This framework allows drivers to abstract the rate control algorithm and
just feed the framework with the usable parameters. The rate control
framework will now deal with passing the parameters to the selected
algorithm. Right now we have AMRR (the default) and RSSADAPT but there's
no way to select one with ifconfig, yet.
The objective is to have more rate control algorithms in the net80211
stack so all drivers[0] can use it. Ideally, we'll have the well-known
sample rate control algorithm in the net80211 at some point so all
drivers can use it (not just ath).
[0] all drivers that do rate control in software, that is.
Reviewed by: bschmidt, thompsa, weyongo
MFC after: 1 months
o replace DLT_IEEE802_11 support in net80211 with DLT_IEEE802_11_RADIO
and remove explicit bpf support from wireless drivers; drivers now
use ieee80211_radiotap_attach to setup shared data structures that
hold the radiotap header for each packet tx/rx
o remove rx timestamp from the rx path; it was used only by the tdma support
for debugging and was mostly useless due to it being 32-bits and mostly
unavailable
o track DLT_IEEE80211_RADIO bpf attachments and maintain per-vap and
per-com state when there are active taps
o track the number of monitor mode vaps
o use bpf tap and monitor mode vap state to decide when to collect radiotap
state and dispatch frames; drivers no longer explicitly directly check
bpf state or use bpf calls to tap frames
o handle radiotap state updates on channel change in net80211; drivers
should not do this (unless they bypass net80211 which is almost always
a mistake)
o update various drivers to be more consistent/correct in handling radiotap
o update ral to include TSF in radiotap'd frames
o add promisc mode callback to wi
Reviewed by: cbzimmer, rpaulo, thompsa
Note this includes changes to all drivers and moves some device firmware
loading to use firmware(9) and a separate module (e.g. ral). Also there
no longer are separate wlan_scan* modules; this functionality is now
bundled into the wlan module.
Supported by: Hobnob and Marvell
Reviewed by: many
Obtained from: Atheros (some bits)
- Rename rt2560_read_eeprom to rt2560_read_config, we already have
rt2560_eeprom_read
- If hardware gives us wrong encryption done index, shout out loudly and
terminate the processing loop
- Process encryption done if RX done bit is set in interrupt status register
(according to Ralink Linux driver)
- Turn VALID/BUSY bits in TX descriptor only after TX descriptor is fully setup
- Fix BBP read: RT2560_BBPCSR can't be written until its RT2560_BBP_BUSY bit is
off (according to Ralink Linux driver)
- Skip invalid (0 of 0xffff) BBP register/value entries stored in EEPROM
- Fix channel TX power location in EEPROM, if channel TX power is above 31 set
it to 24 (TX power only has 5bits in RF register, "24" is according to Ralink
Linux driver)
- Configure BBP according to the BBP register/value stored in EEPROM, restore
BBP17 (RX sensitivity tuning) to default value after this.
- Set TX/RX antenna after BBP is initialized; these two operation will try to
set BBP registers
- Reconfigure ACK TX time registers according to 802.11g standard (TX @36Mb,
other side's ACK should be sent @24Mb).
- 2560 parts have two TX ring: one for management/control packets, one for data
packets. Add private OACTIVE flag for each of them. Turn on IFF_DRV_OACTIVE
if one of private OACTIVE is on; turn off IFF_DRV_OACTIVE iff all of them are
off.
- Rework watchdog to mimic old if_watchdog action. Process TX done/encryption
done in watchdog function (according to Ralink Linux driver)
Obtained from: DragonFly
Approved by: sam (mentor)
Tested by: sam
Related to PR: kern/117655
# Forcing long slot time setting is not included in this commit, comment and
# related code is in place, so if problem pops up, quick tests could be done.
o major overhaul of the way channels are handled: channels are now
fully enumerated and uniquely identify the operating characteristics;
these changes are visible to user applications which require changes
o make scanning support independent of the state machine to enable
background scanning and roaming
o move scanning support into loadable modules based on the operating
mode to enable different policies and reduce the memory footprint
on systems w/ constrained resources
o add background scanning in station mode (no support for adhoc/ibss
mode yet)
o significantly speedup sta mode scanning with a variety of techniques
o add roaming support when background scanning is supported; for now
we use a simple algorithm to trigger a roam: we threshold the rssi
and tx rate, if either drops too low we try to roam to a new ap
o add tx fragmentation support
o add first cut at 802.11n support: this code works with forthcoming
drivers but is incomplete; it's included now to establish a baseline
for other drivers to be developed and for user applications
o adjust max_linkhdr et. al. to reflect 802.11 requirements; this eliminates
prepending mbufs for traffic generated locally
o add support for Atheros protocol extensions; mainly the fast frames
encapsulation (note this can be used with any card that can tx+rx
large frames correctly)
o add sta support for ap's that beacon both WPA1+2 support
o change all data types from bsd-style to posix-style
o propagate noise floor data from drivers to net80211 and on to user apps
o correct various issues in the sta mode state machine related to handling
authentication and association failures
o enable the addition of sta mode power save support for drivers that need
net80211 support (not in this commit)
o remove old WI compatibility ioctls (wicontrol is officially dead)
o change the data structures returned for get sta info and get scan
results so future additions will not break user apps
o fixed tx rate is now maintained internally as an ieee rate and not an
index into the rate set; this needs to be extended to deal with
multi-mode operation
o add extended channel specifications to radiotap to enable 11n sniffing
Drivers:
o ath: add support for bg scanning, tx fragmentation, fast frames,
dynamic turbo (lightly tested), 11n (sniffing only and needs
new hal)
o awi: compile tested only
o ndis: lightly tested
o ipw: lightly tested
o iwi: add support for bg scanning (well tested but may have some
rough edges)
o ral, ural, rum: add suppoort for bg scanning, calibrate rssi data
o wi: lightly tested
This work is based on contributions by Atheros, kmacy, sephe, thompsa,
mlaier, kevlo, and others. Much of the scanning work was supported by
Atheros. The 11n work was supported by Marvell.
generations of 802.11abg chipsets from Ralink Technology.
Get rid of the pccard front-end while I'm here since all adapters are
cardbus ones.
Obtained from: OpenBSD
