Prober support for the VIA 82C686, I finally got the right datasheet.
Get rid of atapi_wait, merge it into ata_wait.
Avoid a couple of races by using asleep instead of tsleep.
Always use 16bit transfers on ISA systems.
Clear up the atapi_read/write functions.
of the Broadcom BCM5201 PHY on the LinkSys USB100TX adapter so that the
link LED correctly (lights up amber for 10mbps link, green for 100mbps
link).
Note that the sticker on the bottom of the adapter says amber for 10
and green for 100, but the appendix in the manual that comes with
the adapter says green for 10 and amber for 100. Given that there doesn't
seem to be any way to make the hardware produce the latter combination,
I think it's safe to say the sticker is right and the manual is wrong.
I'm just shocked, shocked I tell you.
- Split terminal emulation code from the main part of the driver so
that we can have alternative terminal emulator modules if we like in
the future. (We are not quite there yet, though.)
- Put sysmouse related code in a separate file, thus, simplifying the
main part of the driver.
As some files are added to the source tree, you need to run config(8)
before you compile a new kernel next time.
You shouldn't see any functional change by this commit; this is only
internal code reorganization.
ifconfig and bogus ethernet address (4b:57:4b:57:4b:57) has been
hacked around. I'll revisit this when I have a clue whats going on.
Reviewed by: obrien
been so positive that I'm going to go ahead and commit this now rather
than do another round of patches.
My Adaptec 1460D works great with these changes.
NICs. (Finally!) The PCMCIA, ISA and PCI varieties are all supported,
though only the ISA and PCI ones will work on the alpha for now.
PCCARD, ISA and PCI attachments are all provided. Also provided an
ancontrol(8) utility for configuring the NIC, man pages, and updated
pccard.conf.sample. ISA cards are supported in both ISA PnP and hard-wired
mode, although you must configure the kernel explicitly to support the
hardwired mode since you have to know the I/O address and port ahead
of time.
Special thanks to Doug Ambrisko for doing the initial newbus hackery
and getting it to work in infrastructure mode.
Collect together the components of several drivers and export eisa from
the i386-only area (It's not, it's on some alphas too). The code hasn't
been updated to work on the Alpha yet, but that can come later.
Repository copies were done a while ago.
Moving these now keeps them in consistant place across the 4.x series
as the newbusification progresses.
Submitted by: mdodd
things like sound cards can get called "Parallel port". A note to the
unwary; the isa-pnp devices in the system are probed like PCI - each
device ID is passed to *all* isa probe routines to find the best match.
If the driver is not prepared to deal with this, it must abort in this
scenario or it will try and claim all PnP devices.
Update list of supported products.
Adjust probe message to include the ASC3030.
advansys.c:
Fix a long standing bug in the error recovery strategy. In order
to keep recovery simple, we freeze the SIMQ, stopping the XPT from
submitting new requests. Unfortunately, we also will freeze the
SIMQ if bus_dmamap_load blocks or we run out of controller resources.
On cards with limited resources it was possible to freeze the
SIM a second time and never unfreeze it. Now we more carefully
track our exception state so we never freeze the SIMQ more than
once.
Don't rely on pointers fitting in a 32bit field stored in the
per-transaction data structures on the card. Use an index to
an array of transaction mapping structures instead. This should
allow this driver to work on the Alpha.
Deal with the ASC3030 which is almost idistinguishable from the
ASC3050. Unfortunately the ASC3030 does not work at Ultra speeds,
so if we can't find an eeprom, we must assume that ultra is disabled.
The SIIG cards using the 3030 do not have eeproms. As a side effect,
we now honor the ultra disable bit in the eeprom if it is present.
Don't bother attempting to write corrected eeprom data back to the
eeprom. We can function just fine if the data is corrupted and
I'd rather not risk messing up the user's eeprom.
Modify the interrupt handler to catch latched external bus rests.
Dynamically determine the maximum number of S/G elements we can
map at a single time. The nature of the firmware interface for
these cards makes this value dependent on the number of "queues"
the card can support.
advlib.c:
advlib.h:
advmcode.c:
advmcode.h:
Synchronize with the latest firmware image released in the
Linux Advansys driver.
USB-EL1202A chipset. Between this and the other two drivers, we should
have support for pretty much every USB ethernet adapter on the market.
The only other USB chip that I know of is the SMC USB97C196, and right
now I don't know of any adapters that use it (including the ones made
by SMC :/ ).
Note that the CATC chip supports a nifty feature: read and write combining.
This allows multiple ethernet packets to be transfered in a single USB
bulk in/out transaction. However I'm again having trouble with large
bulk in transfers like I did with the ADMtek chip, which leads me to
believe that our USB stack needs some work before we can really make
use of this feature. When/if things improve, I intend to revisit the
aue and cue drivers. For now, I've lost enough sanity points.
Do not not not call m_freem() in the txeof routines. Let the netisr routine
do it. This also makes the tx netisr queuing much simpler (I can just use
another ifqueue instead of the mess I had before.)
Thanks to Bosko Milekic for making me actually think about what I was
doing for a minute.
Note1: the correct interrupt level is invoked correctly for each driver.
For this purpose, drivers request the bus before being able to
call BUS_SETUP_INTR and BUS_TEARDOWN_INTR call is forced by the ppbus
core when drivers release it. Thus, when BUS_SETUP_INTR is called
at ppbus driver level, ppbus checks that the caller owns the
bus and stores the interrupt handler cookie (in order to unregister
it later).
Printing is impossible while plip link is up is still TRUE.
vpo (ZIP driver) and lpt are make in such a way that
using the ZIP and printing concurrently is permitted is also TRUE.
Note2: specific chipset detection is not done by default. PPC_PROBE_CHIPSET
is now needed to force chipset detection. If set, the flags 0x40
still avoid detection at boot.
Port of the pcf(4) driver to the newbus system (was previously directly
connected to the rootbus and attached by a bogus pcf_isa_probe function).
- Add vendor/device ID for Corega USB-T ethernet adapter to necessary
places so that it will work with the kue driver.
- Add vendor/device ID for CATC Netmate devices for driver to be added
soon.
- Get really crazy about netisr stuff: avoid doing any mbuf allocations
or deallocations at splbio/splusb.
- Fix if_aue driver so that it works with LinkSys USB100TX: you need
to flip the GPIO bits just the right way to put the PHY in the right
mode.
