that the bio is set to indicate that no data has actually been
transferred.
The result of this is that the file offset is no longer incremented for
these requests. The fact that the file offset was incremented broke
fdisk(8)'s probing of sector size for non-512 byte sector sizes.
Reviewed by: phk, cperciva
Submitted by: mdodd
MFC after: 2 weeks
for those upgrading from 4.x -> 5.x. It is therefore no longer
necessary because it is installed on 5.x and 6.x and one has to
upgrade from 6.x -> current, or at the very least 5.x (although not
supported, it can be made to work).
- Curitel PC5740 Wireless Modem (Verizon's PCMCIA card)
- Sierra MC5720 Wireless Modem (Built in to Thinkpad X60s)
The scanner in the PR is already supported.
PR: 98908
Submitted by: Michael Collette <metrol@metrol.net>
blinks by default. When the operating system (read: normally an Xbox
360) initializes the gamepad, the LED stops blinking.
Change our uhid code to do the same.
PR: 97169
Submitted by: Ed Schouten <ed@fxq.nl>
- Enable 4 automatic vchan's by default.
- Add some comments which provide ides/questions for improvement.
- Prefix some temporary sysctl's with an underscore to denote that it is not
an official API but a workaround until the real solution is implemented.
It is similar to debug.kdb.trap, except for it tries to cause a page fault
via a call to an invalid pointer. This can highlight differences between
a fault on data access vs. a fault on code call some CPUs might have.
This appeared as a test for a work \
Sponsored by: RiNet (Cronyx Plus LLC)
the return address on the stack and only then "dereferences" %pc.
Therefore, in the case of a call to an invalid address, we arrive
to the trap handler with the invalid value in tf_eip. This used
to prevent db_backtrace() from assigning the most recent and interesting
frame on the stack to the right spot in the right function, from
which the invalid call was attempted.
Try to detect and work around that by recovering the return address
from the stack.
The work-around requires the fault address be passed to db_backtrace().
Smuggle it as tf_err.
MFC after: 1 month
Sponsored by: RiNet (Cronyx Plus LLC)
The boot loader is supposed to leave this bit set to the right value
for the board. If this bit was set at attach time, use it to init the
config register correctly.
Note: this means the boot loader has to properly initialize it.
basically always violated) invariannts of soreceive(), which assume
that the first mbuf pointer in a receive socket buffer can't change
while the SB_LOCK sleepable lock is held on the socket buffer,
which is precisely what these functions do. No current protocols
invoke these functions, and removing them will help discourage them
from ever being used. I should have removed them years ago, but
lost track of it.
MFC after: 1 week
Prodded almost by accident by: peter
as possible for the syncache_add() case. The syncache timer no longer
aquires the tcpinfo lock and timeout/retransmit runs can happen in
parallel with bucket granularity.
On a P4 the additional locks cause a slight degression of 0.7% in tcp
connections per second. When IP and TCP input are deserialized and
can run in parallel this little overhead can be neglected. The syncookie
handling still leaves room for improvement and its random salts may be
moved to the syncache bucket head structures to remove the second lock
operation currently required for it. However this would be a more
involved change from the way syncookies work at the moment.
Reviewed by: rwatson
Tested by: rwatson, ps (earlier version)
Sponsored by: TCP/IP Optimization Fundraise 2005
yet. More commits to follow.
I got no response from the author, but since the driver is BSD licensed
I don't think he will complain. :-)
I got it from http://people.freebsd.org/~lofi/envy24.tar.gz
Written by: Katsurajima Naoto <raven@katsurajima.seya.yokohama.jp>
whether we have an IPv6 address. Write the term ID as 4 or
16 bytes depending on address type. This change matches the recent
OpenBSM change, and what Solaris does.
Obtained from: TrustedBSD Project
Approved by: rwatson (mentor)
prevents the unfortunate situation whereby one might kldload a firmware
module by hand and later kldunload it while a driver still has an open
reference to it.
MFC after: 1 week
Glanced at by: iedowse
frequency, quality and current value of each available time counter.
At the moment all of these are read-only, but it might make sense to
make some of these read-write in the future.
MFC after: 3 months
in parallel in several threads, one symbol lookup could
clear db_last_symtab when another one going to use it as
starting point for traversal.
Approved by: pjd (mentor)
MFC after: 1 month
Now GCC likes to stick a "mov %eax, %FOO" instruction before
"addl $BAR, %esp" if the function just called returns an int,
which is a very common case in the kernel.
Sponsored by: RiNet (Cronyx Plus LLC)
filesystem agnostic. We are not touching any file system specific functions
in this code path. Since we have a cache lock, there is really no need to
keep Giant around here.
This eliminates Giant acquisitions for any syscall which is auditing pathnames.
Discussed with: jeff
an explicit comment that it's needed for the linuxolator. This is not the
case anymore. For all other architectures there was only a "KEEP THIS".
I'm (and other people too) running a COMPAT_43-less kernel since it's not
necessary anymore for the linuxolator. Roman is running such a kernel for a
for longer time. No problems so far. And I doubt other (newer than ia32
or alpha) architectures really depend on it.
This may result in a small performance increase for some workloads.
If the removal of COMPAT_43 results in a not working program, please
recompile it and all dependencies and try again before reporting a
problem.
The only place where COMPAT_43 is needed (as in: does not compile without
it) is in the (outdated/not usable since too old) svr4 code.
Note: this does not remove the COMPAT_43TTY option.
Nagging by: rdivacky
- Add more device IDs, ASIC revisions and chip IDs.
- Rewrite a bit code that picks the description for device.
- Introduce several macros to shorten quirks for bugs and
features.[*]
- Use some magic values, that OpenBSD has successfully
possessed from Linux (Broadcom supplied) driver.
- Remove disabled code that tried to access VPD.
[*] The macro that matches Jumbo capable NICs is
rewritten to preserve our current behavior. I
need clarify whether our or theirs is correct.
PR: 68351 (and may be others)
Obtained from: OpenBSD, brad@ mostly
- 'tag' & 'untag' action parameters.
- 'tagged' & 'limit' rule options.
Rule examples:
pipe 1 tag tablearg ip from table(1) to any
allow ip from any to table(2) tagged tablearg
allow tcp from table(3) to any 25 setup limit src-addr tablearg
sbin/ipfw/ipfw2.c:
1) new macros
GET_UINT_ARG - support of 'tablearg' keyword, argument range checking.
PRINT_UINT_ARG - support of 'tablearg' keyword.
2) strtoport(): do not silently truncate/accept invalid port list expressions
like: '1,2-abc' or '1,2-3-4' or '1,2-3x4'. style(9) cleanup.
Approved by: glebius (mentor)
MFC after: 1 month
yield() and sched_yield() syscalls. Every scheduler has its own way
to relinquish cpu, the ULE and CORE schedulers have two internal run-
queues, a timesharing thread which calls yield() syscall should be
moved to inactive queue.
There is a race with the current locking scheme and removing
it should have no measurable performance impact.
This fixes page faults leading to panics in pmap_enter_quick_locked()
on amd64/i386.
Reviewed by: alc,jhb,peter,ps
!IFQ_DRV_IS_EMPTY(). Taking this into account, I re-structured the
transmit routine so as to avoid adding another if/then in the
critical path.
Thanks to brueffer for showing my how to test with altq/pf.
Found mapped cache page. Specifically, if cnt.v_free_count dips below
cnt.v_free_reserved after p_start has been set to a non-NULL value,
then vm_map_pmap_enter() would break out of the loop and incorrectly
call pmap_enter_object() for the remaining address range. To correct
this error, this revision truncates the address range so that
pmap_enter_object() will not map any cache pages.
In collaboration with: tegge@
Reported by: kris@
- Update the firmware to the latest released firmware
(1.4.3), which corresponds to the firmware in the
latest shipping drivers from Myricom. This firmware
fixes several bugs in the firmware's PCI-e implementation,
and it also changes the driver/firmware interface:
o TSO was added, and changed the format of the transmit
descriptors.
o The firmware no longer counts transmits descriptors,
but frames. So the driver needs to keep a count
of the number of frames sent.
o The weird interrupt strategy changed to a normal receive
return ring. This ring is much bigger, and we may be
able to support DEVICE_POLLING.
o Myricom's header files changed the name of firmware
related #define's and enums (s/_MCP_/FW_).
- Stopped spamming the console with lots of printfs unless
mxge_verbose (or bootverbose) is set.
- Made additional information available via sysctl, including
the results of a PCI-e DMA benchmark run at device reset.
- Decreased the excessively long timeouts when sending commands
from 2 seconds to 20ms.
Sponsored by: Myricom Inc.
KASSERT(ke->ke_runq == NULL) panic when the sched_add is recursively
called by maybe_preempt.
Reported by: Wojciech A. Koszek < dunstan at freebsd dot czest dot pl >
pointer to a zeroed, statically allocated bpf_if structure. This way the
LIST_EMPTY() macro will always return true. This allows us to remove the
additional unconditional memory reference for each packet in the fast path.
Discussed with: sam
we intend for the user to be able to unload them later via kldunload(2)
instead of calling linker_load_module() and then directly adjusting the
ref count on the linker file structure. This makes the resulting
consumer code simpler and cleaner and better hides the linker internals
making it possible to sanely lock the linker.
Giant down in it.
- Push Giant down in kern_kldunload() and reorganize it slightly to avoid
using gotos. Also, expose this function to the rest of the kernel.
- Use a 'struct kld_file_stat' on the stack to read data under the lock
and then do one copyout() w/o holding the lock at the end to push the
data out to userland.
linker_file_unload() instead of in the middle of a bunch of code for
the case of dropping the last reference to improve readability and sanity.
While I'm here, remove pointless goto's that were just jumping to a
return statement.
moving the typedef of bus_space_tag_t from sys/sparc64/include/bus.h
to sys/sparc64/include/_bus.h. This brings sparc64 in sync with the
other platforms and fixes the compilation of drivers which include
<sys/rman.h> before <machine/bus.h> after sys/sys/rman.h rev. 1.34.
- Remove the definition of bus_type_t from sys/sparc64/include/_bus.h
as it's unused since sys/sparc64/include/bus.h rev. 1.6 and
sys/sparc64/sparc64/bus_machdep.c rev. 1.3.
- Remove some pointless comments.
Update of syscall.master:
o Adding of several new dummy syscalls (268-310)
o Synchronization of amd64 syscall.master with i386 one
o Auditing added to amd64 syscall.master
o Change auditing type for lstat syscall (bugfix). [1]
P4-Changes: 98672, 98674
Noticed by: rwatson [1]
Sponsored by: Google SoC 2006
Submitted by: rdivacky
sockets:
1) A sender sends SCM_CREDS message to a reciever, struct cmsgcred;
2) A reciever sets LOCAL_CREDS socket option and gets sender
credentials in control message, struct sockcred.
Both methods use the same control message type SCM_CREDS with the
same control message level SOL_SOCKET, so they are indistinguishable
for the receiver. A difference in struct cmsgcred and struct sockcred
layouts may lead to unwanted effects.
Now for sockets with LOCAL_CREDS option remove all previous linked
SCM_CREDS control messages and then add a control message with
struct sockcred so the process specifically asked for the peer
credentials by LOCAL_CREDS option always gets struct sockcred.
PR: kern/90800
Submitted by: Andrey Simonenko
Regres. tests: tools/regression/sockets/unix_cmsg/
MFC after: 1 month
the description so we don't have to do any more queries. Disable the
event query code until it figured out since but it is similar to the
AEN detail so we should be able to get that working.
s/myri10ge/mxge/g replacement in the myri10ge files. A few contuation
lines were joined because of the regained columns.
- Hook the mxge driver back to the build.
I picked it up again. The scheduler is forked from ULE, but the
algorithm to detect an interactive process is almost completely
different with ULE, it comes from Linux paper "Understanding the
Linux 2.6.8.1 CPU Scheduler", although I still use same word
"score" as a priority boost in ULE scheduler.
Briefly, the scheduler has following characteristic:
1. Timesharing process's nice value is seriously respected,
timeslice and interaction detecting algorithm are based
on nice value.
2. per-cpu scheduling queue and load balancing.
3. O(1) scheduling.
4. Some cpu affinity code in wakeup path.
5. Support POSIX SCHED_FIFO and SCHED_RR.
Unlike scheduler 4BSD and ULE which using fuzzy RQ_PPQ, the scheduler
uses 256 priority queues. Unlike ULE which using pull and push, the
scheduelr uses pull method, the main reason is to let relative idle
cpu do the work, but current the whole scheduler is protected by the
big sched_lock, so the benefit is not visible, it really can be worse
than nothing because all other cpu are locked out when we are doing
balancing work, which the 4BSD scheduelr does not have this problem.
The scheduler does not support hyperthreading very well, in fact,
the scheduler does not make the difference between physical CPU and
logical CPU, this should be improved in feature. The scheduler has
priority inversion problem on MP machine, it is not good for
realtime scheduling, it can cause realtime process starving.
As a result, it seems the MySQL super-smack runs better on my
Pentium-D machine when using libthr, despite on UP or SMP kernel.
- Try hard to calculate a safe sp, so that the stack doesn't get smashed
while uncompressing or relocating the kernel.
- Bring in code needed to calculate the cacheline size etc, needed for
arm9_idcache_wbinv_all.
for CBUS-PNP cards there) by default, as there are no amd64 and sparc64
machines with ISA slots and which therefore could make use of this code
known to exist. For sparc64 this additionally allows to get rid of the
compat shims for in{b,w,l}()/out{b,w,l}() etc and the associated hacks.
OK'ed by: imp, peter
o Implement a bunch of sysctl's to report the information
that's now always reported. Mvoe reporting of that info
to bootverbose, but maybe it can go away entirely.
dev.ed.X.type: string name
dev.ed.X.TxMem: amount of memory used for tx side of the card
dev.ed.X.RxMem: amount of memory used for rx side of the card
dev.ed.X.Mem: Total amount of mem on card.
o Better comments about where NE-2000 (and clones) gets their MAC
address from.
the arm to compile without all the extras that don't appear, at least
not in the flavors of ARM I deal with. This helps us save about 100k.
If I've botched the available devices on a platform, please let me
know and I'll correct ASAP.
systems. Introduce a new sysctl "hw.acpi.disable_on_reboot" that allows
users to re-enable the old behavior in case it's needed for some systems.
We never disable in the power-off path.
Original approach submitted by Alexander Logvinov <abuse@akavia.ru> with
reworking by Jung-uk Kim and myself.
current interface with the machine-independent layer. Without this change,
the page daemon would only have been awakened the first time that the
number of pv entries went above the high water mark, not each time.
S_IFDIR when making a directory
S_IFLNK when making a symbolic link
S_IFIFO when making a pipe
xfs_ialloc() checks this field for these flags when figuring
out whether to make a directory, make a symbolic link or make a pipe.
firmware_get() will not work while resuming. Note that we can't
simply drop the FIRMWARE_UNLOAD flag, because that will result in
a firmware image that can never be unloaded by the user since the
firmware subsystem will hold a linker reference to it (it's not
clear that firmware_put() without FIRMWARE_UNLOAD ever does quite
what you'd want).
with firmware_unregister(). Previously when the last driver reference
had been dropped we would clear the list entry under the assumption
that the firmware module was about to be unloaded, but this was not
true if the firmware image had been loaded manually with kldload.
This makes it possible to manually kldload firmware images as a
workaround for drivers such as ipw that attempt to load firmware
while resuming after a suspend.
Reviewed by: mlaier (an earlier version of the patch)
- Move sonewconn(), which creates new sockets for incoming connections on
listen sockets, so that all socket allocate code is together in
uipc_socket.c.
- Move 'maxsockets' and associated sysctls to uipc_socket.c with the
socket allocation code.
- Move kern.ipc sysctl node to uipc_socket.c, add a SYSCTL_DECL() for it
to sysctl.h and remove lots of scattered implementations in various
IPC modules.
- Sort sodealloc() after soalloc() in uipc_socket.c for dependency order
reasons. Statisticize soalloc() and sodealloc() as they are now
required only in uipc_socket.c, and are internal to the socket
implementation.
After this change, socket allocation and deallocation is entirely
centralized in one file, and uipc_socket2.c consists entirely of socket
buffer manipulation and default protocol switch functions.
MFC after: 1 month
not be necessary but might be helpful and at least reduce fragmentation.
* Add an assert to detect if the wakecode ever grows too big. We include
1 KB for stack, which should be more than enough also.
* Remove unnecessary initialization of static variables.
* Add comments and a bootverbose print giving the page phys address.
to 4. There is no need to be more strict at assembly time since we copy
the code anyway to a private page.
* Clear the direction flag and eflags. Probably not necessary but it won't
hurt to be safe.
* Add prefixes to all instructions to prevent any assembler mistakes.
* Remove zeroing of eax - edi. We use those registers immediately after
to transfer values to protected mode so this was pointless.
* Update comments to reflect info found during code review.
get a consistent snapshot, as well as get consistent values (i.e.,
that p_comm is properly nul-terminated).
Perforce CID: 98824
Obtained from: TrustedBSD Project
Map the device memory belonging to resources of type SYS_RES_MEMORY into
KVA upon activation so that rman_get_virtual() works as expected.
- In sbus_alloc_resource() checking whether toffs is 0 as an indication
that no applicable child range was found isn't appropriate as it's
perfectly valid for the requested SYS_RES_MEMORY resource to start at
the beginning of a child range. So check for the RMAN still being NULL
instead.
- As a minor runtime speed optimization break out of the loop where we
search for the applicable child range in sbus_alloc_resource() as soon
as it's found.
- Let sbus_setup_intr() return ENOMEM rather than 0 if it can't allocate
memory for the interrupt clearing info.
- Actually do what the comment in sbus_setup_intr() says and disable the
respective interrupt while fiddling with it.
- Remove some superfluous INTVEC() around inr, which already only contains
the interrupt vector, in sbus_setup_intr().
- While here, fix a style(9) bug in sbus_setup_intr() (don't use function
calls in initializers).
The first two changes are required for a CG6 driver.
MFC after: 2 weeks
- Removed updates to if_ibytes, if_obytes, if_imcasts, and if_omcasts.
These should not be handled by the driver.
- Add code to handle excessively fragmented mbufs when mapping TX frames.
Reviewed by: ps
Approved by: ps (mentor)
MFC after: 1 week
* Add hw.acpi.resume_beep tunable and sysctl, default to 0. Beeps the PC
speaker soon after waking to diagnose whether the wakeup code is even
getting run before other drivers possibly hang the system. To stop the beep,
cause another beep (i.e. keyboard bell). Submitted by takawata@, I changed
the frequency to be lower.
* Use 4096 instead of 4 byte alignment. Might be useful although doesn't
seem to be necessary.
* Remove a useless assignment to acpi_reset_video. It was overwritten by
the default sysctl value anyway.
