setting in the igb and em driver. This was necessitated by
a shared code change that I was given late in the game, a data
type changed from bool to int, in the last update I dealt with
it by a cast, but it was pointed out (thanks jhb) that there
was a potential problem with this. John suggested this safer
approach, and it is fine with me...
MFC after:2 days (to catch the 9.1 update)
inactive queue, unless busy page is found.
Dropping the mutex often should allow the other lock acquires to
proceed without waiting for whole inactive scan to finish. On machines
with lot of physical memory scan often need to iterate a lot before it
finishes or finds a page which requires laundring, causing high
latency for other lock waiters.
Suggested and reviewed by: alc
MFC after: 3 weeks
is an error set on the provider. With GEOM resizing, class can become
orphaned when it doesn't implement resize() method and the provider size
decreases.
Reviewed by: mav
Sponsored by: FreeBSD Foundation
although by default only C1 is enabled (cx_lowest=0) and enabling deeper
states goes through acpi_cpu_set_cx_lowest which re-evaluates cpu_non_c3
MFC after: 2 weeks
cpu_non_c3 is already evaluated in acpi_cpu_cx_cst and in
acpi_cpu_set_cx_lowest.
Besides acpi_cpu_cx_list is not protected by any locking.
As a result also move setting of cpu_can_deep_sleep to more appropriate
places.
MFC after: 2 weeks
before VM has been initialized. This includes:
1. Replacing pmap_steal_memory(),
2. Replace the handcrafted logic to allocate a naturally aligned VHPT,
3. Properly allocate the DPCPU for the BSP.
Ad 3: Appending the DPCPU to kernend worked as long as we wouldn't
cross into the next PBVM page. If we were to cross into the next
page, then there wouldn't be a PTE entry on the page table for it
and we would end up with a MCA following a page fault. As such,
this commit fixes MCAs occasionally seen.
arm platform. Add all the atmel boards to the ATMEL kernel for
testing purposes. Until boot loader arg parsing of baord type
is done, this won't actually be able to do the runtime selection.
100 bytes from the binary with silly tricks. Hope to get this small
enough to run on the models that have 4k SRAM. We are close compiled
for the at91rm9200, but still need to trim for the target.
correctly. We now iterate the EFI memory descriptors once and collect all
the information in a single pass. This includes:
1. The I/O port base address,
2. The PAL memory region. Have the physmem API track this.
3. Memory descriptors of memory we can't use, like bad memory, runtime
services code & data, etc. Have the physmem API track these.
4. memory descriptors of memory we can use or re-use, such as free
memory, boot time services code & data, loader code & data, etc.
These are added by the physmem API.
Since the PBVM page table and pages are in memory described as loader
data, inform the physmem API of chunks that need to be delated from the
available physical memory.
While here, remove Maxmem and replace it with the better named paddr_max.
Maxmem was defined as physmem, which is generally wrong. Now, paddr_max
is properly defined as the largesty physical address.
The upshot of all this is that:
1. We properly determine realmem.
2. We maximize physmem by re-using memory where possible.
3. We remove complexity from ia64_init() in machdep.c.
4. Remove confusion about realmem, physmem & Maxmem.
The new ia64_physmem_alloc() is to replace pmap_steal_memory() in pmap.c,
as well as replace the handcrafted allocation of the VHPT for the BSP in
pmap_bootstrap() in pmap.c. This is step 2 and addresses the manipulation
of phys_avail after it is being created.
This partially reverts some changes from r237448 that are causing
breakage when resizing under bin/sh .
Reverted changes from NetBSD are:
Mar 10 20:46:15 2009 - editline.3 read.c
make el_gets set the count to -1 on error to distinguish between EOF and
error.
Feb 19 15:20:22 2009 - read.c sig.c sig.h
reset and redraw on sigcont. From Anon Ymous.
Feb 15 21:24:13 2009
don't restart on EINTR, instead return NULL immediately. From Anon Ymous
PR: 169603
Reported by: Peter Jeremy, David Shao
MFC after: 3 days
Don't use Maxmem when the amount of memory is meant. Use realmem instead.
Maxmem is not only a MD variable, it represents the highest physical memory
address in use. On systems where memory is sparsely layed-out the highest
memory address and the amount of memory are not interchangeable. Scaling the
AGP aperture based on the actual amount of memory (= realmem) rather than
the available memory (= physmem) makes sure there's consistent behaviour
across architectures.
agp_i810.c:
While arguably the use of Maxmem can be considered correct, replace its use
with realmem anyway. agp_i810.c is specific to amd64, i386 & pc98, which
have a dense physical memory layout. Avoiding Maxmem here is done with an
eye on copy-n-paste behaviour in general and to avoid confusion caused by
using realmem in agp.c and Maxmem in agp_i810.c.
In both cases, remove the inclusion of md_var.h
Update DTrace disassembler accordingly. The code to treat the prefixes
as null prefixes was already in place.
Although in practice compilers seem to generate only cs-prefix for use
in long NOPs, the same treatment is applied to all of cs, ds, es, ss for
consistency.
Reported by: emaste
Tested by: emaste
Obtained from: Illumos commit 13442:4adbe6de60c8 (+ local changes)
MFC after: 5 days
adding appropriate table entries, the assembler had to be adjusted as
these are the first non-SSE instructions to use a 3-byte opcode (and a
mandatory prefix to boot).
MFC after: 1 month
- Add generic support for opcodes that are escape bytes used for
multi-byte opcodes (such as the 0x0f prefix). Use this to replace
the hard-coded 0x0f special case and add support for three-byte
opcodes that use the 0x0f38 prefix.
- Decode all Intel VMX instructions. invept and invvpid in particular are
three-byte opcodes that use the 0x0f38 escape prefix.
- Rework how the special 'SDEP' size flag works such that the default
instruction name (i_name) is the instruction when the data size
prefix (0x66) is not specified, and the alternate name in i_extra is
used when the prefix is included.
- Add a new 'ADEP' size flag similar to 'SDEP' except that it chooses
between i_name and i_extra based on the address size prefix (0x67).
Use this to fix the decoding for jrcxz vs jecxz which is determined
by the address size prefix, not the operand size prefix. Also, jcxz
is not possible in 64-bit mode, but jrcxz is the default instruction
for that opcode.
- Add support for handling instructions that have a mandatory 'rep'
prefix (this means not outputting the 'repe ' prefix until determining
if it is used as part of an opcode). Make 'pause' less of a special
case this way.
- Decode 'cmpxchg16b' and 'cdqe' which are variants of other instructions
but with a REX.W prefix.
MFC after: 1 month
Set a flag and allow worker threads to finish upon ^C, instead of
immediately cancelling them, so that final packet count and rate
stats can be displayed.
"Reserved by Microsoft" in the standard PNP ID table, but has been seen
in the wild on at least one laptop.
PR: kern/169571
Submitted by: Matthias Apitz guru unixarea de
MFC after: 3 days
functions that manage PV entries. Specifically, remove the PV entry from
the containing PV list only after the corresponding PTE is destroyed.
Update the pmap's wired mapping count in pmap_enter() before the PV list
lock is acquired.
- Add a couple of new devices
- Flow control changes in shared and core code
- Bug fix to Flow Director for 82598
- Shared code sync to internal with required core change
Thanks to those helping in the testing and improvements to this driver!
MFC after:5 days
shared code update and small changes in core required
Add support for new i210/i211 devices
Improve queue calculation based on mac type
MFC after:5 days
to build FreeBSD (they are used in Perl man pages). We never needed embedded
"!" in targets that I can find.
We got this from OpenBSD and I cannot find any other make that supports
such things -- contrary to their commit message claim: "This behaviour
is also consistent with other versions of make.".
natively rather than hand-assembled versions. For xgetbv/xsetbv, add a
wrapper API to deal with xcr* registers: rxcr() and load_xcr().
Reviewed by: kib
MFC after: 1 month
