from
all AAAA trial, then all A trial
to
try AAAA and A for each trial
TODO: more fix for the case where IPv4 mapped IPv6 addr is disabled
Reviewed by: ume
maintainers.
After we established our branding method of writing upto 8 characters of
the OS name into the ELF header in the padding; the Binutils maintainers
and/or SCO (as USL) decided that instead the ELF header should grow two new
fields -- EI_OSABI and EI_ABIVERSION. Each of these are an 8-bit unsigned
integer. SCO has assigned official values for the EI_OSABI field. In
addition to this, the Binutils maintainers and NetBSD decided that a better
ELF branding method was to include ABI information in a ".note" ELF
section.
With this set of changes, we will now create ELF binaries branded using
both "official" methods. Due to the complexity of adding a section to a
binary, binaries branded with ``brandelf'' will only brand using the
EI_OSABI method. Also due to the complexity of pulling a section out of an
ELF file vs. poking around in the ELF header, our image activator only
looks at the EI_OSABI header field.
Note that a new kernel can still properly load old binaries except for
Linux static binaries branded in our old method.
*
* For a short period of time, ``ld'' will also brand ELF binaries
* using our old method. This is so people can still use kernel.old
* with a new world. This support will be removed before 5.0-RELEASE,
* and may not last anywhere upto the actual release. My expiration
* time for this is about 6mo.
*
connections, after SYN packets were seen from both ends. Before this,
it would get applied right after the first SYN packet was seen (either
from client or server). With broken TCP connection attempts, when the
remote end does not respond with SYNACK nor with RST, this resulted in
having a useless (ie, no actual TCP connection associated with it) TCP
link with 86400 seconds TTL, wasting system memory. With high rate of
such broken connection attempts (for example, remote end simply blocks
these connection attempts with ipfw(8) without sending RST back), this
could result in a denial-of-service.
PR: bin/17963
but with `dst_port' work for outgoing packets.
This case was not handled properly when I first fixed this
in revision 1.17.
This change is also required for the upcoming improved PPTP
support patches -- that is how I found the problem.
Before this change:
# natd -v -a aliasIP \
-redirect_port tcp localIP:localPORT publicIP:publicPORT 0:remotePORT
Out [TCP] [TCP] localIP:localPORT -> remoteIP:remotePORT aliased to
[TCP] aliasIP:localPORT -> remoteIP:remotePORT
After this change:
# natd -v -a aliasIP \
-redirect_port tcp localIP:localPORT publicIP:publicPORT 0:remotePORT
Out [TCP] [TCP] localIP:localPORT -> remoteIP:remotePORT aliased to
[TCP] publicIP:publicPORT -> remoteIP:remotePORT
INADDR_NONE: Incoming packets go to the alias address (the default)
INADDR_ANY: Incoming packets are not NAT'd (direct access to the
internal network from outside)
anything else: Incoming packets go to the specified address
Change a few inaddr::s_addr == 0 to inaddr::s_addr == INADDR_ANY
while I'm there.
redirected and when no target address has been specified, NAT
the destination address to the alias address rather than
allowing people direct access to your internal network from
outside.
some reason. This will prevent an infinite loop if (say) a sigalarm is
being scheduled at a more frequent interval than the poll timeout.
PR: 2191, 8847, 10553
