I'll clear how it's supposed to work with Bernhard and then look
at enabling this in the correct situations.
But this -does- enable HT RTS protection (using the appropriate legacy
rates) if this bit of code is enabled.
instead of 0x100000. As a side effect, an amd64 kernel now loads at
physical address 0x200000 instead of 0x100000. This is probably for the
best because it avoids the use of a 2MB page mapping for the first 1MB of
the kernel that also spans the fixed MTRRs. However, getmemsize() still
thinks that the kernel loads at 0x100000, and so the physical memory between
0x100000 and 0x200000 is lost. Fix this problem by replacing the hard-wired
constant in getmemsize() by a symbol "kernphys" that is defined by the
linker script.
In collaboration with: kib
(e.g. powerpc64), this looks in a slightly different default path than now,
specifying both $MACHINE and $MACHINE_ARCH:
MIRROR/pub/FreeBSD/releases/`uname -p`/`uname -m`/`uname -r`
How to handle TBEMD properly probably merits some more discussion, but,
since no such 9.0-CURRENT distfiles exist at the moment, all existing
mirrors presently fail anyway.
registered in g_gate_units array and when its sc_provider field is
filled. If during this period g_gate_units is accessed by another
thread that is checking for provider name collision the crash is
possible.
Fix this by adding sc_name field to struct g_gate_softc. In
g_gate_create() when g_gate_softc is created but sc_provider is still
not sc_name points to provider name stored in the local array.
Approved by: pjd (mentor)
Reported by: Freddie Cash <fjwcash@gmail.com>
MFC after: 1 week
just for Redboot.
At some point we're going to need to build options for different
boot environments - for example, the UBoot setups I've seen simply
have the MAC address hard-coded at a fixed location in flash.
The OpenWRT support simply yanks the if_arge MAC directly from that
in code, rather than trying to find a uboot environment to pull it
from.
memory detected from Redboot, or overrides the "otherwise" case
if no Redboot information was found.
Some AR71XX platforms don't use Redboot (eg TP-LINK devices using
UBoot; some later Ubiquiti devices which apparently also use
UBoot) and at least one plain out lies - the Ubiquiti LS-SR71A
Redboot says there's 16mb of RAM when in fact there's 32mb.
A more "clean" solution will be needed at a later date.
The AR913x/AR724x USB lives at a different offset to the AR71xx
USB, so this needs to be either adjusted for in a subsequent
commit, or updated in hints for kernels compiled for those
platforms.
Submitted by: Luiz Otavio O Souzau <loos.br@gmail.com>
syncing for Hummingbird and Sabre bridges should be applied with every
BUS_DMASYNC_POSTREAD instead of in a wrapper around interrupt handlers
for devices behind PCI-PCI bridges only as suggested by the documentation
(code for the latter actually exists in OpenSolaris but is disabled by
default), which also makes more sense.
- Take advantage of the ofw_pci_setup_device method introduced in r220038
for disabling bus parking for certain EBus bridges in order to
- Mark some unused parameters as such.
register changes when compiled with SCHIZO_DEBUG and take advantage
of them.
- Add support for the XMITS Fireplane/Safari to PCI-X bridges. I tought
I'd need this for a Sun Fire 3800, which then turned out to not being
equipped with such a bridge though. The support for these should be
complete but given that it hasn't actually been tested probing is
disabled for now.
This required a way to alter the XMITS configuration in case a PCI-X
device is found further down the device tree so the sparc64 specific
ofw_pci kobj was revived with a ofw_pci_setup_device method, which is
called by the ofw_pcibus code for every device added.
- A closer inspection of the OpenSolaris code indicates that consistent
DMA flushing/syncing as well as the block store workaround should be
applied with every BUS_DMASYNC_POSTREAD instead of in a wrapper around
interrupt handlers for devices behind PCI-PCI bridges only as suggested
by the documentation (code for the latter actually exists in OpenSolaris
but is disabled by default), which also makes more sense.
- Add a workaround for Casinni/Skyhawk combinations. Chances are that
this solves the crashes seen when using the the on-board Casinni NICs
of Sun Fire V480 equipped with centerplanes other than 501-6780 or
501-6790. This also takes advantage of the ofw_pci_setup_device method.
- Mark some unused parameters as such.
to be a meta-target, and having it do this avoids it spewing files all
over the source tree by default (and possible recursive tarring if
distributing a src tarball).
This seems to have been a part of a bigger patch by dchagin that either
haven't been committed or committed partially.
Submitted by: dchagin, nox
MFC after: 2 weeks
- implement baseic stubs for capget, capset, prctl PR_GET_KEEPCAPS
and prctl PR_SET_KEEPCAPS.
- add SCM_CREDS support to sendmsg and recvmsg
- modify sendmsg to ignore control messages if not using UNIX
domain sockets
This should allow linux pulse audio daemon and client work on FreeBSD
and interoperate with native counter-parts modulo the differences in
pulseaudio versions.
PR: kern/149168
Submitted by: John Wehle <john@feith.com>
Reviewed by: netchild
MFC after: 2 weeks
And drop dummy definitions for those system calls.
This may transiently break the build.
PR: kern/149168
Submitted by: John Wehle <john@feith.com>
Reviewed by: netchild
MFC after: 2 weeks
by default.
Adventourous souls with an AR9220/AR9280 or later and who have a device
that sends PS-POLL frames may wish to try tinkering with this option and
get back to me.
Linux ath9k only enables this for AR9280 and later NICs; so
create a capability for it so it isn't enabled for earlier
NICs.
Enabling hardware PS-POLL support will come in a later commit
and will be disabled by default.
Since signal trampolines are copied to the shared page do not need to
leave place on the stack for it. Forgotten in the previous commit.
MFC after: 1 Week
Even though they map to setting the error filter register,
ath9k also writes them untouched to AR_RX_FILTER.
The Force-BSSID match bit can stay high, as it maps to a
misc mode register setting rather than an RX filter bit.
The phyerr, radar and bssid-match bits aren't real bits, they map
to enabling bits in other registers. Move those out of the way of
valid RX filter bits.
Add a few new fields from ath9k - compba, ps-poll, mcast-bcast-all.
