opt_compat.h is mentioned in nearly 180 files. In-progress network
driver compabibility improvements may add over 100 more so this is
closer to "just about everywhere" than "only some files" per the
guidance in sys/conf/options.
Keep COMPAT_LINUX32 in opt_compat.h as it is confined to a subset of
sys/compat/linux/*.c. A fake _COMPAT_LINUX option ensure opt_compat.h
is created on all architectures.
Move COMPAT_LINUXKPI to opt_dontuse.h as it is only used to control the
set of compiled files.
Reviewed by: kib, cem, jhb, jtl
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14941
ARM Coresight is a solution for debug and trace of complex SoC designs.
This includes a collection of drivers for ARM Coresight interconnect
devices within a small Coresight framework.
Supported devices are:
o Embedded Trace Macrocell v4 (ETMv4)
o Funnel
o Dynamic Replicator
o Trace Memory Controller (TMC)
o CPU debug module
Devices are connected to each other internally in SoC and the
configuration of each device endpoints is described in FDT.
Typical trace flow (as found on Qualcomm Snapdragon 410e):
CPU0 -> ETM0 -> funnel1 -> funnel0 -> ETF -> replicator -> ETR -> DRAM
CPU1 -> ETM1 -^
CPU2 -> ETM2 -^
CPU3 -> ETM3 -^
Note that both Embedded Trace FIFO (ETF) and Embedded Trace Router (ETR)
are hardware configurations of TMC.
This is required for upcoming HWPMC tracing support.
This is tested on single-core system only.
Reviewed by: andrew (partially)
Sponsored by: DARPA, AFRL
Differential Revision: https://reviews.freebsd.org/D14618
This fixes a failure to resolve object file paths seen when buildkernel
(which sets MK_AUTO_OBJ=yes) and installkernel (which sets MK_AUTO_OBJ=no)
are run as separate steps. r329232 partially fixed this scenario by removing
MAKEOBJDIR, but it seems the AUTO_OBJ setting also needs to be on the same
page for the build and install steps.
Reviewed by: bdrewery
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D14143
The ocs_fc(4) driver supports the following hardware:
Emulex 16/8G FC GEN 5 HBAS
LPe15004 FC Host Bus Adapters
LPe160XX FC Host Bus Adapters
Emulex 32/16G FC GEN 6 HBAS
LPe3100X FC Host Bus Adapters
LPe3200X FC Host Bus Adapters
The driver supports target and initiator mode, and also supports FC-Tape.
Note that the driver only currently works on little endian platforms. It
is only included in the module build for amd64 and i386, and in GENERIC
on amd64 only.
Submitted by: Ram Kishore Vegesna <ram.vegesna@broadcom.com>
Reviewed by: mav
MFC after: 5 days
Relnotes: yes
Sponsored by: Broadcom
Differential Revision: https://reviews.freebsd.org/D11423
Mostly this is a thin shim around existing code to integrate with enc_xform
and cryptosoft (+ cryptodev).
Expand the cryptodev buffer used to match that of Chacha20's native block
size as a performance enhancement for chacha20_xform_crypt_multi.
illumos/illumos-gate@8671400134
The idea of Storage Pool Checkpoint (aka zpool checkpoint) deals with
exactly that. It can be thought of as a “pool-wide snapshot” (or a
variation of extreme rewind that doesn’t corrupt your data). It remembers
the entire state of the pool at the point that it was taken and the user
can revert back to it later or discard it. Its generic use case is an
administrator that is about to perform a set of destructive actions to ZFS
as part of a critical procedure. She takes a checkpoint of the pool before
performing the actions, then rewinds back to it if one of them fails or puts
the pool into an unexpected state. Otherwise, she discards it. With the
assumption that no one else is making modifications to ZFS, she basically
wraps all these actions into a “high-level transaction”.
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Dan Kimmel <dan.kimmel@delphix.com>
Approved by: Richard Lowe <richlowe@richlowe.net>
Author: Serapheim Dimitropoulos <serapheim.dimitro@delphix.com>
In a virtual machine, VMCI is exposed as a regular PCI device. The primary
communication mechanisms supported are a point-to-point bidirectional
transport based on a pair of memory-mapped queues, and asynchronous
notifications in the form of datagrams and doorbells. These features are
available to kernel level components such as vSockets through the VMCI
kernel API. In addition to this, the VMCI kernel API provides support for
receiving events related to the state of the VMCI communication channels,
and the virtual machine itself.
Submitted by: Vishnu Dasa <vdasa@vmware.com>
Reviewed by: bcr, imp
Obtained from: VMware
Differential Revision: https://reviews.freebsd.org/D14289
DTB Overlays are useful to change/add nodes to a dtb without the need to
modify it.
Add support for building dtbo during buildkernel.
The goal of DTBO present in the FreeBSD source tree is to fill a gap in
time when we submit changes upstream (Linux). Instead of waiting 2 to 4 months
we can add a DTBO in tree in the meantime.
This is not for adding DTBO for capes/hat/addon boards, those will be
better to put in a ports.
This is also not for enabling a i2c/spi/pwm controller on certain pins,
each user have a different use case for those (which pins to use etc ...)
and we cannot have all possible configuration.
Add a dtbo for sun8i-h3-sid which add the SID node missing in upstream dts.
Reviewed by: kevans
Differential Revision: https://reviews.freebsd.org/D14782
controlled by the TCP_BLACKBOX option.
Enable this as part of amd64 GENERIC. For now, leave it disabled on
other platforms.
Sponsored by: Netflix, Inc.
Since the FW can be shared between PCI functions it is common that
more than one health poll will detected a failure, this can lead to
multiple resets.
The solution is to use a FW locking mechanism using semaphore space to
provide a way to synchronize between functions. The FW semaphore is
acquired via config cycle access. First the VSEC gateway must be
acquired, then the semaphore can be locked by writing a value to it
and confirmed it's locked by reading the same value back. The process
in the same to free the semaphore, except the value written should be
zero.
Submitted by: slavash@
MFC after: 1 week
Sponsored by: Mellanox Technologies
In pursuit of improving performance on multi-core systems, we should
implements fanned out counters and use them to improve the performance of
some of the arc statistics. These stats are updated extremely frequently,
and can consume a significant amount of CPU time.
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Author: Paul Dagnelie <pcd@delphix.com>
summits at BSDCan and BSDCam in 2017.
The TCP Blackbox Recorder allows you to capture events on a TCP connection
in a ring buffer. It stores metadata with the event. It optionally stores
the TCP header associated with an event (if the event is associated with a
packet) and also optionally stores information on the sockets.
It supports setting a log ID on a TCP connection and using this to correlate
multiple connections that share a common log ID.
You can log connections in different modes. If you are doing a coordinated
test with a particular connection, you may tell the system to put it in
mode 4 (continuous dump). Or, if you just want to monitor for errors, you
can put it in mode 1 (ring buffer) and dump all the ring buffers associated
with the connection ID when we receive an error signal for that connection
ID. You can set a default mode that will be applied to a particular ratio
of incoming connections. You can also manually set a mode using a socket
option.
This commit includes only basic probes. rrs@ has added quite an abundance
of probes in his TCP development work. He plans to commit those soon.
There are user-space programs which we plan to commit as ports. These read
the data from the log device and output pcapng files, and then let you
analyze the data (and metadata) in the pcapng files.
Reviewed by: gnn (previous version)
Obtained from: Netflix, Inc.
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D11085
The upstream repository is on github BLAKE2/libb2. Files landed in
sys/contrib/libb2 are the unmodified upstream files, except for one
difference: secure_zero_memory's contents have been replaced with
explicit_bzero() only because the previous implementation broke powerpc
link. Preferential use of explicit_bzero() is in progress upstream, so
it is anticipated we will be able to drop this diff in the future.
sys/crypto/blake2 contains the source files needed to port libb2 to our
build system, a wrapped (limited) variant of the algorithm to match the API
of our auth_transform softcrypto abstraction, incorporation into the Open
Crypto Framework (OCF) cryptosoft(4) driver, as well as an x86 SSE/AVX
accelerated OCF driver, blake2(4).
Optimized variants of blake2 are compiled for a number of x86 machines
(anything from SSE2 to AVX + XOP). On those machines, FPU context will need
to be explicitly saved before using blake2(4)-provided algorithms directly.
Use via cryptodev / OCF saves FPU state automatically, and use via the
auth_transform softcrypto abstraction does not use FPU.
The intent of the OCF driver is mostly to enable testing in userspace via
/dev/crypto. ATF tests are added with published KAT test vectors to
validate correctness.
Reviewed by: jhb, markj
Obtained from: github BLAKE2/libb2
Differential Revision: https://reviews.freebsd.org/D14662
The general idea here is to provide userspace programs with well-defined
sources of entropy, in a fashion that doesn't require opening a new file
descriptor (ulimits) or accessing paths (/dev/urandom may be restricted
by chroot or capsicum).
getrandom(2) is the more general API, and comes from the Linux world.
Since our urandom and random devices are identical, the GRND_RANDOM flag
is ignored.
getentropy(3) is added as a compatibility shim for the OpenBSD API.
truss(1) support is included.
Tests for both system calls are provided. Coverage is believed to be at
least as comprehensive as LTP getrandom(2) test coverage. Additionally,
instructions for running the LTP tests directly against FreeBSD are provided
in the "Test Plan" section of the Differential revision linked below. (They
pass, of course.)
PR: 194204
Reported by: David CARLIER <david.carlier AT hardenedbsd.org>
Discussed with: cperciva, delphij, jhb, markj
Relnotes: maybe
Differential Revision: https://reviews.freebsd.org/D14500
assym is only to be included by other .s files, and should never
actually be assembled by itself.
Reviewed by: imp, bdrewery (earlier)
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D14180
Some parts of MI modules will soon depend on whether EFI is available
or not. Add EFI to the list of kernel options so we can use it in
the modules build.
Three copies of the linuxulator linux_sysvec.c contained identical
BSD to Linux errno translation tables, and future work to support other
architectures will also use the same table. Move the table to a common
file to be used by all. Make it 'const int' to place it in .rodata.
(Some existing Linux architectures use MD errno values, but x86 and Arm
share the generic set.)
This change should introduce no functional change; a followup will add
missing errno values.
MFC after: 3 weeks
Sponsored by: Turing Robotic Industries Inc.
Differential Revision: https://reviews.freebsd.org/D14665
Two copies of chacha20 were imported into the tree on Apr 15 2017 (r316982)
and Apr 16 2017 (r317015). Only the latter is actually used by anything, so
just go ahead and garbage collect the unused version while it's still only
in CURRENT.
I'm not making any judgement on which implementation is better. If I pulled
the wrong one, feel free to swap the existing implementation out and replace
it with the other code (conforming to the API that actually gets used in
randomdev, of course). We only need one generic implementation.
Sponsored by: Dell EMC Isilon
being marked "standard", which is less confusing than having it conditional
on AIM CPUs here, and then picked up through options FDT from conf/files
on Book-E.
Request by: jhibbits
kern.cam.{,a,n}da.X.invalidate=1 forces *daX to detach by calling
cam_periph_invalidate on the underlying periph. This is for testing
purposes only. Include only with options CAM_TEST_FAILURE and rename
the former [AN]DA_TEST_FAILURE, and fix nda to compile with it set.
We're using it at work to harden geom and the buffer cache to be
resilient in the face of drive failure. Today, it far too often
results in a panic. While much work was done on SIM initiated removal
for the USB thumnb drive removal work, little has been done for periph
initiated removal. This simulates what *daerror() does for some errors
nicely: we get the same panics with it that we do with failing drives.
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D14581
platform that can run without a device tree (PS3) still uses the OF_*()
functions to check if one exists and OF_* is used unconditionally in
core parts of the system like powerpc/machdep.c. Reflect this reality
in files.powerpc, for example by changing occurrences of aim | fdt to
standard.
ConnectX-4/5 devices in mlx5core.
The dump is obtained by reading a predefined register map from the
non-destructive crspace, accessible by the vendor-specific PCIe
capability (VSC). The dump is stored in preallocated kernel memory and
managed by the mlx5tool(8), which communicates with the driver using a
character device node.
The utility allows to store the dump in format
<address> <value>
into a file, to reset the dump content, and to manually initiate the
dump.
A call to mlx5_fwdump() should be added at the places where a dump
must be fetched automatically. The most likely place is right before a
firmware reset request.
Submitted by: kib@
MFC after: 1 week
Sponsored by: Mellanox Technologies
Add the ability to access the vendor specific space gateway in order
to support reading and writing data into the different configuration
domains.
Submitted by: Matthew Finlay <matt@mellanox.com>
MFC after: 1 week
Sponsored by: Mellanox Technologies
ECN configuration and statistics is available through a set of sysctl(8)
nodes under sys.class.infiniband.mlx5_X.cong . The ECN configuration
nodes can also be used as loader tunables.
MFC after: 1 week
Sponsored by: Mellanox Technologies
bus provide it with its needed memory resources.
This allows us to use PCIe on the ThunderX2 and, with a previous version
of the patch, on the SoftIron 3000 with ACPI.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Sponsored by: DARPA, AFRL
Sponsored by: Cavium (Hardware)
Differential Revision: https://reviews.freebsd.org/D8767
correctly for the data contained on each memory page.
There are several components to this change:
* Add a variable to indicate the start of the R/W portion of the
initial memory.
* Stop detecting NX bit support for each AP. Instead, use the value
from the BSP and, if supported, activate the feature on the other
APs just before loading the correct page table. (Functionally, we
already assume that the BSP and all APs had the same support or
lack of support for the NX bit.)
* Set the RW and NX bits correctly for the kernel text, data, and
BSS (subject to some caveats below).
* Ensure DDB can write to memory when necessary (such as to set a
breakpoint).
* Ensure GDB can write to memory when necessary (such as to set a
breakpoint). For this purpose, add new MD functions gdb_begin_write()
and gdb_end_write() which the GDB support code can call before and
after writing to memory.
This change is not comprehensive:
* It doesn't do anything to protect modules.
* It doesn't do anything for kernel memory allocated after the kernel
starts running.
* In order to avoid excessive memory inefficiency, it may let multiple
types of data share a 2M page, and assigns the most permissions
needed for data on that page.
Reviewed by: jhb, kib
Discussed with: emaste
MFC after: 2 weeks
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D14282
separate 2M pages. The binutils default for max-page-size and
common-page-size used to produce this result. By setting these
values, we can nudge lld to also separate these sections into separate
2M pages.
Reviewed by: jhb, kib
Discussed with: emaste
Sponsored by: Netflix
Differential Revision: D14282
imcsmb(4) provides smbus(4) support for the SMBus controller functionality
in the integrated Memory Controllers (iMCs) embedded in Intel Sandybridge-
Xeon, Ivybridge-Xeon, Haswell-Xeon, and Broadwell-Xeon CPUs. Each CPU
implements one or more iMCs, depending on the number of cores; each iMC
implements two SMBus controllers (iMC-SMBs).
*** IMPORTANT NOTE ***
Because motherboard firmware or the BMC might try to use the iMC-SMBs for
monitoring DIMM temperatures and/or managing an NVDIMM, the driver might
need to temporarily disable those functions, or take a hardware interlock,
before using the iMC-SMBs. Details on how to do this may vary from board to
board, and the procedure may be proprietary. It is strongly suggested that
anyone wishing to use this driver contact their motherboard vendor, and
modify the driver as described in the manual page and in the driver itself.
(For what it's worth, the driver as-is has been tested on various SuperMicro
motherboards.)
Reviewed by: avg, jhb
MFC after: 1 week
Relnotes: yes
Sponsored by: Panasas
Differential Revision: https://reviews.freebsd.org/D14447
Discussed with: avg, ian, jhb
Tested by: allanjude (previous version), Panasas
Add I2C OPAL driver and a set of dummy-ones to allow
all I2C things on Power8 to attach.
TODO: better async token management
Submitted by: Wojciech Macek <wma@semihalf.com>
Obtained from: Semihalf
Sponsored by: IBM, QCM Technologies
Retpoline is a compiler-based mitigation for CVE-2017-5715, also known
as Spectre V2, that protects against speculative execution branch target
injection attacks.
In this commit it is disabled by default, but will be changed in a
followup commit.
Reviewed by: bdrewery (previous version)
MFC after: 3 days
Security: CVE-2017-5715
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D14242
* rk_cru is a cru driver that needs to be subclassed by
the real CRU driver
* rk_clk_pll handle the pll type clock on RockChip SoC, it's only read
only for now.
* rk_clk_composite handle the different composite clock types (with gate,
with mux etc ...)
* rk_clk_gate handle the RockChip gates
* rk_clk_mux handle the RockChip muxes (unused for now)
* Only clocks for supported devices are supported for now, the rest will be
added when driver support comes
* The assigned-clock* property are not handled for now so we rely a lot on the
bootloader to setup some initial values for some clocks.
[RFC7413]. It also includes a pre-shared key mode of operation in
which the server requires the client to be in possession of a shared
secret in order to successfully open TFO connections with that server.
The names of some existing fastopen sysctls have changed (e.g.,
net.inet.tcp.fastopen.enabled -> net.inet.tcp.fastopen.server_enable).
Reviewed by: tuexen
MFC after: 1 month
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D14047
use it to regulate page daemon output.
This provides much smoother and more responsive page daemon output, anticipating
demand and avoiding pageout stalls by increasing the number of pages to match
the workload. This is a reimplementation of work done by myself and mlaier at
Isilon.
Reviewed by: bsdimp
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D14402
A super-set of the functionality of jedec_ts(4). jedec_dimm(4) reports asset
information (Part Number, Serial Number) encoded in the "Serial Presence
Detect" (SPD) data on JEDEC DDR3 and DDR4 DIMMs. It also calculates and
reports the memory capacity of the DIMM, in megabytes. If the DIMM includes
a "Thermal Sensor On DIMM" (TSOD), the temperature is also reported.
Reviewed by: cem
MFC after: 1 week
Relnotes: yes
Sponsored by: Panasas
Differential Revision: https://reviews.freebsd.org/D14392
Discussed with: avg, cem
Tested by: avg, cem (previous version, no semantic changes)
Add chvgpio(4) driver for Intel Z8xxx SoC family. This product
was formerly known as Cherry Trail but Linux and OpenBSD drivers
refer to it as Cherry View. This driver is derived from OpenBSD
one so the name is kept for alignment with another BSD system.
Submitted by: Tom Jones <tj@enoti.me>
Reviewed by: gonzo, wblock(man page)
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D13086
Remove bitfields from defined structures as they are not portable.
Instead use shift and mask macros in the driver and nvmecontrol application.
NVMe is now working on powerpc64 host.
Submitted by: Michal Stanek <mst@semihalf.com>
Obtained from: Semihalf
Reviewed by: imp, wma
Sponsored by: IBM, QCM Technologies
Differential revision: https://reviews.freebsd.org/D13916
9079 race condition in starting and ending condesing thread for indirect vdevs
illumos/illumos-gate@667ec66f1b
The timeline of the race condition is the following:
[1] Thread A is about to finish condesing the first vdev in spa_condense_indirect_thread(),
so it calls the spa_condense_indirect_complete_sync() sync task which sets the
spa_condensing_indirect field to NULL. Waiting for the sync task to finish, thread A
sleeps until the txg is done. When this happens, thread A will acquire spa_async_lock
and set spa_condense_thread to NULL.
[2] While thread A waits for the txg to finish, thread B which is running spa_sync() checks
whether it should condense the second vdev in vdev_indirect_should_condense() by checking
the spa_condensing_indirect field which was set to NULL by spa_condense_indirect_thread()
from thread A. So it goes on and tries to spawn a new condensing thread in
spa_condense_indirect_start_sync() and the aforementioned assertions fails because thread A
has not set spa_condense_thread to NULL (which is basically the last thing it does before
returning).
The main issue here is that we rely on both spa_condensing_indirect and spa_condense_thread to
signify whether a condensing thread is running. Ideally we would only use one throughout the
codebase. In addition, for managing spa_condense_thread we currently use spa_async_lock which
basically tights condensing to scrubing when it comes to pausing and resuming those actions
during spa export.
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Reviewed by: Pavel Zakharov <pavel.zakharov@delphix.com>
Approved by: Hans Rosenfeld <rosenfeld@grumpf.hope-2000.org>
Author: Serapheim Dimitropoulos <serapheim@delphix.com>
illumos/illumos-gate@5cabbc6b49https://www.illumos.org/issues/7614:
This project allows top-level vdevs to be removed from the storage pool with
“zpool remove”, reducing the total amount of storage in the pool. This
operation copies all allocated regions of the device to be removed onto other
devices, recording the mapping from old to new location. After the removal is
complete, read and free operations to the removed (now “indirect”) vdev must
be remapped and performed at the new location on disk. The indirect mapping
table is kept in memory whenever the pool is loaded, so there is minimal
performance overhead when doing operations on the indirect vdev.
The size of the in-memory mapping table will be reduced when its entries
become “obsolete” because they are no longer used by any block pointers in
the pool. An entry becomes obsolete when all the blocks that use it are
freed. An entry can also become obsolete when all the snapshots that
reference it are deleted, and the block pointers that reference it have been
“remapped” in all filesystems/zvols (and clones). Whenever an indirect block
is written, all the block pointers in it will be “remapped” to their new
(concrete) locations if possible. This process can be accelerated by using
the “zfs remap” command to proactively rewrite all indirect blocks that
reference indirect (removed) vdevs.
Note that when a device is removed, we do not verify the checksum of the data
that is copied. This makes the process much faster, but if it were used on
redundant vdevs (i.e. mirror or raidz vdevs), it would be possible to copy
the wrong data, when we have the correct data on e.g. the other side of the
mirror. Therefore, mirror and raidz devices can not be removed.
Reviewed by: Alex Reece <alex@delphix.com>
Reviewed by: George Wilson <george.wilson@delphix.com>
Reviewed by: John Kennedy <john.kennedy@delphix.com>
Reviewed by: Prakash Surya <prakash.surya@delphix.com>
Reviewed by: Matthew Ahrens <mahrens@delphix.com>
Reviewed by: Richard Laager <rlaager@wiktel.com>
Reviewed by: Tim Chase <tim@chase2k.com>
Approved by: Garrett D'Amore <garrett@damore.org>
Author: Prashanth Sreenivasa <pks@delphix.com>
When processor enters power-save state it releases resources shared with other
cpu threads which makes other cores working much faster.
This patch also implements saving and restoring registers that might get
corrupted in power-save state.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Reviewed by: jhibbits, nwhitehorn, wma
Sponsored by: IBM, QCM Technologies
Differential revision: https://reviews.freebsd.org/D14330
EXPORT_SYMS can be set to YES, NO, a list of symbols to export from a
module, or to a filename containing such a list. For the case that it
is set to a symbol list, replace spaces in the list with newlines, so
the created file is in the format expected by kmod_syms.awk.
Reviewed by: imp, jhb
MFC after: 1 month
Sponsored by: Turing Robotic Industries Inc.
Differential Revision: https://reviews.freebsd.org/D14284
This works similarly to the existing gzip compression support, but
zstd is typically faster and gives better compression ratios.
Support for this functionality must be configured by adding ZSTDIO to
one's kernel configuration file. dumpon(8)'s new -Z option is used to
configure zstd compression for kernel dumps. savecore(8) now recognizes
and saves zstd-compressed kernel dumps with a .zst extension.
Submitted by: cem (original version)
Relnotes: yes
Sponsored by: Dell EMC Isilon
Differential Revision: https://reviews.freebsd.org/D13101,
https://reviews.freebsd.org/D13633
This came about when r328489 made ports modules builds no longer use the
in-tree share/mk files, but didn't cleanup MAKEOBJDIR from the
environment.
This fixes "Variable OBJTOP is recursive".
Sponsored by: Dell EMC
compilation under FreeBSD. The mthca driver was temporarily removed as
part of the Linux 4.9 RoCE/infinband upgrade.
Top commit in Linux source tree:
69973b830859bc6529a7a0468ba0d80ee5117826
Sponsored by: Mellanox Technologies
o added struct ipfw_dyn_info that keeps all needed for ipfw_chk and
for dynamic states implementation information;
o added DYN_LOOKUP_NEEDED() macro that can be used to determine the
need of new lookup of dynamic states;
o ipfw_dyn_rule now becomes obsolete. Currently it used to pass
information from kernel to userland only.
o IPv4 and IPv6 states now described by different structures
dyn_ipv4_state and dyn_ipv6_state;
o IPv6 scope zones support is added;
o ipfw(4) now depends from Concurrency Kit;
o states are linked with "entry" field using CK_SLIST. This allows
lockless lookup and protected by mutex modifications.
o the "expired" SLIST field is used for states expiring.
o struct dyn_data is used to keep generic information for both IPv4
and IPv6;
o struct dyn_parent is used to keep O_LIMIT_PARENT information;
o IPv4 and IPv6 states are stored in different hash tables;
o O_LIMIT_PARENT states now are kept separately from O_LIMIT and
O_KEEP_STATE states;
o per-cpu dyn_hp pointers are used to implement hazard pointers and they
prevent freeing states that are locklessly used by lookup threads;
o mutexes to protect modification of lists in hash tables now kept in
separate arrays. 65535 limit to maximum number of hash buckets now
removed.
o Separate lookup and install functions added for IPv4 and IPv6 states
and for parent states.
o By default now is used Jenkinks hash function.
Obtained from: Yandex LLC
MFC after: 42 days
Sponsored by: Yandex LLC
Differential Revision: https://reviews.freebsd.org/D12685
- Remove the shim interface that allowed bwn(4) to use either siba_bwn or
bhnd(4), replacing all siba_bwn calls with their bhnd(4) bus equivalents.
- Drop the legay, now-unused siba_bwn bus driver.
- Clean up bhnd(4) board flag defines referenced by bwn(4).
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D13518
superblock, and the kernel will fail to link when UFS is not built
in. This commit makes it depend on a small portion of FFS bits and
thereby fixes build for this situation.
This is intended as an interim bandaid, and the actual superblock
reading code should probably be made independent of UFS, so we do
not need to depend on it (see kib@'s comment in the review for
details), and we will revisit this once the superblock check hashes
are all in place.
Differential Revision: https://reviews.freebsd.org/D14092
net80211/ieee80211_ageq.c was present twice in sys/conf/files so leave the
correctly sorted one. dev/wpi/if_wpi.c was present in sys/conf/files as well
as sys/conf/files.amd64 and sys/conf/files.i386 so prefer the sys/conf/files
entry.
Reviewed by: allanjude, rstone
gone_in(majar, msg); If we're running in FreeBSD major, tell
the user this code may be deleted soon.
If we're running in FreeBSD major - 1,
the the user is deprecated and will
be gone in major.
Otherwise say nothing.
gone_in_dev(dev, major, msg) Just like gone_in, except use device_printf.
New tunable / sysctl debug.oboslete_panic: 0 - don't panic,
1 - panic in major or newer , 2 - panic in major - 1 or newer
default: 0
if NO_OBSOLETE_CODE is defined, then both of these turn into compile
time errors when building for major. Add options NO_OBSOLETE_CODE to
kernel build system.
This lets us tag code that's going away so users know it will be gone,
as well as automatically manage things.
Differential Review: https://reviews.freebsd.org/D13818
Previously, MAKESYSPATH as well as '-m' directives in MAKEFLAGS would cause
any port rebuilt during the PORTS_MODULES stage to consume system makefiles
from $(SRCROOT)/share/mk instead of those installed under /usr/share/mk.
For kernel modules that need to build against an updated src tree this
makes sense; less so for <bsd.port.mk> or any userspace library or utility
the port may also happen to install.
Before 11.0, this probably didn't matter much in practice. But the addition
of src.libnames.mk under $(SRCROOT)/share/mk in 11.0 breaks any consumer of
bsd.prog.mk and DPADD/LDADD during PORTS_MODULES.
Address the build breakage by removing MAKESYSPATH and any occurrence of
'-m' from MAKEFLAGS in the environment created for the port build.
Instead set SYSDIR so that any kmod built by the port will still consume
conf/kmod.mk from the updated src tree, assuming it uses <bsd.kmod.mk>
Reviewed by: bdrewery
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D13053
leaks. We assume each source can be taken / dropped only once and
don't recurse. These are only enabled via DA_TRACK_REFS or
INVARIANTS. There appreas to be a reference leak under extreme load,
and these should help us colaberatively work it out. It also documents
better the reference / holding protocol better.
Reviewed by: ken@, scottl@
Sponsored by: Netflix
Differential Revision: https://reviews.freebsd.org/D14040
Similarly as other extres pseudo-drivers, implement phy by using kobj model.
This detaches it from provider device, so single device driver can export
multiple different phys. Additionally, this allows phy to be subclassed to
more specialized drivers, like is USB OTG phy, or PCIe phy with hot-plug
capability.
Tested by: manu (previous version, on Allwinner board)
MFC after: 1 month
Both flags do the same thing but -n is more widely supported.
Reviewed By: jhb, emaste
Approved By: jhb (mentor)
Differential Revision: https://reviews.freebsd.org/D13936
Make XICS to be OPAL-aware.
Created by: Nathan Whitehorn <nwhitehorn@freebsd.org>
Submitted by: Wojciech Macek <wma@semihalf.com>
Sponsored by: FreeBSD Foundation
Some PowerQUICC and QorIQ platforms have a L2 cache managed via the
memory-mapped configuration registers, and appear as a node in the device
tree. This adds basic support to enable the cache.
userspace to control NUMA policy administratively and programmatically.
Implement domainset based iterators in the page layer.
Remove the now legacy numa_* syscalls.
Cleanup some header polution created by having seq.h in proc.h.
Reviewed by: markj, kib
Discussed with: alc
Tested by: pho
Sponsored by: Netflix, Dell/EMC Isilon
Differential Revision: https://reviews.freebsd.org/D13403
Provide initial support for PCIe host controller as
well as for IOMMU mapping. This commit allows proper
bus enumeration, but does not guarantee DMA operations
are working.
Created by: Nathan Whitehorn <nwhitehorn@freebsd.org>
Submitted by: Wojciech Macek <wma@semihalf.com>
Sponsored by: FreeBSD Foundation
For each we need to walk the MADT to find which we have, then add the
driver as needed. As each may have a child they will each walk the same
table to find these details.
Reviewed by: mmel
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8720
This adds a new acpi_bus interface with a map_intr method. This is similar
to the Open Firmware map_intr method and allows us to create the needed
mapping from ACPI space to INTRNG space.
Obtained from: ABT Systems Ltd
Sponsored by: The FreeBSD Foundation
Differential Revision: https://reviews.freebsd.org/D8617
OPAL is a dedicated firmware acting as a hypervisor.
Add generic functions to provide all access.
Created by: Nathan Whitehorn <nw@freebsd.org>
Submitted by: Wojciech Macek <wma@freebsd.org>
Iwasaki-san's copyright over. Remove FIXME code that couldn't possibly
work. Call tc_settime() with our estimate of the delta we've been
alseep (the one we print) to adjust the time. Not sure what to do
about callouts, so keep the small #ifdef in place there.
Differential Revision: https://reviews.freebsd.org/D13823
Add an implementation of the intrinsics invoked by __builtin_ctz{,ll} and
__builtin_clz{,ll}, and include this compilation unit on platforms that lack
assembly intrinsics for those builtins (MIPS and RISC-V).
Future cleanup work might involve bringing these into a mini libcompiler-rt
for the standalone kernel environment. Or cleaning up the approach upstream
takes for builtins in standalone environments (or just FreeBSD). For now,
at least this builds, and doesn't require modifying the vendor code.
Reported by: jeff, markj, mizhka
Reviewed by: jhb (earlier version), rpokala (comment text earlier version)
Sponsored by: Dell EMC Isilon
Disable Zstd experimental support for __BMI__ intrinsics, when built with
-march=foo supporting such intrinsics, to avoid attempting to include
immintrin.h. If a later Zstd marks the support non-experimental, we may want
to revisit this approach.
Submitted by: jkim
Reported by: jkim, "Oliver Hartmann" <ohartmann AT walstatt.org>
a mask and value to compare with the Main ID Register. If these match then a
function is called to handle the installation of the erratum workaround.
No errata are currently handled, however this will change soon in a future
commit.
MFC after: 1 week
Sponsored by: DARPA, AFRL
By disabling the -Winline warning. Fixes the powerpc and sparc64 build
after r327706.
Note: MIPS and RISCV builds still broken due to absense of __ctzdi2 (aka
__builtin_ctzll) in their libgcc or libcompiler-rt libraries.
Reported by: markj
Sponsored by: Dell EMC Isilon
We currently use a set of subroutines in kern_gzio.c to perform
compression of user and kernel core dumps. In the interest of adding
support for other compression algorithms (zstd) in this role without
complicating the API consumers, add a simple compressor API which can be
used to select an algorithm.
Also change the (non-default) GZIO kernel option to not enable
compressed user cores by default. It's not clear that such a default
would be desirable with support for multiple algorithms implemented,
and it's inconsistent in that it isn't applied to kernel dumps.
Reviewed by: cem
Differential Revision: https://reviews.freebsd.org/D13632
Mock userspace headers and include mocked headers first in compilation
command to inject kernel headers and override e.g., malloc(3) with
malloc(9).
Submitted by: allanjude
Reviewed by: imp (earlier version), bapt (earlier version)
Differential Revision: https://reviews.freebsd.org/D10407
The emac bindings that are landing in Linux 4.15 specify a syscon property
on the emac node that point to /soc/syscon. Use this property if it's
specified, but maintain backwards compatibility with the old method.
The older method is still used for boards that we get .dtb from u-boot, such
as pine64, that did not yet have stable emac bindings.
Tested on: Banana Pi-M3 (a83t)
Tested on: Pine64 (a64)
Reviewed by: manu
Differential Revision: https://reviews.freebsd.org/D13296
Enable the hardclock-based watchdog previously conditional on the
SW_WATCHDOG option whenever hardware watchdogs are not found, and
watchdogd attempts to enable the watchdog. The SW_WATCHDOG option
still causes the sofware watchdog to be enabled even if there is a
hardware watchdog. This does not change the other software-based
watchdog enabled by the --softtimeout option to watchdogd.
Note that the code to reprime the watchdog during kernel core dumps is
no longer conditional on SW_WATCHDOG. I think this was previously a bug.
Reviewed by: imp alfred bjk
MFC after: 1 week
Relnotes: yes
Differential Revision: https://reviews.freebsd.org/D13713
These are intended for debugging purposes and should not be added to
"generic" kernel configurations since they result in a nontrivial amount
of memory being set aside for this purpose, can break if kernel modules are
unloaded, and can potentially leak a dangerous amount of information about
timestamps used as a source of kernel entropy.
The ep(4) driver is the only consumer of the two functions from
elink.c. I removed the standalone module as well, and most likely,
the module metadata is not needed anywhere, but this is for later
cleanup.
Discussed with: imp, jhb
Sponsored by: The FreeBSD Foundation
The i386 FPU (AKA npx) code does not depend on ISA devices at all,
after the support for IRQ13 FPU exceptions was removed. Put the file
into the expected place in the kernel source tree.
Discussed with: jhb
Sponsored by: The FreeBSD Foundation
files that can use the default value.
It used to be required that the low-order bits of KERNVIRTADDR matched
the low-order bits of the physical load address for all arm platforms.
That hasn't been a requirement for armv6 platforms since FreeBSD 10.
There is no longer any relationship between load addr and KERNVIRTADDR
except that both must be aligned to a 2 MiB boundary.
This change makes the default KERNVIRTADDR value 0xc0000000, and removes the
options from all the platforms that can use the default value. The default
is now defined in vmparam.h, and that file is now included in a few new
places that reference KERNVIRTADDR, since it may not come in via the
forced-include of opt_global.h on the compile command line.
is used as the bootloader on a number of PPC64 platforms. This involves the
following pieces:
- Making the first instruction a valid kernel entry point, since kexec
ignores the ELF entry value. This requires a separate section and linker
magic to prevent the linker from filling the beginning of the section
with stubs.
- Adding an entry point at 0x60 past the first instruction for systems
lacking firmware CPU shutdown support (notably PS3).
- Linker script changes to support the above.
MFC after: 1 month
draft of a never-finalized standard (CHRP) and is irrelevant in practice
on FreeBSD since we load the kernel with loader(8) on Open Firmware
platforms anyway. Moreover, loader(8), which is directly loaded by Open
Firmware, has never had an equivalent note.
MFC after: 2 weeks
kernel VA mapping in the temporary page tables set up by locore-v6.S.
The number used to be hard-coded to 64MB, which is still the default if
the kernel option is not specified. However, 64MB is insufficient for
using a large mdroot filesystem. The hard-coded number can't be safely
increased because too large a number may run into memory-mapped IO space
on some SoCs that must not be mapped as ordinary memory.
