it in detail.
When setting media, don't error out when a specific media is selected.
# Note: There may be some issues still here since the EtherJet PC Card doesn't
# conform to the datasheet. Many different kinds of dongles can be plugged in
# and it is unknown how to ask which one it is.
Also, add a /* bad! */ comment to a 1/2 second delay after we set the
DC/DC parameters. This should be a *sleep of some sort for !cold.
Fortunately it is the only one and is only used when setting media, so
the benefit from removing it is small. Unfortunately, it likely
serves as an exemplar of good programming techniques, which it isn't.
it. Bad imp. Removing us dips us under 10,000 in size too.
o Replace an unconditional 30ms DELAY (yes, busy wait) with a check of the
SIBUSY bit in the SelfST register before accessing the eeprom. This changes
the time to read the EEPROM from 2 * 20 * 30ms (1.2s) to < 20*25us (.0005s)
and make the attach of the card tolerable when ethernet media is present.
Include data from the datasheet about why this works. While this is a 2500x
speed increase, it doesn't really matter at all once the card is probed...
o set dev earlier in softc.
o remove unused fields from softc and args from cs_alloc_irq
o remove some commented code that will never be implemented.
o Don't try to send a packet and see if it worked. We don't
need this anymore, and it doesn't add any value.
o tweaks for BNC and AUI.
o limit possible time hung in the kernel to 4s rather than 40s.
they can re-added. Remove CS_NAME. Don't whine when there's an
ignored checksum error: User has said STFU, so we should S the FU.
(remove mandated properties).
- Add a mutex to the softc to protect the softc and the device hardware.
- Add a private timer to manage transmit watchdogs rather than using
if_timer/if_watchdog.
- Setup the interrupt handler after ether_ifattach().
Tested by: imp
10BaseT' since it required 10BaseT to have carrier to switch to it.
This chip makes it hard to do proper auto, so we don't do it. We
can't test carrier on things easily.
Don't insist on carrier when we set the media. Don't report failures.
Remove a 1s! delay that appears to not be needed.
With these patches, and John Baldwin's patches, I'm able to pass
packets on my IBM EtherJet card again.
o When forced to be 10baseT, don't require that the 10baseT interface
have link to succeed. Still require it for IFM_AUTO, however, since it
appears that there's no way to tell if a specific type of interface
worked. I'm doing a web search for a datasheet now to see if there's
anything obvious.
o Minor incidental formatting nits, including collapsing code of the form
if (foo) {
bar();
} else {
if (baz)
bing();
}
into:
if (foo) {
bar();
} else if (baz) {
bing();
}
to save an indentation level.
o Remove stray reference to 3.x config file syntax.
# I believe John's patches still apply after this...
systems where the CardBus bridge was connected to a APIC. The case
where the probe routine is told to not setup the IRQ was mishandled
but the error was masked in the case where the IRQ was a valid one
for the card.
MFC after: 1 week
if_watchdog, etc., or in functions used only in these methods.
In all other functions in the driver use device_printf().
- Use __func__ instead of typing function name.
Submitted by: Alex Lyashkov <umka sevcity.net>
flag isn't enough - the filter needs to be set up too, or no multicast frames
are accepted.
Sponsored by: Philips Industrial Applications (indirectly)
MFC after: 3 days
could get an interrupt after we free the ifp, and the interrupt
handler depended on the ifp being still alive, this could, in theory,
cause a crash. Eliminate this possibility by moving the if_free to
after the bus_teardown_intr() call.
IFF_DRV_RUNNING, as well as the move from ifnet.if_flags to
ifnet.if_drv_flags. Device drivers are now responsible for
synchronizing access to these flags, as they are in if_drv_flags. This
helps prevent races between the network stack and device driver in
maintaining the interface flags field.
Many __FreeBSD__ and __FreeBSD_version checks maintained and continued;
some less so.
Reviewed by: pjd, bz
MFC after: 7 days
struct ifnet or the layer 2 common structure it was embedded in have
been replaced with a struct ifnet pointer to be filled by a call to the
new function, if_alloc(). The layer 2 common structure is also allocated
via if_alloc() based on the interface type. It is hung off the new
struct ifnet member, if_l2com.
This change removes the size of these structures from the kernel ABI and
will allow us to better manage them as interfaces come and go.
Other changes of note:
- Struct arpcom is no longer referenced in normal interface code.
Instead the Ethernet address is accessed via the IFP2ENADDR() macro.
To enforce this ac_enaddr has been renamed to _ac_enaddr.
- The second argument to ether_ifattach is now always the mac address
from driver private storage rather than sometimes being ac_enaddr.
Reviewed by: sobomax, sam
EtherJet, the interrupt is selected in the eeprom based on the layout
of the PC Card board. Since this is encoded into the EEPROM, and has
no relationship to the IRQ that the pccard bridge routes the PC Card's
interrupt pin to.
As such, stop writing to that register. This gets my EtherJet working.
# The eeprom reading code appears to be totally wrong for my EtherJet
# card. This causes the card to bogusly detect the media options
# available.
if the link-level address has been initialized already.
The majority of modern drivers never does this and works fine, which
makes me think that the check is totally unnecessary and a residue
of cut&paste from other drivers.
This change is done to simplify locking because now almost none of the
drivers uses this field. The exceptions are "ct" "ctau" and "cx"
where i am not sure if i can remove that part.
o Fix minor type problems
o Fix minor problem with a couple debug printfs.
o Default to a sane media type when none is reported.
o Minor style changes
The PR complains this will fix the IBM 300GL cards.
Submitted by: Max Gotlib
PR: 11462
if_xname, if_dname, and if_dunit. if_xname is the name of the interface
and if_dname/unit are the driver name and instance.
This change paves the way for interface renaming and enhanced pseudo
device creation and configuration symantics.
Approved By: re (in principle)
Reviewed By: njl, imp
Tested On: i386, amd64, sparc64
Obtained From: NetBSD (if_xname)
o don't strip the Ethernet header from inbound packets; pass packets
up the stack intact (required significant changes to some drivers)
o reference common definitions in net/ethernet.h (e.g. ETHER_ALIGN)
o track ether_ifattach/ether_ifdetach API changes
o track bpf changes (use BPF_TAP and BPF_MTAP)
o track vlan changes (ifnet capabilities, revised processing scheme, etc.)
o use if_input to pass packets "up"
o call ether_ioctl for default handling of ioctls
Reviewed by: many
Approved by: re
attached and ifconfigable. The card doesn't interrupt yet.
Also, move towards bus space by introducing new macros/inline
functions which make such a move much easier than before.
These inline functions are setup now to work around an IBM EtherJet
pccard cardbus bridge incompatibility. The card works in 8 bit mode,
but not in 16-bit mode when it is connected to a cardbus bridge for
reasons unknown. The Linux driver also has a similar workaround in
it.
Future work will include making the above workaround runtime
conditional rather than compile time conditional, as well as fixing
the interrupts in pccards and converting it to bus space.
parts: isa and pccard. The isa one is known to work with an IBM
EtherJet ISA card. The pccard one isn't known to work because the
EtherJet pccard I purchased recently arrived DOA :-(. I'll commit the
pccard.conf entry when the replacement card arrives.
I plan on MFC this in a week or two.
ether_ifdetach().
The former consolidates the operations of if_attach(), ng_ether_attach(),
and bpfattach(). The latter consolidates the corresponding detach operations.
Reviewed by: julian, freebsd-net
of the individual drivers and into the common routine ether_input().
Also, remove the (incomplete) hack for matching ethernet headers
in the ip_fw code.
The good news: net result of 1016 lines removed, and this should make
bridging now work with *all* Ethernet drivers.
The bad news: it's nearly impossible to test every driver, especially
for bridging, and I was unable to get much testing help on the mailing
lists.
Reviewed by: freebsd-net
This means that we will not have to have a bpf and a non-bpf version
of our driver modules.
This does not open any security hole, because the bpf core isn't loadable
The drivers left unchanged are the "cross platform" drivers where the respective
maintainers are urged to DTRT, whatever that may be.
Add a couple of missing FreeBSD tags.
i386 platform boots, it is no longer ISA-centric, and is fully dynamic.
Most old drivers compile and run without modification via 'compatability
shims' to enable a smoother transition. eisa, isapnp and pccard* are
not yet using the new resource manager. Once fully converted, all drivers
will be loadable, including PCI and ISA.
(Some other changes appear to have snuck in, including a port of Soren's
ATA driver to the Alpha. Soren, back this out if you need to.)
This is a checkpoint of work-in-progress, but is quite functional.
The bulk of the work was done over the last few years by Doug Rabson and
Garrett Wollman.
Approved by: core
reported bug.
At using tcpdump for cs interface, tcpdump only dump packet which
src or dst MAC-address is cs interface. cs interface can't look up
packet between others.
Submitted by: MIHIRA "Sanpei" Yoshiro <sanpei@sanpei.org>
