While it is the recommended initialization procedure, it hangs on the reset
of the second GPIO module on pandaboard.
Removes the module reset for now as more investigation would be needed.
Reported by: jceel
On AM335x each one of the four GPIO banks has two physical interrupt
lines, so we now allocate resources and setup our interrupt handler for
all the (8) available interrupts.
On OMAP3 and OMAP4 there is only one interrupt for each GPIO bank (6
banks, 6 interrupts), but there are two set of registers where the
first one is used to setup the delivery of interrupts to the MPU and
the second set, setup the delivery of interrupts to the DSP.
On AM335x, each set of registers controls each one of the interrupt
lines.
- Remove nonexistent registers for OMAP4 and AM335x, replace their use with
the correct ones for these SoCs.
- Remove stray whitespace.
Based on OMAP3, OMAP4 and AM335x TRMs.
Tested on Beaglebone-black.
- Don't allow high-speed mode on OMAP4 due to hardware erratum.
- Check the proper bit in the status register when waiting for the
controller to come out of reset.
- Add handling for the "non-removable" fdt property by always returning
"card is present" status.
- Add the non-removable property for the MMC card on a Beaglebone Black.
- Add the non-removable property for Pandaboard as a workaround.
For Pandaboard the card detect pin is handled by the twl6030 fpga device
which gets an interrupt on pin change and then has to query the fpga
for the actual status. We don't have code to do that yet.
Submitted by: Svatopluk Kraus <onwahe@gmail.com>
errors.
Reset the GPIO module during the initialization. This is guaranteed to be
the same as a hardware reset. Tested on AM335x (BBB) and checked against
the omap3 and omap4 TRM.
Do a better job freeing resources when there are errors and on
ti_gpio_detach().
description was eaten by the dog (or an editor crash or something).
Add variable-frequency support to the arm mpcore eventtimer driver.
This allows a platform's early init code to tell the mpcore driver that the
clock frequency can vary. That causes the mpcore driver to register an
eventtimer, but not a timecounter. The platform has to provide a time
counter using some other fixed-frequency clock, but can still use the
per-cpu goodness of the mpcore hardware for event timers.
When the platform support code does something to change the frequency of
the CPU clocks (power saving, thermal management) it must tell the mpcore
driver code about it using arm_tmr_change_frequency().
The ADC has a 12bit resolution and its raw output can be read via sysctl(8)
interface.
The driver allows the setup of ADC clock, samples average and open delay
(the number of clock cycles to wait before start the conversion).
The TSC_ADC module is set in the general purpose mode (no touchscreen
support).
Tested on Beaglebone-black.
Written based on AM335x TRM.
Reviewed by: rpaulo
Approved by: adrian (mentor)
Tested by: me, Brian J. McGovern, Sulev-Madis Silber (ketas)
and the functionality it provided into arm/exception.S. Rename the main
irq handling routine from arm_handler_execute() to arm_irq_handler() to
make it more congruent with how other exception handlers are named, and
also update its signature to reflect what has long been reality: it is
passed just a trapframe pointer, no interrupt number argument.
appropriate for each of the 'foo' in the tree. This will allow us to
compile them together (although symbol conflicts prevent us from doing
that today, this just fixes the file name collision).
implementation in arm/machdep.c. Most arm platforms either don't need to
do anything, or just need to call the standard eventtimer init routines.
A generic implementation that does that is now provided via weak linkage.
Any platform that needs to do something different can provide a its own
implementation to override the generic one.
it into a bunch of different .c files. Remove declarations for the unused
mptramp() function from everywhere except AramadaXP (and I think it's
really not used there either, because the code that references it appears
to be insanely does-nothing in nature).
change the gpio children can be described as directly connected to the GPIO
controller without the need of describing the OFW GPIO bus itself on the
DTS file.
With this commit the OFW GPIO bus is fully functional on BBB and RPi.
GPIO controllers which want to use the OFW GPIO bus will need similar
changes.
Approved by: adrian (mentor, implicit)
to check the status property in their probe routines.
Simplebus used to only instantiate its children whose status="okay"
but that was improper behavior, fixed in r261352. Now that it doesn't
check anymore and probes all its children; the children all have to
do the check because really only the children know how to properly
interpret their status property strings.
Right now all existing drivers only understand "okay" versus something-
that's-not-okay, so they all use the new ofw_bus_status_okay() helper.
Note that this commit hasn't been compile tested because these files
are not hooked up to the build...
PR: 186129
Submitted by: Takanori Sawada
Approved by: rpaulo
and add static mappings that cover most of the on-chip peripherals with
1MB section mappings. This adds about 220MB or so available kva space
by not using a hard-coded 0xF0000000 as the mapping address.
searching. If you didn't configure a timer capture pin you'd get a data
abort as it wandered into the weeds, now you get a nice warning message
about your config, as originally intended.
capture mode together with the timecounter's PPS polling feature to get
very accurate PPS capture without any interrupt processing (or latency).
Hardware timers 4 through 7 have associated capture-trigger input pins.
When the PPS support is compiled in the code automatically chooses the
first timer it finds that has the capture-trigger pin set to input mode
(this is configured via the fdt data).
- Use named constants for register bits, instead of mystery numebrs
scattered around in the code.
- Use inline functions for bus space read/write, instead of macros
that rely on global variables.
- Move the timecounter struct into the softc instead of treating it
as a global variable. Backlink from it to the softc.
- This leaves a pointer to the softc as the only static/global variable
and it's now used only by DELAY().
this change we may end up with a panic (Fatal kernel mode data abort:
'External Non-Linefetch Abort (S)') as described in
http://e2e.ti.com/support/arm/sitara_arm/f/791/t/276862.aspx.
It is now possible to bring up I2C1 and I2C2 on BBB.
Approved by: adrian (mentor)
always returning '0' for all the reads, even for the outputs. It is now
known to work with gpioiic(4) and gpioled(4).
Approved by: adrian (mentor)
Tested on: BBB
host.host_ocr, examine the correct field when setting up the hardware. Also,
the offset for the capabilties register should be 0x140, not 0x240.
Submitted by: Ilya Bakulin <ilya@bakulin.de>
Pointy hat to: me
static device mappings, rather than as the first of the initializations
that a platform can hook into. This allows a platform to allocate KVA
from the top of the address space downwards for things like static device
mapping, and return the final "last usable address" result after that and
other early init work is done.
Because some platforms were doing work in initarm_lastaddr() that needs to
be done early, add a new initarm_early_init() routine and move the early
init code to that routine on those platforms.
Rename platform_devmap_init() to initarm_devmap_init() to match all the
other init routines called from initarm() that are designed to be
implemented by platform code.
Add a comment block that explains when these routines are called and the
type of work expected to be done in each of them.
new devmap.[ch] files. Emphasize the MD nature of these things by using
the prefix arm_devmap_ on the function and type names (already a few of
these things found their way into MI code, hopefully it will be harder to
do by accident in the future).
Use the published compatible strings (our own invention, "ti,mmchs" is
still accepted as well, for now).
Don't blindly turn on 8-bit bus mode, because even though the conroller
supports it, the board has to be wired appropriately as well. Use the
published property (bus-width=<n>) and honor all the valid values (1,4,8).
The eMMC device on a Beaglebone Black is wired for 8-bit, update the dts.
The mmchs controller can inherently do both 1.8v and 3.0v on the first
device and 1.8v only on other devices, unless an external transceiver is
used. Set the voltage automatically for the first device and honor
the published fdt property (ti,dualvolt) for other devices.
Thanks go to Ilya Bakulin for figuring out the voltage compatibility stuff.
The only remaining user was the code that allocates bounce pages for armv4
busdma. It's not clear why bounce pages would need uncached memory, but
if that ever changes, kmem_alloc_attr() would be the way to get it.
really need it. That would be almost everywhere it was included. Add
it in a couple files that really do need it and were previously getting
it by accident via another header.
included by vm/pmap.h, which is a prerequisite for arm/machine/pmap.h
so there's no reason to ever include it directly.
Thanks to alc@ for pointing this out.
