per-cpu variants are also available to be called. The per-cpu variants
are needed for some later optimizations.
Also remove unnecessary casts, do some style fixes.
Reviewed by: alc, neel
bufobj lock. If b_bufobj is not NULL, then bufobj lock should be
held when manipulating the flags. Not doing this sometimes leaves
BV_BKGRDINPROG to be erronously set, causing softdep' getdirtybuf() to
stuck indefinitely in "getbuf" sleep, waiting for background write to
finish which is not actually performed.
Add BO_LOCK() in the cases where it was missed.
In collaboration with: pho
Tested by: bz
Reviewed by: jeff
MFC after: 1 month
the worklist (in softdep_process_journal), but also after flushing the
workitems. Might be, we should even do this before bwillwrite() too, but
this seems to be not needed for now.
Fs might be suspended during processing the queue, and then there is
nobody around to unsuspend.
In collaboration with: pho
Tested by: bz
Reviewed by: jeff
If it does, don't then try reprogramming the NF "cap" values (ie
what values are the "maximum" value the NF can be) - instead,
just leave the current CCA value as the NF cap.
This was inspired by some similar work from ath9k. It isn't
a 100% complete solution (as there may be some reason where a
high NF CCA/cap is written, causing the baseband to stop thinking it
is able to transmit, leading to stuck beacon and interface reset)
which I'll investigate and look at fixing in a later commit.
Obtained from: Linux
AR5416 and later chipsets.
ath_hal_calibrateN() calls the HAL calibrateN function with rxchainmask=0x1.
This is not necessarily the case for AR5416 and later chipsets.
use-after-free over a longer time. Also release the backing pages of
a guarded allocation at free(9) time to reduce the overhead of using
memguard(9). Allow setting and varying the malloc type at run-time.
Add knobs to allow:
- randomly guarding memory
- adding un-backed KVA guard pages to detect underflow and overflow
- a lower limit on the size of allocations that are guarded
Reviewed by: alc
Reviewed by: brueffer, Ulrich Spörlein <uqs spoerlein net> (man page)
Silence from: -arch
Approved by: zml (mentor)
MFC after: 1 month
are served via an interrupt gate.
However, that doesn't explicitly prevent preemption and thread
migration thus scheduler pinning may be necessary in some handlers.
Fix that.
Tested by: gianni
MFC after: 1 month
r211130 in favor of this more general fix.
This fixes a compilation error for mips 64-bit little endian build.
libexec/rtld-elf/mips/reloc.c:196: warning: right shift count >= width of type
Suggested by: stefanf, jchandra, bde
bridge(4), lagg(4) etc. and make use of function pointers and
pf_proto_register() to hook carp into the network stack.
Currently, because of the uncertainty about whether the unload path is free
of race condition panics, unloads are disallowed by default. Compiling with
CARPMOD_CAN_UNLOAD in CFLAGS removes this anti foot shooting measure.
This commit requires IP6PROTOSPACER, introduced in r211115.
Reviewed by: bz, simon
Approved by: ken (mentor)
MFC after: 2 weeks
list of devices supported by uplcom(4) with the following sources:
NetBSD src/sys/dev/usb/uplcom.c 1.70
OpenBSD src/sys/dev/usb/uplcom.c 1.52
Linux drivers/usb/serial/pl2303.h from kernel 2.6.35
BeOS usb_serial/driver.c 1.32
Give several devices better descriptions, and rename
PROLIFIC2 -> NETINDEX while here to match everybody else.
MFC after: 6 weeks (after r211111)
While there, also fix some places assuming cpu type is 'int' while
u_int is really meant.
Note: this will also fix some possible races in per-cpu data accessings
to be addressed in further commits.
In collabouration with: Yahoo! Incorporated (via sbruno and peter)
Tested by: gianni
MFC after: 1 month
flag immediately so it's only set once per longcal interval.
Without this, the current AR5416 code will continuously spam NF
calibrations during a periodic calibration if the longcal flag
is set. The longcal flag wouldn't be cleared until the calibration
method indicates that calibrations are "complete".
This drops the rate of NF calibration updates down from "once every
shortcal" (ie, every 100ms) during a periodic calibration, to only
once per "longcal" interval. Spamming NF calibrations every 100ms
caused some potentially horrific issues in noisy environments as
NF calibrations can take longer than 100ms and this spamming can
cause invalid NF calibration results to be read back - leading to
missed beacons, and thus leading to a stuck beacon situation.
Stuck beacons cause interface resets, which restart calibrations.
This means that the longcal calibration runs every 100ms (shortcal)
until all initial calibrations are completed. This spamming can then
cause the above issues which leads to stuck beacons, leading to
interface resets, etc, etc. Quite annoying.
Now we use a regular mutex instead of a spin mutex. When we enter and exit
the emulator, spinlock_enter() and spinlock_exit() are additionally used.
Move some page table related stuff from x86bios_init() and x86bios_uninit()
to x86bios_map_mem() and x86bios_unmap_mem().
most system, based on benchmark results on a low-end fibre channel SAN
under VMWare:
vfs.read_max read performance
8 (historical default) 83 MB/s
16 (recent bump) 131 MB/s
32 (this version) 152 MB/s
64 157 MB/s
(results are +/- 3 MB/s)
As read-ahead is heuristic, based on past IO requests, it shouldn't be
problematic. The new default is still smaller then in other OSes.
Add proto spacers to inet6sw like we have for legacy IP. This allows us
to dynamically pf_proto_register() for INET6 from modules, needed by
upcoming CARP changes and SeND.
MC and SCTP could make use of it as well in theory in the future after
upcoming VIMAGE vnet teardown work.
Discussed with: will, anchie
MFC after: 10 days
Even though cons25 normally doesn't support origin regions, this
emulator does allow you to do it. It makes more sense to blank only the
origin region when emitting ^L instead of blanking the entire screen.
Apart from that, we should always place the cursor inside the origin
region, which doesn't happen right now.
within the device table. This code uses the same algorithm as used in the
Linux, NetBSD and DragonflyBSD driver.
While investigating this, it became apparent that the Linux driver always
initialises the device, and not just in the PL2303HX case. Change
uplcom(4) to do the same.
This change allows us to synchronize our device ID list with Linux and
NetBSD, without requiring knowledge of the chipset in use.
Reviewed by: hselasky
MFC after: 6 weeks
controller. These controllers are known as L1D(AR8151) and
L2CB/B2(AR8152). This change adds supports for the following
controllers.
o AR8151 v1.0(L1D) gigabit ethernet controller
o AR8151 v2.0(L1D) gigabit ethernet controller
o AR8152 v1.1(L2CB) fast ethernet controller
o AR8152 v2.0(L2CB2) fast ethernet controller
These controllers have the same feature of AR8131/AR8132 and
support improved power saving control. The user visible change at
this moment is reduced jumbo frame size from 9KB to 6KB. Many
thanks to Atheros for continuing to support FreeBSD.
HW donated by: Atheros Communications, Inc.
- Increase target limit from 4 to 64; this limit will be removed entirely
at a later time.
- Improve recovery from lost network connections.
- Fix some potential deadlocks and a serious memory leak.
- Fix incorrect use of MH_ALIGN (instead of M_ALIGN), which makes no
practical difference, but triggers a KASSERT with INVARIANTS.
- Fix some warnings in iscontrol(8) and improve the man page somewhat.
Submitted by: Daniel Braniss <danny@cs.huji.ac.il>
Sponsored by: Dansk Scanning A/S, Data Robotics Inc.
This fixes booting from a ZFS mirror with a unavailable primary device.
PR: kern/148655
Reviewed by: avg
Approved by: delphij (mentor)
MFC after: 3 days
like memory mapped register access. Typical problem from the issue
was MII access returned unreliable values. I'm not sure this comes
from lack of register flushing in MII access after accessing
STE_PHYCTL register though.
To address the issue, read hints data that controls which type of
memory mapping should be used in driver. ste(4) still prefers
memory mapping to io mapping but honor hints entered by user except
for controllers that have problems with memory mapping.
The hint to use iomapping could be given by adding the following
line to /boot/device.hints file.
hint.ste.0.prefer_iomap="1"
PR: kern/149285
MFC after: 5 days
number of CPUs detection.
However, that was not mention at all, the problem was not reported, the
patch has not been MFCed and the fix is mostly improper.
Fix the original overflow (caused when 32 CPUs must be detected) by
just using a different mathematical computation (it also makes more
explicit the size of operands involved, which is good in the moment
waiting for a more complete support for a large number of CPUs).
PR: kern/148698
Submitted by: Joe Landers <jlanders at vmware dot com>
Tested by: gianni
MFC after: 10 days
