don't implement link power management, LPM.
This fixes error code XHCI_TRB_ERROR_BANDWIDTH for isochronous USB 3.0
transactions.
Submitted by: Horse Ma <Shichun.Ma@dell.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
snd_hda was rewritten in r230130; one function retained a comment
referencing the previous name.
MFC after: 3 days
Sponsored by: The FreeBSD Foundation
A later change, currently being iterated on in D24459, will in-fact change
the lock type to an sx so that TTY drivers can sleep on it if they need to.
Committing this ahead of time to make the review in question a little more
palatable.
tty_lock_assert() is unfortunately still needed for now in two places to
make sure that the tty lock has not been recursed upon, for those scenarios
where it's supplied by the TTY driver and possibly a mutex that is allowed
to recurse.
Suggested by: markj
On my Dell Latitude 7390 laptop, the brightness hotkeys
(Fn+<up/down arrow>) send ACPI notifications which acpi_video
handles by adjusting its brightness setting; but ACPI does not
actually do anything with the backlight.
Announcing brightness changes via devd makes it possible to close
the loop by triggering the intel_backlight utility to perform the
required backlight adjustment.
Reviewed by: imp
MFC after: 3 days
Differential Revision: https://reviews.freebsd.org/D24424
Name each ehci driver uniquely.
This remove the warning printed at each arm boot :
module_register: cannot register simplebus/ehci from kernel; already loaded from kernel
A similar fix was done in r333074 but imx_ehci wasn't renamed and generic_ehci wasn't
present at that time.
KTLS uses the flowid to distribute software encryption tasks among its
pool of worker threads. Without this change, all software KTLS
requests for TOE sockets ended up on the first worker thread.
Note that the flowid for TOE sockets created via connect() is not a
hash of the 4-tuple, but is instead the id of the TOE pcb (tid). The
flowid of TOE sockets created from TOE listen sockets do use the
4-tuple RSS hash as the flowid since the firmware provides the hash in
the message containing the original SYN.
Reviewed by: np (earlier version)
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24348
This fixes a panic when unloading and reloading t4_tom.ko since the
old pointer is still stored when t4_tom_load tries to set it.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24358
This pattern is used in callbacks with void * data arguments and seems
both relatively uncommon and relatively harmless. Silence the warning
by casting through uintptr_t.
This warning is on by default in Clang 11.
Reviewed by: arichardson
Obtained from: CheriBSD (partial)
MFC after: 1 week
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24425
If the fdt node doesn't have a cd-gpios properties or if the node is set
as non-removable we do not init the card detection timeout task as it is
useless so don't schedule it too.
MFC after: 1 month
X-MFC-With: r359924
This fixes a panic that would occur when the timer tried to close a
stale socket.
Submitted by: Krishnamraju Eraparaju @ Chelsio
MFC after: 1 week
Sponsored by: Chelsio Communications
Copy the CP, PTRIN, etc macros from freebsd32.h into a sys/abi_compat.h
and replace existing definitation with includes where required. This
eliminates duplicate code and allows Linux and FreeBSD compatability
headers to be included in the same files.
Input from: cem, jhb
Obtained from: CheriBSD
MFC after: 2 weeks
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24275
the dts to find the supported speeds and the regulators.
Not all DTS have every settings properly defined so host controller
will still have to add some caps themselves.
It also add a mmc_fdt_gpio_setup function which will read the cd-gpios
property and register it as the CD pin.
If the pin support interrupts one will be registered and the cd_helper
function will be called.
If the pin doesn't support interrupts the internal taskqueue will poll
for change and call the same cd_helper function.
mmc_fdt_gpio_setup will also parse the wp-gpio property and MMC drivers
can know the write-protect pin value by calling the
mmc_fdt_gpio_get_readonly function.
MFC after: 1 month
Differential Revision: https://reviews.freebsd.org/D23267
While the original implementation of unmapped mbufs was a large
step forward in terms of reducing cache misses by enabling mbufs
to carry more than a single page for sendfile, they are rather
cache unfriendly when accessing the ext_pgs metadata and
data. This is because the ext_pgs part of the mbuf is allocated
separately, and almost guaranteed to be cold in cache.
This change takes advantage of the fact that unmapped mbufs
are never used at the same time as pkthdr mbufs. Given this
fact, we can overlap the ext_pgs metadata with the mbuf
pkthdr, and carry the ext_pgs meta directly in the mbuf itself.
Similarly, we can carry the ext_pgs data (TLS hdr/trailer/array
of pages) directly after the existing m_ext.
In order to be able to carry 5 pages (which is the minimum
required for a 16K TLS record which is not perfectly aligned) on
LP64, I've had to steal ext_arg2. The only user of this in the
xmit path is sendfile, and I've adjusted it to use arg1 when
using unmapped mbufs.
This change is almost entirely mechanical, except that we
change mb_alloc_ext_pgs() to no longer allow allocating
pkthdrs, the change to avoid ext_arg2 as mentioned above,
and the removal of the ext_pgs zone,
This change saves roughly 2% "raw" CPU (~59% -> 57%), or over
3% "scaled" CPU on a Netflix 100% software kTLS workload at
90+ Gb/s on Broadwell Xeons.
In a follow-on commit, I plan to remove some hacks to avoid
access ext_pgs fields of mbufs, since they will now be in
cache.
Many thanks to glebius for helping to make this better in
the Netflix tree.
Reviewed by: hselasky, jhb, rrs, glebius (early version)
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D24213
uart(4) backends currently detect RX FIFO overrun errors and report
them to the uart(4) core layer. They are then reported to the generic
TTY layer which promptly ignores them. As a result, there is
currently no good way to determine if a uart is experiencing RX FIFO
overruns. One could add a generic per-tty counter, but there did not
appear to be a good way to export those. Instead, add a sysctl under
the uart(4) sysctl tree to export the count of overruns.
Reviewed by: brooks
MFC after: 2 weeks
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24368
Shifting right by 1 is not the same as dividing by 2 for signed
values. In particular, dividing a signed value by 2 gives the integer
ceiling of the (e.g. -5 / 2 == -2) whereas shifting right by 1 always
gives the floor (-5 >> 1 == -3).
An embedded board with a 25 Mhz base clock results in an error of
-30.5% when used with a baud rate of 115200. Using division, this
truncates to -30% and is permitted. Using the shift, this fails and
is rejected causing TIOCSETA requests to fail with EINVAL and breaking
getty(8).
Using division gives the same error range for both over and under baud
rates and also makes the code match the behavior documented in the
existing comment about supporting boards with 25 Mhz clocks.
Reported by: imp
MFC after: 2 weeks
Sponsored by: DARPA
Differential Revision: https://reviews.freebsd.org/D24367
A T6 adapter contains two crypto engines on separate channels. This
commit distributes sessions between the two engines. Previously, only
the first engine was used.
Reviewed by: np
Sponsored by: Chelsio Communications
Differential Revision: https://reviews.freebsd.org/D24347
There are several reports of "hdac0: Command timeout on address 2"
messages emitted during playback on a variety of contemporary machines.
Show the command that timed out in case it might provide a clue in
finding the cause.
PR: 229190
MFC after: 1 week
Sponsored by: The FreeBSD Foundation
The comment previously stated the delay must be at least 250us but that
was insufficient and so should be doubled, but the delay was actually
1000. The HDA spec actually says the delay must be 521 us (25 frames)
so update the comment to match.
Recognize new micro-architecture in hwpmc_intel driver. Based on Intel
document 325462-071US. Tested with tools/test/hwpmc/pmctest.py
on Atom E3930 SoC.
Submitted by: Dawid Gorecki <dgr@semihalf.com>
Reviewed by: kib
Obtained from: Semihalf
Sponsored by: Stormshield
Differential Revision: https://reviews.freebsd.org/D24310
When using SACK it can happen there are multiple option headers.
Don't drop these packets, but instead limit the amount of inlining
to the maximum supported.
MFC after: 1 week
Sponsored by: Mellanox Technologies
This includes 14 bytes of ethernet header and 2 bytes of VLAN header.
This allows for making assumptions about the inline size limit
in the fast transmit path later on.
Use a signed integer variable to catch underflow.
MFC after: 1 week
Sponsored by: Mellanox Technologies
The reporter is developing a frame buffer driver for hardware using
3 bytes per pixel, but a stride that's a multiple of 256. Previously
this resulted in writing beyond the end of each stride. On the last
row this attempted to write past the end of the frame buffer, triggering
the assertion in vt_fb_mem_wr1().
PR: 243533
MFC after: 2 weeks
Submitted by: Thomas Skibo
This is mostly indentation whitespace, and reflowing a few multiline
comments. This gets a bunch of minor stuff out of the way so that the diffs
for style don't clutter up the diffs for some upcoming functional changes.
Submitted by: Thomas Skibo
Differential Revision: https://reviews.freebsd.org/D24226
This driver hasn't been relevant in almost 15 years. It was for a product on the
shelves for about 6 months in 2003/2004. I've not updated the driver since then,
and have had nobody talk to me about it since maybe 2006 or 2007. It doesn't
implement a standard interface, and can be better done with libusb. All the
action has moved to webcamd for newer, more fully featured hardware. It makes no
appearances in the nycbug dmesg archive.
Relnotes: yes
MFC After: 3 days
This allows clean handoff from BIOS implementing some asynchronous I/O to
the OS AHCI driver. During attach driver declares OS ownership request
and waits from 25ms to 2s for BIOS to complete operation and release the
hardware.
MFC after: 2 weeks
JMB582 has 2 6Gbps SATA ports and PCIe 3.0 x1.
JMB585 has 5 6Gbps SATA ports and PCIe 3.0 x2.
Both chips support AHCI v1.31, Port Multiplier with FBS and 8 MSI vectors.
MFC after: 2 weeks
