o Don't run through the register initialization in the read mac routine
for the AX88x90. It duplicates other stuff that we do.
o Eliminate the 10ms delay after we reset the AX88x90. We already wait for
the appropriate bits to indicate reset is done.
a device specific DMA tag. On amd64 it could exhaust all of bounce
pages when bus_dma_tag_create(9) is called at malo_pci_attach() then as
result in next turn it returns ENOMEM. This fix a attach fail on amd64.
Pointed by: yongari
Tested by: dchagin
MFC after: 3 days
It seems that RTL8168D and RTL8102EL requires additional settle
time to complete RL_PHYAR register write. Accessing RL_PHYAR
register right after the write causes errors for subsequent PHY
register accesses.
Tested by: george at luckytele dot com,
Steve Wills < STEVE at stevenwills dot com >
don't have one of the clock cycles (the turn cycle) that the AX88x90
chips have. Make this conditional. But this seems totally crazy and
can't possibly be right. Commit the fix for the moment until I can
explore this mystery more deeply.
On the plus side, the DL10022-based cards I have (D-Link DEF-670TXD
and SMC8040TX) work after this fix.
Add ch_suspend/ch_resume methods for PCI controllers and implement them
for AHCI. Refactor AHCI channel initialization according to it.
Fix Port Multipliers operation. It is far from perfect yet, but works now.
Tested with JMicron JMB363 AHCI + SiI 3726 PMP pair.
Previous version was also tested with SiI 4726 PMP.
Hardware sponsored by: Vitsch Electronics / VEHosting.nl
o call ieee80211_encap in ieee80211_start so frames passed down to drivers
are already encapsulated
o remove ieee80211_encap calls in drivers
o fixup wi so it recreates the 802.3 head it requires from the 802.11
header contents
o move fast-frame aggregation from ath to net80211 (conditional on
IEEE80211_SUPPORT_SUPERG):
- aggregation is now done in ieee80211_start; it is enabled when the
packets/sec exceeds ieee80211_ffppsmin (net.wlan.ffppsmin) and frames
are held on a staging queue according to ieee80211_ffagemax
(net.wlan.ffagemax) to wait for a frame to combine with
- drivers must call back to age/flush the staging queue (ath does this
on tx done, at swba, and on rx according to the state of the tx queues
and/or the contents of the staging queue)
- remove fast-frame-related data structures from ath
- add ieee80211_ff_node_init and ieee80211_ff_node_cleanup to handle
per-node fast-frames state (we reuse 11n tx ampdu state)
o change ieee80211_encap calling convention to include an explicit vap
so frames coming through a WDS vap are recognized w/o setting M_WDS
With these changes any device able to tx/rx 3Kbyte+ frames can use fast-frames.
Reviewed by: thompsa, rpaulo, avatar, imp, sephe
o Introduce new chip_type AX88790. There's a few places we need to know the
exact chip for workaronds.
o Explain the AX88190 workaround for the ISR bits being stuck, and don't
apply them to the AX88790. The datasheet says the bits are fixed, and
experience confirms.
o Fix mii bit-bang read code to read and discard the 'floating' bit.
o Remove empty ed_pccard_ax88x90_mii_reset routine
o Report error from mii_phy_probe
o Don't use ed_probe_Novel_generic for ax88x90 chips. It puts them into
an odd state sometimes. Instead, use a more stream-lined version that
avoids the trouble spots. This was copied and tweaked from the original.
o Move chip reset into its own routine.
o Minor code optimiation on getting MAC address
o Add code for coping with AX88790 cards that are in power down state and
need to be kicked before the PHY registers for the internal phy read right.
o Remove ugly cap of PHYs at 17.
o For AX88790, we need to set a special bit for accessig phy 16 (the internal
phy) and clear it for all others according to a chip erratum.
o streamline the bit-bang code for AX88x90: the delays aren't needed according
to the datasheet timing diagrams and also the Linux driver
o Fix minor bit definition for direction bit.
o Generally: Some comments reformatted
o Only try the toshiba probe on cards labelled as toshiba
# From another Akihabara card (this one from a few years ago from a
# friend in Japan). Fix the Corega FEther II PCC-TXD. This one is
# still on sale new, as of a few weeks ago. should fix all other AX88x90
# based cards, but I have some testing left to finish on my collection...
o remove ic_myaddr from ieee80211com
o change ieee80211_ifattach to take the mac address of the physical device
and use that to setup the lladdr.
o replace all references to ic_myaddr in drivers by IF_LLADDR
o related cleanups (e.g. kill dead code)
PR: kern/133178
Reviewed by: thompsa, rpaulo
It seems that some revision of controller hang while accessing
the VPD. Because VPD access routine are unused, nuke it.
o Let TWSI reload EEPROM if VPD capability is detected. Reloading
EEPROM will also set ethernet address so age(4) now reads AGE_PAR0
and AGE_PAR1 register to get ethernet address. This removes a lot
of hack and enhance readability a lot.
o Double PHY reset timeout as it takes more time to take PHY out of
power-saving state.
o Explicitly check power-saving state by checking undocumented PHY
registers. If link is not up, poke undocumented registers to take
PHY out of power-saving state. This is the same way what Linux
does. On resume, make sure to wake up PHY.
o Don't rely on auto-clearing feature of master reset bit, just wait
1ms and check idle status of MAC.
o Add PCI device revision information in bootverbose mode.
This should fix occasional controller hang in device attach phase.
Reported by: barbara < barbara.xxx1975 at libero DOT it >
Tested by: barbara < barbara.xxx1975 at libero DOT it >
up) rather than amount + 1 / 2, which is the same as amount, or 2x too
many words which leads to data corruption.
# This fixes the sbdrop panics I was seeing with the Toshiba LANCT00A.
Toshiba PCETC ISA card, and even has the same board type code in the
card ID (0x14). So, for this card, call ed_probe_WD80x3_generic after
setting things up apropriately. This makes the card attach and kinda
work (I'm seeing panics in sbdrop). Since history has shown that the
WD80x3 probe routine is dangerous, only do it for this card. Also,
disable the memory range check to make sure it is an valid ISA memory.
I think that it is bogus, but I'm not 100% sure, for these cards.
I removed probing for the WD80x3 in 2005 when I added support for the
AX88x90 and DL100xx cards since none of my cards had ever matched it
and PAO3 removed it and none of the cards in their database died.
It is possible there are other quirks about this card too, since no
other open source OS supports it, or even claims to support it. But
it was a fun half hour hack...
driver. Not sure who sold it/rebadged it.
Add stub entries for Mitsubishi B8895 and Toshiba LANCT00A to the
driver with a comment that they don't work /* NG */.[*] These are
DP83902A based cards, which should work, but don't seem to. Likely
they are from the days before the ne2000 roamed the earth and use a
non-standard hookup (see if_ed_isa or if_ed_cbus for some examples).
Unless I happen to stumble into the right one, these may never work,
but I'm tired of omitting them from commits.
[*] The Japanese adopted OK from English, but also use NG for its
opposite.
rather than behind a seemingly accidental constant likely left over from one of
the related drivers which uses log levels rather than per-facility debugging
flags. This should get rid of contextless messages on the console for people
who have not set (or cleared the default) debugging flags.
packet. Linux, OpenBSD and our iwn(4) all do this. It also results in
a huge performance improvement (and the rejection of a fair number of
apparently-bad packets on receive) on my hardware.
o) Like the wpi(4) driver in OpenBSD, and like our iwn(4), also drop runt
packets.
o) Don't bother doing IFQ_POLL and then IFQ_DRV_DEQUEUE, just do
IFQ_DRV_DEQUEUE outright. This is more similar to how OpenBSD and our
iwn(4) work.
Reviewed by: sam
into acpi_cpu_startup() which is where all the other code to update this
global variable lives. This fixes a bug where cpu_cx_count was not updated
correctly if acpi_cpu_generic_cx_probe() returned early.
PR: kern/108581
Debugged by: Bruce Cran
Reviewed by: avg, njl, sepotvin
MFC after: 3 days
via the Linux tool.
- Add Linux shim to ipmi(4)
- Create a partitions file to linprocfs to make Linux fdisk see
disks. This file is dynamic so we can see disks come and go.
- Convert msdosfs to vfat in mtab since Linux uses that for
msdosfs.
- In the Linux mount path convert vfat passed in to msdosfs
so Linux mount works on FreeBSD. Note that tasting works
so that if da0 is a msdos file system
/compat/linux/bin/mount /dev/da0 /mnt
works.
- fix a 64it bug for l_off_t.
Grabing sh, mount, fdisk, df from Linux, creating a symlink of mtab to
/compat/linux/etc/mtab and then some careful unpacking of the Linux bmc
update tool and hacking makes it work on newer Dell boxes. Note, probably
if you can't figure out how to do this, then you probably shouldn't be
doing it :-)
When a vt switch occurs the irq handler is uninstalled. Interrupts
and the state tracking of what was enabled/disabled wasn't working
properly. This should resolve the reports of "slow windows" after a
vt switch, among other things. The radeon 2d driver seems to work a
bit more correctly than the Intel driver. With the Intel driver,
vblank interrupts will be enabled at system startup and will only
be disabled after an additional modeset (vt switch, dpms, randr event).
With this patch, I am able to run glxgears synced to vblank and
vt switch while it is running without ill effects.
MFC after: 3 days
