and progif is evil. It doesn't work reliably[1] and we should honor BIOS
configuration by the user.
- If the SATA controller is enbled but combined mode is disabled, mask off
the emulated IDE channel on the legacy IDE controller.
Pointed out by: mav[1]
interface is fairly simple WRT dealing with flow control, but
needed 2 new RX buffer functions with "get-char-from-buf" separated
from "advance-buf-pointer" so that the pointer could be advanced
only when ttydisc_rint() succeeded.
MFC after: 1 week
The EHCI HW can use the qtd_next field instead of qtd_altnext when a short
packet is received. This contradicts what is stated in the EHCI datasheet.
Also the total-bytes field in the status field of the following TD gets
corrupted upon reception of a short packet! We work this around in software by
not queueing more than one job/TD at a time of up to 16Kbytes! The bug has been
seen on multiple INTEL based EHCI chips. Other vendors have not been tested
yet.
- Applications using /dev/usb/X.Y.Z, where Z is non-zero are affected, but not
applications using LibUSB v0.1, v1.2 and v2.0.
- Mass Storage (umass) is affected.
Submitted by: Hans Petter Selasky
MFC after: 3 days
Also, the previous commit to sys/dev/if_ndis/if_ndis.c also included the
removal of a call to ndis_setstate_80211 that is no longer needed.
Submitted by: sam
MFC after: 3 days
sysctl lock. The 'video' lock now protects the 'bus' of video output
devices attached to a graphics adapter. It is used when iterating over
the list of outputs, etc. The 'video_output' lock is used to lock the
output-specific data similar to a driver lock for the individual video
outputs.
MFC after: 2 weeks
1) Restore the PCI Express control register after a watchdog
reset. This is required because the device will come out
of watchdog reset with the pectl reg at its default state,
and important BIOS configuration (like max payload size)
could be lost.
2) Call mxge_start_locked() for every tx queue before dropping
the lock in the watchdog handler. This is required, as
the queue's buf ring may have filled during the reset.
perform 802.11 operations directly on the ndis0 interface before the
first VAP (wlan0) had been created. This would lead to a NULL-pointer
dereference in the kernel.
Submitted by: Paul B. Mahol <onemda@gmail.com>
MFC after: 3 days
capability to mii(4). Even though AR8132 uses the same model/
revision number of F1 gigabit PHY, the PHY has no ability to
establish 1000baseT link. I have no idea why Atheros use the same
device/model id for this PHY.
With this change atphy(4) does not report 1000baseT media
capability and manual 1000baseT configuration is also disabled
which is more desirable behavior for 10/100Mbps PHY.
Unlike most other PHYs there is no easy way to know which media
type the PHY supports on Marvell PHYs. MIIF_HAVEFIBER flags is now
passed via bus-specific instance variable of a device. While I'm
here add 88E1112 specific work around to set SIGDET polarity low.
Many thanks "Eugene Perevyazko <john <> dnepro dot net>" who kindly
gave remote access to system with DGE-560SX.
offloading. Datasheet said nothing about the limitation of 82559ER
except WOL. Explicitly disable Rx checksum offloading for
controllers that is known to lack the capability.
PR: kern/138135
Tested by: Gooderum, Mark < mgooderum <> websense dot com >
- Add quirk for ATI SB600 and SB700 to free SMB controller
- Correct schedule sleep time to 10us on the VIA ehci controller
Reported by: Dorian B<FC>ttner, Andriy Gapon
Submitted by: Hans Petter Selasky
- clean up USB detach logic. There seems to be some problems detaching multiple
USB HUBs connected in series from the root.
- after this patch the rule is:
1) Always use device_detach() on the USB HUB first.
2) Never just device_delete_child() on the USB HUB, because that function
will traverse to all the device leaves and free them first, and then the USB
stack will free the devices twice which doesn't work very well.
- make sure the did DMA delay gets set after the timeout has elapsed to make
logic more clear. There is no functional difference.
Submitted by: Hans Petter Selasky
Right now if applications want to use the mouse on the command line,
they use sysmouse(4) and install a signal handler in the kernel to
deliver signals when mouse events arrive. This conflicts with my plan to
change to TERM=xterm, so implement proper VT200-style mouse input.
Because mouse input is now streamed through the TTY, it means you can
now SSH to another system on the console and use the mouse there as
well. The disadvantage of the VT200 mouse protocol, is that it doesn't
seem to generate events when moving the cursor. Only when pressing and
releasing mouse buttons.
There are different protocols as well, but this one seems to be most
commonly supported.
Reported by: Paul B. Mahol <onemda gmail com>
Tested with: vim(1)
It is quite inconvenient that if an application for xterm uses 256 color
mode, text suddenly starts to blink (because of ;5; in the middle).
We'd better just implement 256 color mode and add a conversion routine
from 256 to 8 color mode, which doesn't seem to be too bad in practice.
Remapping colors is done quite simple. If one of the channels is most
actively represented, primary colors are used. If two channels are most
actively represented, secondary colors are used. If all three channels
are equal (gray), it picks between black and white.
Reported by: Paul B. Mahol <onemda gmail com>
devices that we also support, just not by default (thus only LINT or
module builds by default).
While currently there is only "/dev/full" [2], we are planning to see more
in the future. We may decide to change the module/dependency logic in the
future should the list grow too long.
This is not part of linux.ko as also non-linux binaries like kFreeBSD
userland or ports can make use of this as well.
Suggested by: rwatson [1] (name)
Submitted by: ed [2]
Discussed with: markm, ed, rwatson, kib (weeks ago)
Reviewed by: rwatson, brueffer (prev. version)
PR: kern/68961
MFC after: 6 weeks
- Clear all registers before calling real mode interrupt handlers as we did
for dpms and vesa and re-enable the function as it should be fixed by this.
- Tidy up register access. For example, when we call INT 0x15, AH=0xc0,
we used to initialize AX=0xc000 to clear AL at the same time but it is
very confusing. We don't have to do this any more because we are explicitly
clearing all registers now.
- Check size of system configuration table although it is almost always 8.
This is to make sure we are not reading some random low physical memory.
Hopefully it is just zero in that case. :-)
- Fix some style nits and add more comments.
Submitted by: paradox (ddkprog yahoo com)[1]
memory to support them. Some adapters have expansible memory slots but
video mode table is static. In this case, unusable modes may be reported.
Submitted by: paradox (ddkprog yahoo com) (initial patch)
Also align setup descriptor on 32 bytes boundary. Tx buffer have no
alignment limitation so create dmamap without alignment
restriction[1]. Rx buffer still seems to require 4 bytes alignment
limitation but we can simply use MCLBYTES for size to map the
buffer instead of TULIP_DATA_PER_DESC as the buffer is allocated
with m_getcl(9).
de(4) supports up to TULIP_MAX_TXSEG segments for Tx buffers,
increase maximum dma segment size to TULIP_MAX_TXSEG * MCLBYTES.
While I'm here remove TULIP_DATA_PER_DESC as it is not used anymore.
This should fix de(4) breakage introduced after r176206.
Submitted by: jhb [1]
Reported by: WATANABE Kazuhiro < CQG00620 <> nifty dot ne dot jp >
Tested by: WATANABE Kazuhiro < CQG00620 <> nifty dot ne dot jp >,
Takahashi Yoshihiro < nyan <> jp dot freebsd dot org >
o introduce PCIE_REGMAX and use it instead of ad-hoc constant
o where 'reg' parameter/variable is not already unsigned, cast it to
unsigned before comparison with maximum value to cut off negative
values
o use PCI_SLOTMAX in several places where 31 or 32 were explicitly used
o drop redundant check of 'bytes' in i386 pciereg_cfgread() - valid
values are already checked in the subsequent switch
Reviewed by: jhb
MFC after: 1 week
save/clear/restore flags but emulated flags have no effect on the host.
I believe BIOS writers never meant to run their code in emulated
environment with interrupt enabled. :-)
- Use memcpy(3) instead of copying individual members. I believe struct
x86regs was intentionally copied from the first half of struct x86emu_regs
for this very purpose.
- Fix some style nits and consistencies.
Reviewed by: delphij, paradox (ddkprog yahoo com)
startup and genericize it so it can be reused to map other tables as well:
- Add a routine to walk a list of ACPI subtables such as those used in the
APIC and SRAT tables in the MI acpi(4) driver.
- Move the routines for mapping and unmapping an ACPI table as well as
mapping the RSDT or XSDT and searching for a table with a given signature
out into acpica_machdep.c for both amd64 and i386.
than references to objects. In that case, simply use the Package directly.
I think a recent change to ACPI-CA is causing the interpreter to
automatically expand these references.
Reported by: Olivier Smedts olivier gid0 org
MFC after: 3 days
decoding "took". Other OS's that I checked do not do this and it breaks
some amdpm(4) devices. Prior to 7.2 we did not honor the error returned
when this failed anyway, so this in effect restores previous behavior.
PR: kern/137668
Tested by: Aurelien Mere aurelien.mere amc-os.com
MFC after: 3 days
the work area was totally unsynchronized which means this driver only
had a chance of working on x86 when no bounce buffers were involved,
which isn't that likely given that support for 64-bit DMA is currently
broken throughout ata(4).
- Add necessary little-endian conversion of accesses to the work area,
making this driver work on big-endian hosts. While at it, use the
alignment-agnostic byte order encoders in order to be on the safe side.
- Clear the reserved member of the SG list entries in order to be on the
safe side. [1]
Submitted by: yongari [1]
Reviewed by: yongari
MFC after: 3 days
30-bit like the reset of the controllers supported by this driver.
Actually ALi M5451 can be setup up to generate 32-bit addresses by
setting the 31st bit via the accompanying ISA bridge, which allows
it to work in sparc64 machines whose IOMMU require at least 32-bit
DMA. Even though other architectures would also benefit from 32-bit
DMA, enabling this bit is limited to sparc64 as bus_dma(9) doesn't
generally guarantee that a low address of BUS_SPACE_MAXADDR_32BIT
results in a buffer in the 32-bit range.
- According to Tatsuo YOKOGAWA's ali(4), the the DMA transfer size of
ALi M5451 is fixed to 64k and in fact using the default size of 4k
- The 4DWAVE DX and NX require the recording buffer to be 8-byte
aligned so adjust the bus_dma_tag_create(9) accordingly.
- Unlike the rest of the controllers supported by this driver, the
ALi M5451 only has 32 hardware channels instead of 64 so limit the
loop in tr_intr() accordingly. [1]
Submitted by: yongari [1]
Reviewed by: yongari (superset of what is committed)
MFC after: 3 days
It seems Clang breaks when checking for SPCLKEY, which is now
0x80000000. Using an unsigned integer fixes this. This is also
consistent with other pieces of kbd/syscons code, because these also use
u_int.
Submitted by: rdivacky
- Mark the link as down, so if watchdog reset fails, link watching
failover software can notice it
- Don't send MXGEFW_CMD_ETHERNET_DOWN if the NIC has been reset, it is
not needed, and will fail on a freshly reset NIC.
- Ensure the transmit routines aren't attempting to PIO write to doorbells
while the NIC is being reset.
- Download the correct f/w, rather than using the EEPROM f/w after reset.
- Export a count of the number of watchdog resets via sysctl
- Zero all f/w stats at reset. This will lead to less confusing
diagnostic output when investigating NIC failures.
MFC after: 3 days
instead of SI_SUB_KLD. Note that we don't believe that there is any
consumers of x86bios that would be triggered in the early stage of boot,
so this is more or less just a safebelt.
Submitted by: swell.k at gmail.com
x86emu to this new module.
This changeset also brings a fix for bugs introduced with the initial
x86emu commit, which prevents the user from using some display mode or
cause instant reboots during mode switch.
Submitted by: paradox <ddkprog yahoo com>
Add a maximum response length for FCP RSPNS IUs.
Clarify some of the FC option words for setting parameters
and try and disable automatic PRLI when in target mode- this
should correct some cases of N-port topologies with 23XX cards
where we put out an illegal PRLI (in target mode only we're
not supposed to put out a PRLI).
Just take keyent_t to use an u_int to store the Unicode codepoints.
Unfortunately the keymap is now too big to be loaded using an ioctl
argument, so change the ioctl to pick a pointer.
This change breaks kbdcontrol ABI. It doesn't break X11, because X11
doesn't do anything with syscons keymaps. It just switches the device
out of K_XLATE.
Obtained from: //depot/user/ed/newcons/...
This code seems to do exactly the same as ttydisc_rint_simple() does
nowadays. Just remove it.
Obtained from: //depot/user/ed/newcons/sys/dev/syscons/syscons.c
- Implement MSI support (MSIX support was already there)
- Use a table to drive MSI/MSIX exceptions
- Pre-calculate the command address instead of wasting cycles doing the
calculation on every i/o.
number of MSIX interrupts that are needed, and don't strictly check for 4.
Enable enough interrupt mask bits so that the controller will generate
interrupts in PERFORMANT mode. This fixes the hang-on-boot issues that
people were seeing with newer controllers.
we at least don't panic.
We don't really support dual role mode (INITIATOR/TARGET) any more. We
should but it's broken and will take a fair amount of effort to fix
and correctly manage both initiator and target roles sharing the port
database. So, for now, disallow it.