registers.) Also clean up some namespace pollution, and remove
gcc-1 support (nothing really works with it anymore anyway.)
Submitted by: Bruce Evans <bde@freebsd.org> and me.
the queues and generate a SIGINT. Previously, this wasn't done if ISIG
was clear or the VINTR character was disabled, and it was done by
converting the BREAK to a VINTR character and sometimes bogusly echoing
this character.
Found by: NIST-PCTS
consistent stack frame in fastmove() so that only one new fault handler
is necessary.
Should be in 2.2. Harmless until the i586 versions are reenabled.
Per Wayne Scott of Intel, the old sequence took 20cycles!!! on a P6.
Another nice side-benefit is that the kernel is about 3K smaller!!!
Submitted by: Wayne Scott <wscott@ichips.intel.com>
larger than the vfs layer can provide. We now automatically support
32K clusters if MSDOSFS is installed, and panic if a filesystem tries
to allocate a buffer larger than MAXBSIZE.
This commit is a result of some "prodding" by BDE.
larger than the vfs layer can provide. We now automatically support
32K clusters if MSDOSFS is installed, and panic if a filesystem tries
to allocate a buffer larger than MAXBSIZE.
This commit is a result of some "prodding" by BDE.
The rest of the code was treating it as a header mbuf, but it was
allocated as a normal mbuf.
This fixes the panic: ip_output no HDR when you have a multicast
tunnel configured.
the keyboard IO port definitions from <machine/console.h>.
Note: I do not have a machine available to test this yet, I sent this
for review to several people who have not replied.
This is also totally busted in 2.2, which has half of the syscons/psm/kbdio
changes in it. This really desperately needs to be tested and fixed
in 2.2 as well.
SCBs in response to a busfree.
When re-queueing an SCB that returned with QUEUE FULL status, reset its timeout.
Ensure that aborted SCBs have an error code set in there xs before it gets
passed back up with scsi_done.
Fix a few KNF nits.
Immediate SCBs, since they always send messages that tell the target to
transition to bus free now rely on the busfree interrupt instead of the
IMMEDDONE sequencer interrupt that was generated before.
Rearrange some code in the message out loop to give ATN a little more time
to drop before we ACK the last byte.
Use SPIORDY instead of REQINIT when snooping for a tag message on a reconnect.
This is done for the same reasons we use SPIORDY in the inb functions.
When going into BITBUCKET mode, turn off HDMAEN in the DFCNTRL register so
that we can "not care" what the value of HCNT is. If HCNT is 0, BITBUCKET
mode won't transfer any data if HDMAEN is set. Seeing as we don't want the
transfer to even think about touching the host, this seems more sane anyway.
Thanks to "Dan Willis" <dan@plutotech.com> for pointing out that this was
a problem.
uses /usr/include/sys/*, which may point to a different build tree. I'm
not sure that this is necessary, but there was a question mark over what
/usr/include/sys points to when building the "user mode" binaries in the
kernel code, especially when building the smp tree.
I suspect that the "right" line here is to use ${INCLUDES}, but that
causes warnings about unused static inline functions in stdio.h and ctype.h
also fixes a bug I've been chasing for a LONG TIME,
due to the fact that spec_bwrite is a NOP and I didn't realise it..
old symptom:
mount -t devfs devfs /mnt
mount /mnt/wd0e /mnt/mnt2
umount /mnt2 <process hangs>
there are some pretty large structural differences internal to devfs
but outwards it should look the same.
I have not yet tested extensively but will do so and fix 3 warnings tomorrow.
SPIORDY should go active on any REQ of the bus, so testing for REQINIT is
not necessary. It also seems that testing for SPIORDY is more robust then
REQINIT since SPIORDY comes active after REQINIT and PHASEMIS seems to take
some time to come true after REQ is asserted if the phase has changed. Of
course, none of this is documented.
This should give the code savings of my original changes, without breaking the
driver on fast peripherals.
The 'getchar' function in syscons (sccngetc) is used by UserConfig to
get keyboard input from the user. When it was modified to use the
shared keyboard port routines it used the port passed in during the
probe routine. Since the probe routine was not yet called, the port was
set to 0, which is obviously not going to work.
Pre-initialize sc_port to IO_KBD which is really a kludge, but it's how
the previous driver did it's job.
Found by: remote GDB
substantially increasing buffer space. Specifically, we double
the number of buffers, but allocate only half the amount of memory
per buffer. Note that VDIR files aren't cached unless instantiated
in a buffer. This will significantly improve caching.
do reset it from the QOUTCNT register inside a pause/unpause. This now happens
once per command complete interrupt in the paging case (one interrupt can be
for multiple completed commands). I may introduce a counter and do a lazy
update in the future, similar to what is done with the QINCNT.
Enhance the QUEUE FULL condition handling so that the number of openings will
be reduced. This has become more important now that the driver is faster.
This code really belongs in the gerneric SCSI layer, as will be the case once
3.0 gets the code from the 'SCSI' branch.
Add some #if 0'd out trace code I've been using to help debug sequencer
problems.
Fix the SCB paging problem that I was seeing. This was only on my 7850
controller and stems from the fact that its QINFIFO can only handle 3bit
SCB identifiers. This means that you can only have 8 transactions open at
a time with the current paging scheme to these controllers. The code added
to enforce this is generic in that it tests for the number of relevent bits
that the QINFIFO can store and adjusts the max accordingly. It may be possible
to come up with a scheme that allows for more than 8 commands at a time, but
I don't know that it is worth the effort simply to fix a low end card. The
aic7880 still can do 255.
This problem may be related to what Andrey was seeing since I don't have n
aic7770 rev E chip here to test on, but as soon as someone probes one of these
cards with this new code, the dmesg output will tell the whole story.
aic7xxx cards failing on certain motherboards, reverse the logic used to
control this feature. AHC_FORCE_PIO is replaced with AHC_ALLOW_MEMIO.
GENERIC no longer needs to specify the AHC_FORCE_PIO option since this is
the default.
initial selection when entering the status phase. This is the same assertion
we use for all the other data transfer phases.
Hopefully fix the hangs in the mesgin and mesgout phases that I introduced
last week during some code cleanup. I need to get some of these 12MB/s
drives so I can reproduce these hangs here...
Add a pause disable in the SCB paging case around our manipulation of the
QOUTQCNT variable. This is simply extra sanity.
Set LASTPHASE to P_BUSFREE once we see a busfree so that the kernel driver can
differentiate this from a data out phase.
user supplies a bad address, because they push a lot of stuff that the
fault handler doesn't know about onto the stack. This has been broken
for more than half a year despite being tested for almost half a year
in -current.
duplicate ip address 204.162.228.7! sent from ethernet address: 08:00:20:09:7b:1d
changed to
arp: 08:00:20:09:7b:1d is using my IP address 204.162.228.7!
and
arp info overwritten for 204.162.228.2 by 08:00:20:09:7b:1d
changed to
arp: 204.162.228.2 moved from 08:00:20:07:b6:a0 to 08:00:20:09:7b:1d
I think the new wordings are more clear and could save some support
questions.
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
with the copyright stuff fixed so soon (this should be merged into 2.2 when
you have a chance, Poul).
This is the new AWE32 driver, with support for the AWE32's fancy MIDI
synthesizer. The utilities for this will appear as port submissions soon
afterwards, according to the submitter.
Submitted-By: Randall Hopper <rhh@ct.picker.com>
Written-By: Takashi Iwai <iwai@dragon.mm.t.u-tokyo.ac.jp>
the other two trees. Bump RELDATE to Feb 1997, one greater than 2.2.
Now I can go update my porting.sgml.
NOT a 2.2 candidate, in case phk's wondering. :)
routines. An older version of this was tested successfully on all of my
systems with PS/2 mice. This was brought in without testing because it
is necessary due to the previously committed syscons changes.
Submitted by: Kazutaka Yokota <yokota@zodiac.mech.utsunomiya-u.ac.jp>
syscons and psm, curtesy Kazutaka Yokota with minor changes by
me. This contains an update of the psm driver as well.
This also fixes the breakage that I introduced to the psm driver by
making syscons poll for keyboard events in the atempt to fix the
hanging keyboard problem.
It works perfectly for me, and I'd like to hear from all that
have had keyboard/ps/2 mouse problems if this is the cure...
Submitted by: Kazutaka YOKOTA (yokota@zodiac.mech.utsunomiya-u.ac.jp)
wdreg.h: Delete wd_ctlr macro. PC98 version of wd.c treats it as a
variable.
GENERIC98: Delete ep0 entry. Current ep driver write I/O port 0x100.
This clobbers ICW of i8259, because upper 8bits of address line is not
masked on mother board.
if_fe.c: Merge from revision 1.18 of sys/i386/isa/if_fe.c.
pc98.c: Globalize dmapageport, because SCSI driver use this
variable.
wd82371.c: Yet another merge.
These are 2.2 candidates.
Submitted by: The FreeBSD(98) Development Team
almost complete control over RTS (control of its initial value is still
missing).
This fixes PR 1644 for sio.
The author of PR 1644 wants it in 2.1.6 and 2.2. This may be safe since
the complications are only in rarely used cases that I hope I've covered.
sys/pc98/i386/machdep.c: sync with i386/i386/machdep.c
sys/pc98/conf/options.pc98: sync with i386/conf/options.i386
sys/i386/isa/sound: DMA auto initialize mode support for PC98.
contributed by: Akio Morita <amorita@bird.scphys.kyoto-u.ac.jp>
Definite 2.2 material, I believe.
Submitted by: The FreeBSD (98) Development Team
We encountered an interesting situation where the superblock for
a file system got written to disk with the "fs_fmod" flag set to
one. It appears that this flag is normally supposed to be cleared
during ffs_sync(), but we experienced a crash, or some other weird
occurrence that left it on the disk set to 1.
Later this partition was mounted read-only... and the fs_fmod
field was never cleared, causing ffs_sync() to panic "rofs mod"
when trying to unmount that filesystem (ffs_vfsops.c: line 790).
fix:
set this bit to 0 when you load the superblock from disk.
(see more complete mail on this to hackers)
bridges with support for 64 bit memory addresses and 32 bit I/O addresses).
The code is not complete. It ignores the upper half of the long addresses.
This is not a problem on PC compatible systems, but has to be fixed for
real computers.
one too small for (hex) 12345678 and 4 too small for -1234567890. Large
values can be created by config and userconfig although not (previously)
by visual userconfig.
Fixed a sign extension bug for backspacing on "negative" hex values in
editval().
Increased field width and range for `flags' so that all possible values
can be displayed and edited.
actually harmless.
2. Fixed code to match comment in scintr().
3. Don't allow even root to take control of the machine when securelevel > 0.
I've secured the accesses to PSL_IOPL in all drivers and asked pst to
review it, but he seems to be busy. Write access to /dev/kmem and
other critival devices currently leaks across raisings of securelevel
via open fd's, so there may as well be a similar leak for PSL_IOPL.
4. (Most important.) Don't corrupt memory beyond the screen buffers if
the cursor happens to be off the 80x25 screen when syscons starts.
5. Fix console cursor update (not perfect yet).
Submitted by: bruce
~
getting the same behavior using the flags, which can be done inside of
UserConfig. (Also document other syscons flags which were previously
undocumented).
Requested by: bde
negative-logic flags (flags 0x01 and 0x02 for npx0, defaulting to unset = on).
This changes the default from off to on. The options have been in current
for several months with no problems reported.
Added a boot-time negative-logic flag for the old I5886_FAST_BCOPY option
which went away too soon (flag 0x04 for npx0, defaulting to unset = on).
Added a boot-time way to set the memory size (iosiz in config, iosize in
userconfig for npx0).
LINT:
Removed old options. Documented npx0's flags and iosiz.
options.i386:
Removed old options.
identcpu.c:
Don't set the function pointers here. Setting them has to be delayed
until after userconfig has had a chance to disable them and until after
a good npx0 has been detected.
machdep.c:
Use npx0's iosize instead of MAXMEM if it is nonzero.
support.s:
Added vectors and glue code for copyin() and copyout().
Fixed ifdefs for i586_bzero().
Added ifdefs for i586_bcopy().
npx.c:
Set the function pointers here.
Clear hw_float when an npx exists but is too broken to use.
Restored style from a year or three ago in npxattach().
2.2 are more obvious. -Winline is unimportant, but -W gives thousands
of warnings for comparisions. Turning off -W also loses warnings for:
- auto variables clobbered by longjmp. Not much of a problem in the kernel.
- functions returning without a value. I don't like losing this.
- an expression statement or the left side of a comma operand contains no
side effects. Turning this off also stops warnings for the low quality
debugging macros in gsc.c and lpt.c.
Should be in 2.2.
for get_diskinfo(), whose BIOS call sets %es:%edi in some cases, although
most documentation says that it doesn't change %edi in the cases that
happened to matter (for hard disks).
This shall be in 2.1.6 and 2.2.
Submitted by: Tor.Egge@idt.ntnu.no
(except I kept the unnecessary preservation of %edx and %ecx)
are adding new drivers...) to match, as best I can tell, majors.i386.
Improve behaviour when attempting to save changes for devices that should
not be changeable. Now correclty avoids non-device items, PCI devices and
devices with no isa_device structure.
Submitted by: (observations from) joerg, bde
uses one or the other. This required some changes to the ahc_reset()
function, and how early the probes had to allocate their softc.
Turn the AHC_IN/OUT* macros into inline functions and lowercase their names
to indicate this change. Geting AHC_OUTSB to work as a macro doing
conditional memory mapped I/O would have been too gross.
Be smart about the STPWEN control bit in SCFRCTL1. It should only be set
if the low byte of the bus is to be terminated. We figure this out either
by "caching" the value left over from the BIOS setup before we reset the card
or by using the values stored in the seeprom if it is availible.
uses one or the other. This required some changes to the ahc_reset()
function, and how early the probes had to allocate their softc.
Turn the AHC_IN/OUT* macros into inline functions and lowercase their names
to indicate this change. Geting AHC_OUTSB to work as a macro doing
conditional memory mapped I/O would have been too gross.
Stop setting STPWEN in the main driver and let the PCI front end do it
instead. It knows better.
Add the clearing of the QOUTQCNT variable during command complete processing
in the SCB paging case.
Go back to doing unconditional retries for the QUEUE FULL status condition.
This is really a kludge, but the code to handle it properly is on the SCSI
branch and will not make it into 2.2.
uses one or the other. This required some changes to the ahc_reset()
function, and how early the probes had to allocate their softc.
Turn the AHC_IN/OUT* macros into inline functions and lowercase their names
to indicate this change. Geting AHC_OUTSB to work as a macro doing
conditional memory mapped I/O would have been too gross.
1) get_free_or_disc_scb was not being passed its argument correctly
in one case
2) Add protection in the form of the QOUTQCNT variable to prevent
overflowing the QOUTFIFO.
This should make SCB Paging work. Really, I mean it now. 8-)
using a sockaddr_dl.
Fix the other packet-information socket options (SO_TIMESTAMP, IP_RECVDSTADDR)
to work for multicast UDP and raw sockets as well. (They previously only
worked for unicast UDP).
This allows the user to add modify syscons's configuration flags using
UserConfig that will allow older/quirky hardware (most notably older IBM
ThinkPad laptops) to work with the standard boot kernel.
Inspired by: The Nomads
directories to a different parent directory always failed. This bug
was caused by 4.4Lite2 changing the directory format and ext2fs not
keeping up.
Should be in 2.2.
This follows more closely the suggestions in the latest NCR docs, and has
been running on my system for weeks with no problem. It does improve the
quality of diagnostic messages and does allow to better understand the
sequence of events in case of an error.
This should go into 2.2 and 2.1.6.
This fixes several bugs and one missing feature:
- cluster_read() was needlessly used for reading files of size exactly 1
block.
- EFAULT errors for read didn't terminate the loop. This was probably
harmless.
- IO_VMIO handling was missing near line 275. I don't know what this does.
- B_CLUSTEROK was only set if (doclusterwrite) nead line 293. This was
harmless, if only because another bug prevents doclusterwrite from being
0.
- MNT_NOATIME wasn't implemented.
This should be in 2.2, of course.
Reviewed by: davidg
if I586_CPU is defined. Note there is a runtime check so the code
won't be run for non-Pentium CPUs anyway.
2.2 candidate, this code has been tested for almost half year in -current.
handlers if interrupts are nested more than a few (3) deep. This
only reduces the maximum nesting level by 1 with the standard
drivers unless there is a related bug somewhere, but can't hurt
much (the worst case is returning to hoggish interrupt handler like
wdintr(), but such interrupt handlers hurt anyway).
Fixed a previously harmless race incrementing the interrupt nesting
level.
This should be in 2.1.6 and 2.2.
medium with another size is being inserted. Right now, this case was
broken and led to a situation where a medium could only be replaced
with another one of the same size.
Closes PR #kern/1830: Can't mount optical disk...
Submitted by: akiyama@kme.mei.co.jp (Shunsuke Akiyama)
hardware interrupt counts add up to the total. Previously, software
interrupts generated by splz() were counted in the total. These
software interrupts seem to be very rare - there have apparently been
0 of them on freefall among the last 352448857 interrupts.
will be renamed.
Fixed comments about unsupported network protocols.
ncr0 is a controller, not a device. This make no difference.
Added undocumented options DEVFS_ROOT, I586_CTR_GUPROF and I586_PMC_GUPROF.
Sorted undocumented options.
. also detect the Phlips CDD2000; it's software-compatible with the HP part
Submitted by: cau@cc.gatech.edu (Carlos Ugarte)
. correct the blocksize handling for CD-DA tracks, and fix multitrack
handling
Submitted by: nsayer@quack.kfu.com (Nick Sayer)
2.2 candidates!
existing mechanism uses a global queue for some buffers and the
vp->b_dirtyblkhd queue for others. This turns sequential writes into
randomly ordered writes to the server, affecting both read and write
performance. The existing mechanism also copes badly with hung
servers, tending to block accesses to other servers when all the iods
are waiting for a hung server.
The new mechanism uses a queue for each mount point. All asynchronous
i/o goes through this queue which preserves the ordering of requests.
A simple mechanism ensures that the iods are shared out fairly between
active mount points. This removes the sysctl variable vfs.nfs.dwrite
since the new queueing mechanism removes the old delayed write code
completely.
This should go into the 2.2 branch.
7810 being either the last of the first device to be probed, so use a counting
scheme instead to determine when one card ends and another begins. There may
be a better way to do this by decoding the PCI tag, which I will investigate
later.
2.2 Candidate.
it automatically. The AHC_FORCE_PIO option wasn't having any effect because
the PCI probe code didn't include this file.
Fix some problems with the new sync and wide negotiation code. First off,
go back to async transfers by using a message reject again. The SCSI II and
III spec indicate that if a target's response to an initiater does not suit
(i.e. its too low), then performing a message reject is the appropriate
response. If, on the other hand, the initiator begins the negotiation and
we want to go async, we will send back an SDTR message with a 0 period and
offset.
Also fix a really bad negotiation problem caused by a missing "break". This
would usually hit people that had "smart" wide devices that immediately
attempt sync negotiation after a successful wide negotiation.
2.2 Candidate.
or list items which may look like devices but which don't have an
isa_device structure attached to them.
This _shouldn't_ be possible, but it appears to have been
observed-by: Joerg
problem of allocating contiguous buffer memory in general, but
make it much more likely to work at boot-up time. The best
chance for an LKM-type load of a sound driver is immediately
after the mount of the root filesystem.
This appears to work for a 64K allocation on an 8MB system.
3COM 3C590 Etherlink III PCI,
3COM 3C595 Fast Etherlink PCI,
3COM 3C592 Etherlink III EISA,
3COM 3C590 Fast Etherlink EISA,
3COM 3C900 Etherlink XL PCI and
3COM 3C905 Fast Etherlink XL PCI.
This driver is based on OpenBSD's driver. I modified it to run under FreeBSd
and made it actually work usefully.
Afterwards, nao@tom-yam.or.jp (HAMADA Naoki) added EISA support as well as
early support for 3C900 Etherlink XL PCI and 3C905 Fast Etherlink XL PCI.
He also split up the driver in a bus independant and bus dependant parts.
Especially the 3c59X support should be pretty stable now.
Submitted by: partly nao@tom-yam.or.jp (HAMADA Naoki)
Obtained from:partly OpenBSD
1. When a directory is renamed to an existing (empty) directory,
it is possible for the target vnode to become the source vnode
underneath you (because another process may complete the same
rename). It was assumed that this can't happen, and the bogus
errno EINVAL was returned. This was fairly harmless.
Fix: return ENOENT instead, as if the source directory was renamed
a little earlier.
2. The same metamorphosis is possible for non-directories. It was
assumed that this can't happen, and the code for handling "just
removing a link name" happened to be used. This would have worked
except for fatal bugs in the link name removal - the link name was
assumed to still be there, and a null pointer was followed.
Fix: check the result of relookup(). This fixes PR 1930.
Notes:
(a) POSIX seems to say that removing link names shall have no effect.
BSD (4.4Lite2 at least) does something reasonable instead.
(b) The relookup() may find a file unrelated to the original.
Removing this isn't correct. Consider 3 existing files A, B and
C, and concurrent renames: AB = rename(A, B), another AB, and
CA = rename("c", "a"). If rename() is atomic, then only the
following results are possible:
AB, AB (fails), CA: A = original C, B = original A, C = gone
AB, CA, AB: A = gone, B = original C, C = gone
CA, AB, AB (fails): A = gone, B = original C, C = gone
but ufs_rename() can give:
A,AB,CA,B (sorta): A = gone, B = original A, C = gone
This usually doesn't matter, since getting into a race is usually
an error.
---
These fixes should be in 2.1.6 and 2.2.
mappings with mlock. This problem only occurred because of the
quick unmap code not respecting the wired-ness of pages in the
process. In the future, we need to eliminate the dependency
intrinsic to the design of the code that wired pages actually
be mapped. It is kind-of bogus not to have wired pages mapped,
but it is also a weakness for the code to fall flat because
of a missing page.
This show fix a problem that Tor Egge has been having, and also
should be included into 2.2-RELEASE.
appearance of this bug was the malfunctioning -M option in GNU tar (it
worked only by explicitly specifying -L).
Reviewed by: bde, and partially corrected accoring to his comments
Candidate for 2.2, IMHO even for 2.1.6.
changes to the keyboard code in pcvt, this update_led() very often
caused pcvt to hang early at boot time.
(Eventually, a better solution should be found, but the simple
omission serves well as a workaround for something that is actually a
show-stopper class problem.)
Candidate for 2.2.
(1) deleted #if 0
pc98/pc98/mse.c
(2) hold per-unit I/O ports in ed_softc
pc98/pc98/if_ed.c
pc98/pc98/if_ed98.h
(3) merge more files by segregating changes into headers.
new file (moved from pc98/pc98):
i386/isa/aic_98.h
deleted:
well, it's already in the commit message so I won't repeat the
long list here ;)
Submitted by: The FreeBSD(98) Development Team
"high" and "secure"), we can't use a single variable to track the most
recently used port in all three ranges.. :-] This caused the next
transient port to be allocated from the start of the range more often than
it should.
If DEVFS is configured, create devfs devices for previously invisible
partitions on the slices.
Fixed an old aliasing bug which caused E=17 errors from DEVFS for
DIOCSDINFO when there were no real slices.
(1) Add #ifdef PC98:
sys/pc98/boot/biosboot/boot2.S
(2) Fix bug that made it impossible to boot from sd's other than unit 0:
sys/pc98/boot/biosboot/sys.c
(3) Delete redundant $Id$:
sys/pc98/pc98/clock.c (reject$B$5$l$k$+$b$7$l$J$$(B)
(4) unt -> u_int:
sys/pc98/pc98/if_ed.c
(5) Add support for rebooting by the hot-key sequence:
sys/pc98/pc98/kbdtables.h
(6) Display now looks like PC/AT version:
sys/pc98/pc98/npx.c
(7) Change comment to match that of PC/AT version:
sys/pc98/pc98/pc98.c
(8) Add function prototypes:
sys/pc98/pc98/pc98_machdep.c
(9) Include PC98 headers:
sys/pc98/pc98/sound/adlib_card.c
sys/pc98/pc98/sound/audio.c
sys/pc98/pc98/sound/dev_table.c
sys/pc98/pc98/sound/dmabuf.c
sys/pc98/pc98/sound/midi_synth.c
sys/pc98/pc98/sound/midibuf.c
sys/pc98/pc98/sound/opl3.c
sys/pc98/pc98/sound/oatmgr.c
sys/pc98/pc98/sound/sb16_dsp.c
sys/pc98/pc98/sound/sb16_midi.c
sys/pc98/pc98/sound/sb_card.c
sys/pc98/pc98/sound/sb_dsp.c
sys/pc98/pc98/sound/sb_midi.c
sys/pc98/pc98/sound/sb_mixer.c
sys/pc98/pc98/sound/sequencer.c
sys/pc98/pc98/sound/sound_config.h
sys/pc98/pc98/sound/sound_switch.c
sys/pc98/pc98/sound/soundcard.c
sys/pc98/pc98/sound/sys_timer.c
(10) Merge in PC98 changes:
sys/i386/isa/sound/os.h
(11) Deleted as result of 9. and 10. above:
sys/pc98/pc98/sound/ad1848_mixer.h
sys/pc98/pc98/sound/aedsp16.c
sys/pc98/pc98/sound/coproc.h
sys/pc98/pc98/sound/finetune.h
sys/pc98/pc98/sound/gus_hw.h
sys/pc98/pc98/sound/gus_linearvol.h
sys/pc98/pc98/sound/hex2hex.h
sys/pc98/pc98/sound/mad16.h
sys/pc98/pc98/sound/midi_ctrl.h
sys/pc98/pc98/sound/midi_synth.h
sys/pc98/pc98/sound/opl3.h
sys/pc98/pc98/sound/os.h
sys/pc98/pc98/sound/pas.h
sys/pc98/pc98/sound/sb_mixer.h
sys/pc98/pc98/sound/soundvers.h
sys/pc98/pc98/sound/tuning.h
Submitted by: The FreeBSD(98) Development Team
Check that a received packet isn't longer than MCLBYTES. This will
sometimes happen if a cable is plugged into or removed from a live
system.
Try to cater better for early receive interrupts.
used mvi instead of mov. Luckily this code is most likely never executed
since it is only there for sanity should a target goes into the data phase
twice during a single selection or reselection.
This involves expanding the support of the SEEPROM routines to deal with
the larger SEEPROMs on these cards and providing a mechanism to share
SCB arrays between multiple controllers.
Most of the 398X support came from Dan Eischer.
ahc_data -> ahc_softc
Clean up some more type bogons I missed from the last pass.
This involves expanding the support of the SEEPROM routines to deal with
the larger SEEPROMs on these cards and providing a mechanism to share
SCB arrays between multiple controllers.
Most of the 398X support came from Dan Eischer.
ahc_data -> ahc_softc
Clean up some more type bogons I missed from the last pass.
Be more clear when handing the NO_MATCH condition. NO_MATCH can also
happen when the sequencer encounters an SCB we've asked to be aborted.
AHC_FORCE_PIO - This forces the driver to use PIO even on systems that
say they have memory mapped the controller's registers. This
seems to fix Ken Lam's problems. I've also placed this option
in the GENERIC kernel file so that we are guaranteed to install
even on these flakey machines.
AHC_SHARE_SCBS - This option attempts to share the external SCB SRAM on
the 398X controllers allowing a totoll of 255 non-paged SCBs.
This doesn't work quite yet, so this option is mostly here to
help 398X owners to experiment and give me feedback until this
works properly.
it breaks in the DEVFS_ROOT case. replicate a bit too much of bdevvp()
in here to circumvent the problem. The real problem is the magic that
lives in bdevsw[1].
TIMER_FREQ.
Fixed missing splx() in scrn_timer(). The bug was harmless because of the
undocumented behaviour that the ipl is automatically restored for timeout
functions (see softclock()). Perhaps we should depend on this behaviour.
Fixed the ddb fix in rev.1.176. The in_debugger flag was no use because
it only works when the debugger is entered via the keyboard hotkey. The
debugger may be entered for breakpoints and traps, and the console putc
routine has no way of knowing when it was, so the console putc routine
must (almost?) always remove the cursor image.
Not fixed: console switching in ddb doesn't work (ISTR it working), and
console 0 shouldn't be switched to for the debugger hotkey unless console
0 is /dev/console.
Fixed side effects from calling add_keyboard_randomness() in the console
getc routine by not calling it. add_keyboard_randomness() currently
always reenables interrupts on 386's and 486's. This is very bad if the
console getc routine is called from the debugger and the debugger was
entered with interrupts disabled.
Fixed preservation of initial screen and now-bogus comment about it. It
was broken by setting the initial scr_buf to `buffer' instead of Crtat.
`buffer' was full of nulls and the first scroll cleared everything above
the things written through syscons.
Submitted by: bruce (bde@freebsd.org)
I decided to do this for every hardclock() call instead of lazily
in microtime(). The lazy method is simpler but has more overhead
if microtime() is called a lot.
CPU_THISTICKLEN() is now a no-op and should probably go away.
Previously it did nothing directly but had the side effect of
setting i586_last_tick for CPU_CLOCKUPDATE() and i586_avg_tick for
debugging. CPU_CLOCKUPDATE() now uses a better method and
i586_avg_tick is too much trouble to maintain.
Reduced nesting of #includes in the usual case.
Increased nesting of #includes when CLOCK_HAIR is defined. This
is a kludge to get typedefs for inline functions only when the
inline functions are used. Normally only kern_clock.c defines
this. kern_clock.c can't include the i386 headers directly.
Removed unused LOCORE support.
break when I remove LOCORE support from clock.h.
I586_CTR_MULTIPLIER_SHIFT = 32 from clock.h is actually still used, but
32 is so magic that it doesn't get used explicitly.
- Add support for memory mapped I/O.
- Use DMA to get SCBs down to the adapters.
- Remove old paging code.
- Be much smarter about how we allocate SCB space. The old, simple method
wasted almost half a page per SCB. Ooops.
- Make command complete interrupt processing more efficient.
- Break the monolithic ahc_intr into sub-routines. The sub-routines handle
rare, special case events so the function call is not a penalty and the
removal of the code from the main routine most likely improves performance
instruction prefech will work better and less code is pushed into the cache.
- Never, ever allow tagged queueing if a device has disconnection disabled.
- Clean up and simplify timeout code. Many of the changes are to handle the
new DMA scheme.
SCB paging is now handled almost entirely by the sequencer and also uses
DMA. This should make SCB paging at least an order of magnitude more
efficient and vastly simplifies the implementation.
Add a few space optimizations so this code still fits on aic7770 chips.
Update comments.
Submitted by: whistle communications
move the socket from /dev to /var/run by default
TRANSITIONALLY make syslog add a symlink..
I PROMISE I'll remove that as soon as I have the makefiles etc fixed as well.
1) Rename FNM_ICASE to FNM_CASEFOLD
2) Add FNM_LEADING_DIR
Add proper (unsigned char) casts to tolower().
Use 'char' function argument for proper sign extension
bit (0x0008) in the sc driver configuration line. This way it's easy to
boink a generic kernel.
Also, document and place in an opt_ file the #define's for overriding which
serial port is the system console.
Approved by: sos
(1) Bug fix (pass boot drive):
pc98/boot/biosboot/boot2.S
(2) Delete code for unsupported high-resolution modes and move old
Epson notebook code to epsonio.h:
pc98/boot/biosboot/io.c
pc98/i386/vm_machdep.c
pc98/pc98/fd.c
pc98/pc98/pc98.c
pc98/pc98/pc98.h
pc98/pc98/epsonio.h (new)
(3) Change aic driver so that PCMCIA cards (I/O port same as PC/AT)
and PC-9801-100 cards can be selected with a flag in kernel config
file:
pc98/pc98/aic6360.c
pc98/pc98/aic_98.h (new)
(4) Fix wcd entry (it was broken). Delete mcd, it doesn't work on
98. Change aic entry according to above:
pc98/conf/GENERIC98
(5) Move pc98_machdep.c to top of files in pc98/pc98:
pc98/conf/files.pc98
(6) Delete empty lines:
pc98/i386/locore.s
(7) Fix (it didn't work if I586 was specified):
pc98/pc98/clock.c
(8) Staticize:
pc98/pc98/pc98_machdep.c
(9) Enable workaround for Cyrix bug for 5x86 also:
pc98/i386/machdep.c
pc98/i386/trap.c
All the above deletes this file too:
pc98/i386/pmap.c
(phew!)
Submitted by: The FreeBSD(98) Development Team
Garrett Wollman sent me this code a few weeks ago for review, and I made
some significant changes, which he in turn accepted ...
In order to make use of these changes, a device entry has to added to /dev.
Submitted by: wollman
following warning:
warning: ANSI C forbids braced-groups within expressions
Adding __extension__ before the statement-expression seems to work right.
Submitted by: bde (a *long* time ago)
contents are discarded, including the cached seek cookies.
Unfortunately, if the directory was larger than NFS_DIRBLKSIZ, then
this confused nfs_readdirrpc(), making it appear as if the directory
was truncated.
Reviewed by: Karl Denninger <karl@Mcs.Net>
there is keyboard input.
The mousepointer is shown again immediately if moved.
Also a function pointer used to install a userwritten extra
ioctl handler (sc_user_ioctl). This way its is possible to
install user defined videomodes etc etc. No further changes
should be in the kernel.
- use a more accurate and more efficient method of compensating for
overheads. The old method counted too much time against leaf
functions.
- normally use the Pentium timestamp counter if available.
On Pentiums, the times are now accurate to within a couple of cpu
clock cycles per function call in the (unlikely) event that there
are no cache misses in or caused by the profiling code.
- optionally use an arbitrary Pentium event counter if available.
- optionally regress to using the i8254 counter.
- scaled the i8254 counter by a factor of 128. Now the i8254 counters
overflow slightly faster than the TSC counters for a 150MHz Pentium :-)
(after about 16 seconds). This is to avoid fractional overheads.
files.i386:
permon.c temporarily has to be classified as a profiling-routine
because a couple of functions in it may be called from profiling code.
options.i386:
- I586_CTR_GUPROF is currently unused (oops).
- I586_PMC_GUPROF should be something like 0x70000 to enable (but not
use unless prof_machdep.c is changed) support for Pentium event
counters. 7 is a control mode and the counter number 0 is somewhere
in the 0000 bits (see perfmon.h for the encoding).
profile.h:
- added declarations.
- cleaned up separation of user mode declarations.
prof_machdep.c:
Mostly clock-select changes. The default clock can be changed by
editing kmem. There should be a sysctl for this.
subr_prof.c:
- added copyright.
- calibrate overheads for the new method.
- documented new method.
- fixed races and and machine dependencies in start/stop code.
mcount.c:
Use the new overhead compensation method.
gmon.h:
- changed GPROF4 counter type from unsigned to int. Oops, this should
be machine-dependent and/or int32_t.
- reorganized overhead counters.
Submitted by: Pentium event counter changes mostly by wollman
add free vnodes back to the freelist. They must do their own vnode
management. Anyway, this change is *only* activated with their filesystem
and doesn't affect anyone else. Whoops, forgot the submitted-by lines
in my previous commits too.. :-(
Submitted-By: Tony Ardolino <tony@netcon.com>
The heuristic for managment of memory backing the buffer cache was
nice, but didn't work due to some architectural problems. Simplify
and improve the algorithm.
- use CROSSJUMP() and CROSSJUMP_LABEL() for conditional jumps from idle()
into cpu_switch() and vice versa.
- moved badsw code to after cpu_switch().
Cosmetic changes:
- moved sw0 string to be immediately after its caller (badsw).
- removed unused #include.
the one place that depended on it. wakeup() is now prototyped in
<sys/systm.h> so that it is normally visible.
Added nested include of <sys/queue.h> in <vm/vm_object.h>. The queue
macros are a more fundamental prerequisite for <vm/vm_object.h> than
the wakeup prototype and previously happened to be included by
namespace pollution from <sys/proc.h> or elsewhere.
controllers, it is an error to issue a command before the keyboard
has had time to reply to the previous command. Setting the LEDs
involves issueing 2 commands, so it never worked on these keyboards.
Fixed resetting of keyboard. It is possible for unprocessed
scancodes to be present when the reset routine is called. This
usually occurs after switching from one console driver to another
in userconfig. pcvt and syscons attempt to flush any stale scancodes,
but sometimes fail to do so because keyboard and/or keyboard
controller takes a long time to send the scancodes after reset
(scancodes are apparently not flushed by reset!). syscons handles
this later by not checking for errors at strategic places, but pcvt
was confused.
Use an impossible initial and failure mode setting for the LEDs
so that the LEDs always get set if they are possibly out of sync.
Added missing spltty() in update_led().
shipped with freebsd can be changed without modifying the Makefiles directly.
Creates: BOOT_FORCE_COMCONSOLE
BOOT_PROBE_KEYBOARD
BOOT_PROBE_KEYBOARD_LOCK
BOOT_COMCONSOLE (port value for console)
