This prevents incorrect subversion revision detection when "git svn" is
not being used to get the sources but git is available. Previously old
subversion revisions included in commit messages were favoured over the
more recent and correct revisions in git notes.
For example cf1f355747 represents r315395 but was treated as r313908
which is referenced in the commit message. Commits following
r315395/cf1f35574722 but before another commit with a git-svn-id
reference in the commit message would be treated as r313908 as well.
Patch from PR updated to accommodate the initial four space indent in
`git log` ouptut.
PR: 221848
Submitted by: Fabian Keil
Obtained from: ElectroBSD
MFC after: 2 weeks
Prior to the change they were subject to extreme false sharing.
In particular this change shaves about 3 seconds real time of -j 80 buildkernel.
Reviewed by: alc, markj
Differential Revision: https://reviews.freebsd.org/D12281
Sometimes it is necessary to combine several gpio pins into an ad-hoc bus
and manipulate the pins as a group. In such cases manipulating the pins
individualy is not an option, because the value on the "bus" assumes
potentially-invalid intermediate values as each pin is changed in turn. Note
that the "bus" may be something as simple as a bi-color LED where changing
colors requires changing both gpio pins at once, or something as complex as
a bitbanged multiplexed address/data bus connected to a microcontroller.
In addition to the absolute requirement of simultaneously changing the
output values of driven pins, a desirable feature of these new methods is to
provide a higher-performance mechanism for reading and writing multiple
pins, especially from userland where pin-at-a-time access incurs a noticible
syscall time penalty.
These new interfaces are NOT intended to abstract away all the ugly details
of how gpio is implemented on any given platform. In fact, to use these
properly you absolutely must know something about how the gpio hardware is
organized. Typically there are "banks" of gpio pins controlled by registers
which group several pins together. A bank may be as small as 2 pins or as
big as "all the pins on the device, hundreds of them." In the latter case, a
driver might support this interface by allowing access to any 32 adjacent
pins within the overall collection. Or, more likely, any 32 adjacent pins
starting at any multiple of 32. Whatever the hardware restrictions may be,
you would need to understand them to use this interface.
In additional to defining the interfaces, two example implementations are
included here, for imx5/6, and allwinner. These represent the two primary
types of gpio hardware drivers. imx6 has multiple gpio devices, each
implementing a single bank of 32 pins. Allwinner implements a single large
gpio number space from 1-n pins, and the driver internally translates that
linear number space to a bank+pin scheme based on how the pins are grouped
into control registers. The allwinner implementation imposes the restriction
that the first_pin argument to the new functions must always be pin 0 of a
bank.
Differential Revision: https://reviews.freebsd.org/D11810
for analyzing the radix tree structures and reporting on the number, and
sizes, of maximal intervals of free blocks. The report includes the number
of maximal intervals, and also the number of them in each of several size
ranges, from small (size 1, or 3 to 4) to large (28657 to 46367) with size
boundaries defined by Fibonacci numbers. The report is written in the test
tool with the 's' command, or in a running kernel by sysctl.
The analysis of the radix tree frequently computes the position of the lone
bit set in a u_daddr_t, a computation that also appears in leaf allocation.
That computation has been moved into a function of its own, and optimized
for cases where an inlined machine instruction can replace the usual binary
search.
Submitted by: Doug Moore <dougm@rice.edu>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D11906
it to a random value between 100 and 1123, rather than 0 as before.
Submitted by: Marie Helene Kvello-Aune <marieheleneka@gmail.com>
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D5336
Since the efipart rewrite, the chain command was looking for device
handle using interface applicable only for net devices. Disk
partitions and zfs pools need their own approach to find the proper handle.
Reviewed by: imp
Differential Revision: https://reviews.freebsd.org/D12287
namecache_ts differs from mere namecache by few fields placed mid struct.
The access to the last element (the name) is thus special-cased.
The standard solution is to put new fields at the very beginning anad
embedd the original struct. The pointer shuffled around points to the
embedded part. If needed, access to new fields can be gained through
__containerof.
MFC after: 1 week
Permit a deflateParams() parameter change as soon as possible.
This change fixes compression errors seen when the embedded Tomcat
web server of a UniFi Controller zlib compresses responses. Given
that Tomcat just uses Java/OpenJDK which in turn employs zlib for
its compression/decompression support, this bug might very well
affect other applications, too.
PR: 222136
This commit allows a parameter change even if the input data has
not all been compressed and copied to the application output
buffer, so long as all of the input data has been compressed to
the internal pending output buffer. This also allows an immediate
deflateParams change so long as there have been no deflate calls
since initialization or reset.
Obtained from: upstream (f9694097dd69354b03cb8af959094c7f260db0a1)
This module is specific to a single Marvel board that we currently
only support in 64-bit mode. Remove it from the build otherwise. It
likely should be completely removed, but this unbreaks x86 building.
Noticed by: sbruno@
the driver in a place where it will be built for all targets. x86 doesn't
have all the required build bits for this device.
Move the uart(4) device mvebu to arm64 only.
lock if both old and new pages use the same underlying lock. Convert
existing places to use the helper instead of inlining it. Use the
optimization in vm_object_page_remove().
Suggested and reviewed by: alc, markj
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
have a scope ID. Change size of the searched scope ID to the full
16-bits. There can typically be more than 255 interfaces.
Suggested by: ae @
MFC after: 1 week
Sponsored by: Mellanox Technologies
This patch enables using NETA driver on Marvell Armada 3700 SoC
by introducing new compatible string, modifying clock source
obtaining and also excluding unnecessary parts.
The driver is added as a build option for arm64 platforms as well.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12258
Now the virtual address of received buffer is taken from a software ring.
Thanks to this, we can use the NETA driver on 64 bits architecture and
avoid 32-bit buf_cookie descriptor field limitation.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12257
This patch adds support for UART in Armada 3700 family.
It exposes both low-level UART interface, as well as
standard driver methods.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12250
Enabled driver can be used on boards equipped with Marvell Armada 3700 SoC.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12256
This patch reuses ehci_mv driver by adding a support for the new
compatible string and adding ehci_mv.c to list of available options
for arm64 platforms.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12255
illumos/illumos-gate@1702cce7511702cce751
FreeBSD note: rather than merging the zpool.8 update I copied the zpool
scrub section from the illumos zpool.1m to FreeBSD zpool.8 almost
verbatim. Now that the illumos page uses the mdoc format, it was an
easier option. Perhaps the change is not in perfect compliance with the
FreeBSD style, but I think that it is acceptible.
https://www.illumos.org/issues/8414
This issue tracks the port of scrub pause from ZoL: https://github.com/zfsonlinux/zfs/pull/6167
Currently, there is no way to pause a scrub. Pausing may be useful when
the pool is busy with other I/O to preserve bandwidth.
Description
This patch adds the ability to pause and resume scrubbing. This is achieved
by maintaining a persistent on-disk scrub state. While the state is 'paused'
we do not scrub any more blocks. We do however perform regular scan
housekeeping such as freeing async destroyed and deadlist blocks while paused.
Motivation and Context
Scrub pausing can be an I/O intensive operation and people have been asking
for the ability to pause a scrub for a while. This allows one to preserve scrub
progress while freeing up bandwidth for other I/O.
Reviewed by: George Melikov <mail@gmelikov.ru>
Reviewed by: Brian Behlendorf <behlendorf1@llnl.gov>
Reviewed by: Brad Lewis <brad.lewis@delphix.com>
Reviewed by: Serapheim Dimitropoulos <serapheim@delphix.com>
Reviewed by: Matt Ahrens <mahrens@delphix.com>
Approved by: Dan McDonald <danmcd@joyent.com>
Author: Alek Pinchuk <apinchuk@datto.com>
MFC after: 2 weeks
Enabled driver can be used on boards equipped with Marvell Armada
3700/7k/8k SoCs.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12253
This driver will be used by Marvell Armada 3700 and 7k/8k SoC families.
The same, generic xhci device also appears in Armada 380, so we are reusing
driver.
This patch also adds xhci_mv.c entry to the arm64 files list.
Submitted by: Patryk Duda <pdk@semihalf.com>
Obtained from: Semihalf
Sponsored by: Semihalf
Differential Revision: https://reviews.freebsd.org/D12252
Workaround problem that ifa_ifwithaddr() also matches the scope ID of
the IPv6 address when searching for a maching IPv6 address. For now
simply try all valid scope IDs until a match is found.
MFC after: 1 week
Sponsored by: Mellanox Technologies
use of the linux_poll_wakeup() function from unsafe contexts, which
can lead to use-after-free issues.
Instead of calling linux_poll_wakeup() directly use the wake_up()
family of functions in the LinuxKPI to do this.
Bump the FreeBSD version to force recompilation of external kernel modules.
MFC after: 1 week
Sponsored by: Mellanox Technologies
- Capture exit code in pipeline and test in output.
- Drop awk use in favor of `sleep 2`. This helps guarantee the EPIPE
behavior without the potential race.
