it doesn't block packets whose destination address has been translated to
the loopback net by ipnat.
Add warning comments about the ip_checkinterface feature.
aiocb's allocated by zalloc(). In other words, zfree() was never
called. Now, we call zfree(). Why eliminate this micro-
optimization? At some later point, when we multithread the AIO
system, we would need a mutex to synchronize access to aio_freejobs,
making its use nearly indistinguishable in cost from zalloc() and
zfree().
Remove unnecessary fhold() and fdrop() calls from aio_qphysio(),
undo'ing a part of revision 1.86. The reference count on the file
structure is already incremented by _aio_aqueue() before it calls
aio_qphysio(). (Update the comments to document this fact.)
Remove unnecessary casts from _aio_aqueue(), aio_read(), aio_write()
and aio_waitcomplete().
Remove an unnecessary "return;" from aio_process().
Add "static" in various places.
However, if the RTF_DELCLONE and RTF_WASCLONED condition passes, but the ref
count is > 1, we won't decrement the count at all. This could lead to
route entries never being deleted.
Here, we call rtfree() not only if the initial two conditions fail, but
also if the ref count is > 1 (and we therefore don't immediately delete
the route, but let rtfree() handle it).
This is an urgent MFC candidate. Thanks go to Mike Silbersack for the
fix, once again. :-)
Submitted by: Mike Silbersack <silby@silby.com>
addressed to the interface on the other side of the box follow their
historical path.
Explicitly block packets sent to the loopback network sent from the outside,
which is consistent with the behavior of the forwarding path between
interfaces as implemented in in_canforward().
Always check the arrival interface when matching the packet destination
against the interface broadcast addresses. This bug allowed TCP
connections to be made to the broadcast address of an interface on the
far side of the system because the M_BCAST flag was not set because the
packet was unicast to the interface on the near side. This was broken
when the directed broadcast code was removed from revision 1.32. If
the directed broadcast code was stil present, the destination would not
have been recognized as local until the packet was forwarded to the output
interface and ether_output() looped a copy back to ip_input() with
M_BCAST set and the receive interface set to the output interface.
Optimize the order of the tests.
Reviewed by: jlemon
related code from aio_read() and aio_write(). This field was
intended, but never used, to allow a mythical user-level library to
make an aio_read() or aio_write() behave like an ordinary read() or
write(), i.e., a blocking I/O operation.
user space. It has already been copied in and mp->mnt_stat.f_mntonname has
already been initialised by the caller.
This fixes a panic on the alpha caused by the fact that the variable
'size' wasn't initialised because the call to copyinstr() bailed out with
an EFAULT error.
bolted to a ne-2000 chip. This is necessary for the NetGear FA-410TX
and other cards.
This also requires you add mii to your kernel if you have an ed driver
configured.
This code will result in a couple of timeout messages for ed on the
impacted cards. Additional work will be needed, but this does work
right now, and many people need these cards.
Submitted by: Ian Dowse <iedowse@maths.tcd.ie>
`infrastructure' built with INVARIANT_SUPPORT for kern_mutex.c essentially
involves _mtx_assert(), which makes use of constants that were defined
under #ifdef INVARIANTS here.
This is a pretty invasive change, but there are three good
reasons to do this:
1. We'll never have > 16 bits of handle.
2. We can (eventually) enable the RIO (Reduced Interrupt Operation)
bits which return multiple completing 16 bit handles in mailbox
registers.
3. The !)$*)$*~)@$*~)$* Qlogic target mode for parallel SCSI spec
changed such that at_reserved (which was 32 bits) was split into
two pieces- and one of which was a 16 bit handle id that functions
like the at_rxid for Fibre Channel (a tag for the f/w to correlate
CTIOs with a particular command). Since we had to muck with that
and this changed the whole handler architecture, we might as well...
Propagate new at_handle on through int ct_fwhandle. Follow
implications of changing to 16 bit handles.
These above changes at least get Qlogic 1040 cards working in target
mode again. 1080/12160 cards don't work yet.
In isp.c:
Prepare for doing all loop management in outer layers.
with egcs-1.1.1. bus_space_write_multi_2() had an extra operation that
should have been removed.
Remove it.
This fixes the panic when bus_space_write_multi_2() is used.
Obtained from: jake
- Add a KASSERT() to ensure an ithread has a backing kernel thread when we
schedule it.
- Don't attempt to preemptively switch to an ithread if p_stat of curproc
is not SRUN.
newbus in revision 1.19. As a result, lnc was, I believe, broken
for all PCI cards. The softc fields `lnc_btag' and `lnc_bhandle'
were not initialised, `rap', `rdp' and `bdp' were initialised to
the wrong values, and the size of the DMA ring memory was calculated
incorrectly.
Paul Richards has further cleanups in the pipeline, but this at
least is enough to make the driver usable with VMware.
Approved by: paul
is to return EINPROGRESS, EALREADY, (so_error ONCE), EISCONN. Certain
linux applications rely on the so_error (normally 0) being returned in
order to operate properly.
Tested by: Thomas Moestl <tmoestl@gmx.net>
An initial tidyup of the mount() syscall and VFS mount code.
This code replaces the earlier work done by jlemon in an attempt to
make linux_mount() work.
* the guts of the mount work has been moved into vfs_mount().
* move `type', `path' and `flags' from being userland variables into being
kernel variables in vfs_mount(). `data' remains a pointer into
userspace.
* Attempt to verify the `type' and `path' strings passed to vfs_mount()
aren't too long.
* rework mount() and linux_mount() to take the userland parameters
(besides data, as mentioned) and pass kernel variables to vfs_mount().
(linux_mount() already did this, I've just tidied it up a little more.)
* remove the copyin*() stuff for `path'. `data' still requires copyin*()
since its a pointer into userland.
* set `mount->mnt_statf_mntonname' in vfs_mount() rather than in each
filesystem. This variable is generally initialised with `path', and
each filesystem can override it if they want to.
* NOTE: f_mntonname is intiailised with "/" in the case of a root mount.
