IF_ADDR_UNLOCK() across network device drivers when accessing the
per-interface multicast address list, if_multiaddrs. This will
allow us to change the locking strategy without affecting our driver
programming interface or binary interface.
For two wireless drivers, remove unnecessary locking, since they
don't actually access the multicast address list.
Approved by: re (kib)
MFC after: 6 weeks
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
o add IEEE80211_C_STA capability to indicate sta mode is supported
(was previously assumed) and mark drivers as capable
o add ieee80211_opcap array to map an opmode to the equivalent capability bit
o move IEEE80211_C_OPMODE definition to where capabilities are defined so it's
clear it should be kept in sync (on future additions)
o check device capabilities in clone create before trying to create a vap;
this makes driver checks unneeded
o make error codes return on failed clone request unique
o temporarily add console printfs on clone request failures to aid in
debugging; these will move under DIAGNOSTIC or similar before release
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)