chips where setting the FAILDIS bit is not effective. While here,
try again to make it clear that reported parity errors indicate
a failure of some PCI device *other than* the aic7xxx controller.
timer reset rather than the timer of an SCB still pending on the
controller after recovery completed. This should correct timeout
loops seen in the field.
has been removed. It has been replaced by hw.pci.do_power_nodriver
and hw.pci.do_power_resume. The former defaults to 0 while the latter
defaults to 1.
When do_powerstate was set to 0, it broke suspend/resume for a lot of
people as an unintended consequence. This change will only affect the
areas that were intended to affect. This change will have no effect on
servers, but will help laptops quite a bit.
MFC After: 3 days.
The FXP_SCR_FLOWCONTROL registers is at offset 0x19, but 2 bytes wide.
It cannot be read as a word without causing a panic on architectures
that enforce strict alignment.
MFC after: 3 days
in an IBSS. Store ids directly into ieee80211_node's instead of managing
our own private association table. Idea and code by Sam Leffler.
Submitted by: sam
MFC after: 5 days
Remove md_mtx.
Remove GIANT from the mdctl device driver and avoid DROP_GIANT,
PICKUP_GIANT and geom events since we can call into GEOM directly
now.
Pick up Giant around vn_close().
Apply an exclusive sx around mdctls ioctl and preloading to protect
lists etc..
Don't initialize our lock (md_mtx or md_sx) from a
SYSINIT when there is a perfectly good pair of _fini/_init
functions to do it from.
Prune any final fractional sector from the mediasize to
keep GEOM happy.
Cleanups:
Unify MDIOVERSION check in (x)mdctlioctl()
Add pointer to start() routine to softc to eliminate a switch{}
Inline guts of mddetach().
Always pass error pointer to mdnew(), simplify implementation.
could get an interrupt after we free the ifp, and the interrupt
handler depended on the ifp being still alive, this could, in theory,
cause a crash. Eliminate this possibility by moving the if_free to
after the bus_teardown_intr() call.
o eliminate the ED_NO_MIIBUS option. Now, you need miibus to use ed with
pccard. If you have an old ISA or PCI card w/o a miibus, then you'll still
be able to use the ed driver w/o miibus in the kernel. If you have pccard
you'll need mii now. Most pccards these days have miibus, and many
cards have ISSUES if you don't attach miibus. issues I don't want to
constantly rediagnose.
- Add new media_ioctl, mediachg and tick function pointers. The core
driver will call these if they aren't NULL, or return an error if they
are.
- migrate remaining mii code into if_ed_pccard.
o include some notes from my datasheet fishing. this may allow us to
get media status from some pccards.
o Fix one bug that's common to many drivers. call if_free(ifp) after
we tear down the interrupt. ed_intr() depends on ifp being there and
freeing it while interrupts can still happen is, ummm, bad.
the switch statement in order to make this driver more like other
Ethernet NIC drivers.
- In gem_attach() call gem_stop() in addition to gem_reset() to make
sure the chip actually is stopped and not just reset.
- In gem_stop() also stop the gem_rint_timeout() callout in case the
driver is compiled with GEM_RINT_TIMEOUT defined.
Merge some locking improvements from hme(4):
- Use callout_init_mtx() to close races between gem_stop() and gem_tick()
as weel as gem_stop() and gem_rint() in case the driver is compiled
with GEM_RINT_TIMEOUT defined.
- Use the driver lock instead of Giant in a bus dma callback.
- Lock the driver lock around mii operations.
- Cleanup locking in gem_ioctl().
- Remove redundant assertions that the driver lock is not held in
gem_attach() and gem_detach() since mtx_lock() will assert that
already since the driver lock is not recursive.
- Add callout_drain()'s to gem_detach() after calling gem_stop() to make
sure that if softclock is running on another CPU and is blocked on our
driver lock, we will wait until it has acquired the lock, seen that it
was cancelled, dropped the lock, and awakened us so that we can safely
destroy the mutex.
Synchronise with NetBSD upto rev 1.19:
- Allow 32 chars in the saved vendor string.
- Some NetBSD-only changes.
- Some missing parts (define, variable).
ehci_pci.c:
Add vendor ids for ATI and Philips.
Add identification strings for the following:
o ALi's M5239
o AMD 8111
o ATI SB200, SB400
o Intel 6300ESB, ICH4, ICH5, ICH7
o NVIDIA nForce 2, nForce 3, nForce 4
o Philips ISP156x
ehcireg.h:
We're at the same level as rev 1.18 from NetBSD.
usb_port.h:
NetBSD/OpenBSD specific things
Obtained from: NetBSD via DragonFly
No comment from: usb@
o Allow association with APs that do not broadcast SSID (with hints from
Nick Hudson and Hajimu Umemoto).
o IFQ_DRV_PREPEND mbuf when h/w ring is full so it can be sent later.
o Increment if_oerrors when appropriate.
o Did some cleanup while I'm here.
MFC after: 1 day
the Linux driver, since specs are unavailable. Many thanks to Adam Kirchhoff
for multiple useful testing cycles, and Ralf Wostrack for the final fix to get
it working.
PR: i386/75251
Submitted by: anholt
9200 according to one responder. The primary issue was not setting some bits
to say that the entries were active, but also fix one place where some memory
wasn't being used as volatile as it should. While here, change some use of ffs
to a relatively short case statement, to make it more obvious what's going on.
PR: kern/71638, kern/72372, kern/71547?
Submitted by: Andrew J. Caines <A.J.Caines@halplant.com>,
Robin Schoonover <end@endif.cjb.net>,
Jason Henson <jason@ec.rr.com>
