- improved pipe calculation which does not degrade under heavy loss
- engaging in Loss Recovery earlier under adverse conditions
- Rescue Retransmission in case some of the trailing packets of a request got lost
All above changes are toggled with the sysctl "rfc6675_pipe" (disabled by default).
Reviewers: #transport, tuexen, lstewart, slavash, jtl, hselasky, kib, rgrimes, chengc_netapp.com, thj, #manpages, kbowling, #netapp, rscheff
Reviewed By: #transport
Subscribers: imp, melifaro
MFC after: 2 weeks
Sponsored by: NetApp, Inc.
Differential Revision: https://reviews.freebsd.org/D18985
Consider the currently in-use TCP options when
calculating the amount of new data to be injected during
SACK loss recovery. That addresses the effect that very small
(new) segments could be injected on partial ACKs while
still performing a SACK loss recovery.
Reported by: Liang Tian
Reviewed by: tuexen, chengc_netapp.com
MFC after: 2 weeks
Sponsored by: NetApp, Inc.
Differential Revision: https://reviews.freebsd.org/D26446
Adding proper accounting of sacked_bytes and (per-ACK)
delivered data to the SACK scoreboard. This will
allow more aspects of RFC6675 to be implemented as well
as Proportional Rate Reduction (RFC6937).
Prior to this change, the pipe calculation controlled with
net.inet.tcp.rfc6675_pipe was also susceptible to incorrect
results when more than 3 (or 4) holes in the sequence space
were present, which can no longer all fit into a single
ACK's SACK option.
Reviewed by: kbowling, rgrimes (mentor)
Approved by: rgrimes (mentor, blanket)
MFC after: 3 weeks
Sponsored by: NetApp, Inc.
Differential Revision: https://reviews.freebsd.org/D18624
r357614 added CTLFLAG_NEEDGIANT to make it easier to find nodes that are
still not MPSAFE (or already are but aren’t properly marked).
Use it in preparation for a general review of all nodes.
This is non-functional change that adds annotations to SYSCTL_NODE and
SYSCTL_PROC nodes using one of the soon-to-be-required flags.
Mark all obvious cases as MPSAFE. All entries that haven't been marked
as MPSAFE before are by default marked as NEEDGIANT
Approved by: kib (mentor, blanket)
Commented by: kib, gallatin, melifaro
Differential Revision: https://reviews.freebsd.org/D23718
a single instance: use snd_recover also where sack_newdata was used.
Submitted by: Richard Scheffenegger
Differential Revision: https://reviews.freebsd.org/D18811
The lowest SACK block is used when multiple Blocks would be elegible as
DSACK blocks ACK blocks get reordered - while maintaining the ordering of
SACK blocks not relevant in the DSACK context is maintained.
Reviewed by: rrs@, tuexen@
Obtained from: Richard Scheffenegger
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D21038
get BBRv1 into the tree. This fixes the DSACK bug but
is also needed by BBR. We have yet to go two more
one will be for the pacing code (tcp_ratelimit.c) and
the second will be for the new updated LRO code that
allows a transport to know the arrival times of packets
and (tcp_lro.c). After that we should finally be able
to get BBRv1 into head.
Sponsored by: Netflix Inc
Differential Revision: https://reviews.freebsd.org/D20908
This adds initial support for RFC 2883.
Submitted by: Richard Scheffenegger
Reviewed by: rrs@
Differential Revision: https://reviews.freebsd.org/D19334
Mainly focus on files that use BSD 3-Clause license.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
Special thanks to Wind River for providing access to "The Duke of
Highlander" tool: an older (2014) run over FreeBSD tree was useful as a
starting point.
can use them. Gather all TCP tunables in tcp_var.h in one place and
alphabetically sort them, to ease maintainance of the list.
Don't copy and paste declarations in tcp_stacks/fastpath.c.
In case of the empty queue tp->snd_holes and tcp_sackhole_insert()
failing due to memory shortage, tp->snd_holes will be empty.
This problem was hit when stress tests where performed by pho.
PR: 215513
Reported by: pho
Tested by: pho
Sponsored by: Netflix, Inc.
to do is to clean up the timer handling using the async-drain.
Other optimizations may be coming to go with this. Whats here
will allow differnet tcp implementations (one included).
Reviewed by: jtl, hiren, transports
Sponsored by: Netflix Inc.
Differential Revision: D4055
other end till it reaches predetermined threshold which is 3 for us right now.
Once that happens, we trigger fast-retransmit to do loss recovery.
Main problem with the current implementation is that we don't honor SACK
information well to detect whether an incoming ack is a dupack or not. RFC6675
has latest recommendations for that. According to it, dupack is a segment that
arrives carrying a SACK block that identifies previously unknown information
between snd_una and snd_max even if it carries new data, changes the advertised
window, or moves the cumulative acknowledgment point.
With the prevalence of Selective ACK (SACK) these days, improper handling can
lead to delayed loss recovery.
With the fix, new behavior looks like following:
0) th_ack < snd_una --> ignore
Old acks are ignored.
1) th_ack == snd_una, !sack_changed --> ignore
Acks with SACK enabled but without any new SACK info in them are ignored.
2) th_ack == snd_una, window == old_window --> increment
Increment on a good dupack.
3) th_ack == snd_una, window != old_window, sack_changed --> increment
When SACK enabled, it's okay to have advertized window changed if the ack has
new SACK info.
4) th_ack > snd_una --> reset to 0
Reset to 0 when left edge moves.
5) th_ack > snd_una, sack_changed --> increment
Increment if left edge moves but there is new SACK info.
Here, sack_changed is the indicator that incoming ack has previously unknown
SACK info in it.
Note: This fix is not fully compliant to RFC6675. That may require a few
changes to current implementation in order to keep per-sackhole dupack counter
and change to the way we mark/handle sack holes.
PR: 203663
Reviewed by: jtl
MFC after: 3 weeks
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D4225
suggested by RFC 6675.
Currently differnt places in the stack tries to guess this in suboptimal ways.
The main problem is that current calculations don't take sacked bytes into
account. Sacked bytes are the bytes receiver acked via SACK option. This is
suboptimal because it assumes that network has more outstanding (unacked) bytes
than the actual value and thus sends less data by setting congestion window
lower than what's possible which in turn may cause slower recovery from losses.
As an example, one of the current calculations looks something like this:
snd_nxt - snd_fack + sackhint.sack_bytes_rexmit
New proposal from RFC 6675 is:
snd_max - snd_una - sackhint.sacked_bytes + sackhint.sack_bytes_rexmit
which takes sacked bytes into account which is a new addition to the sackhint
struct. Only thing we are missing from RFC 6675 is isLost() i.e. segment being
considered lost and thus adjusting pipe based on that which makes this
calculation a bit on conservative side.
The approach is very simple. We already process each ack with sack info in
tcp_sack_doack() and extract sack blocks/holes out of it. We'd now also track
this new variable sacked_bytes which keeps track of total sacked bytes reported.
One downside to this approach is that we may get incorrect count of sacked_bytes
if the other end decides to drop sack info in the ack because of memory pressure
or some other reasons. But in this (not very likely) case also the pipe
calculation would be conservative which is okay as opposed to being aggressive
in sending packets into the network.
Next step is to use this more accurate pipe estimation to drive congestion
window adjustments.
In collaboration with: rrs
Reviewed by: jason_eggnet dot com, rrs
MFC after: 2 weeks
Sponsored by: Limelight Networks
Differential Revision: https://reviews.freebsd.org/D3971
to this event, adding if_var.h to files that do need it. Also, include
all includes that now are included due to implicit pollution via if_var.h
Sponsored by: Netflix
Sponsored by: Nginx, Inc.
This will be used by the incoming Enhanced RTT Khelp module.
Sponsored by: FreeBSD Foundation
Submitted by: David Hayes <dahayes at swin edu au>
Reviewed by: bz and others (as part of a larger patch)
MFC after: 3 months
Control Algorithms for FreeBSD" FreeBSD Foundation funded project. More details
about the project are available at: http://caia.swin.edu.au/freebsd/5cc/
- Add a KPI and supporting infrastructure to allow modular congestion control
algorithms to be used in the net stack. Algorithms can maintain per-connection
state if required, and connections maintain their own algorithm pointer, which
allows different connections to concurrently use different algorithms. The
TCP_CONGESTION socket option can be used with getsockopt()/setsockopt() to
programmatically query or change the congestion control algorithm respectively
from within an application at runtime.
- Integrate the framework with the TCP stack in as least intrusive a manner as
possible. Care was also taken to develop the framework in a way that should
allow integration with other congestion aware transport protocols (e.g. SCTP)
in the future. The hope is that we will one day be able to share a single set
of congestion control algorithm modules between all congestion aware transport
protocols.
- Introduce a new congestion recovery (TF_CONGRECOVERY) state into the TCP stack
and use it to decouple the meaning of recovery from a congestion event and
recovery from packet loss (TF_FASTRECOVERY) a la RFC2581. ECN and delay based
congestion control protocols don't generally need to recover from packet loss
and need a different way to note a congestion recovery episode within the
stack.
- Remove the net.inet.tcp.newreno sysctl, which simplifies some portions of code
and ensures the stack always uses the appropriate mechanisms for recovering
from packet loss during a congestion recovery episode.
- Extract the NewReno congestion control algorithm from the TCP stack and
massage it into module form. NewReno is always built into the kernel and will
remain the default algorithm for the forseeable future. Implementations of
additional different algorithms will become available in the near future.
- Bump __FreeBSD_version to 900025 and note in UPDATING that rebuilding code
that relies on the size of "struct tcpcb" is required.
Many thanks go to the Cisco University Research Program Fund at Community
Foundation Silicon Valley and the FreeBSD Foundation. Their support of our work
at the Centre for Advanced Internet Architectures, Swinburne University of
Technology is greatly appreciated.
In collaboration with: David Hayes <dahayes at swin edu au> and
Grenville Armitage <garmitage at swin edu au>
Sponsored by: Cisco URP, FreeBSD Foundation
Reviewed by: rpaulo
Tested by: David Hayes (and many others over the years)
MFC after: 3 months
"Whitspace" churn after the VIMAGE/VNET whirls.
Remove the need for some "init" functions within the network
stack, like pim6_init(), icmp_init() or significantly shorten
others like ip6_init() and nd6_init(), using static initialization
again where possible and formerly missed.
Move (most) variables back to the place they used to be before the
container structs and VIMAGE_GLOABLS (before r185088) and try to
reduce the diff to stable/7 and earlier as good as possible,
to help out-of-tree consumers to update from 6.x or 7.x to 8 or 9.
This also removes some header file pollution for putatively
static global variables.
Revert VIMAGE specific changes in ipfilter::ip_auth.c, that are
no longer needed.
Reviewed by: jhb
Discussed with: rwatson
Sponsored by: The FreeBSD Foundation
Sponsored by: CK Software GmbH
MFC after: 6 days
vnet.h, we now use jails (rather than vimages) as the abstraction
for virtualization management, and what remained was specific to
virtual network stacks. Minor cleanups are done in the process,
and comments updated to reflect these changes.
Reviewed by: bz
Approved by: re (vimage blanket)
(DPCPU), as suggested by Peter Wemm, and implement a new per-virtual
network stack memory allocator. Modify vnet to use the allocator
instead of monolithic global container structures (vinet, ...). This
change solves many binary compatibility problems associated with
VIMAGE, and restores ELF symbols for virtualized global variables.
Each virtualized global variable exists as a "reference copy", and also
once per virtual network stack. Virtualized global variables are
tagged at compile-time, placing the in a special linker set, which is
loaded into a contiguous region of kernel memory. Virtualized global
variables in the base kernel are linked as normal, but those in modules
are copied and relocated to a reserved portion of the kernel's vnet
region with the help of a the kernel linker.
Virtualized global variables exist in per-vnet memory set up when the
network stack instance is created, and are initialized statically from
the reference copy. Run-time access occurs via an accessor macro, which
converts from the current vnet and requested symbol to a per-vnet
address. When "options VIMAGE" is not compiled into the kernel, normal
global ELF symbols will be used instead and indirection is avoided.
This change restores static initialization for network stack global
variables, restores support for non-global symbols and types, eliminates
the need for many subsystem constructors, eliminates large per-subsystem
structures that caused many binary compatibility issues both for
monitoring applications (netstat) and kernel modules, removes the
per-function INIT_VNET_*() macros throughout the stack, eliminates the
need for vnet_symmap ksym(2) munging, and eliminates duplicate
definitions of virtualized globals under VIMAGE_GLOBALS.
Bump __FreeBSD_version and update UPDATING.
Portions submitted by: bz
Reviewed by: bz, zec
Discussed with: gnn, jamie, jeff, jhb, julian, sam
Suggested by: peter
Approved by: re (kensmith)
which is currently not protected by any type of lock. When triggered, the bug
would sometimes cause a panic when the TCP activity to an affected machine
eventually slowed during a lull. The panic only occurs if INVARIANTS is compiled
into the kernel, and has laid dormant for some time as a result of INVARIANTS
being off by default except in FreeBSD-CURRENT.
Switch to atomic operations in the locations where the variable is changed.
Reads have not been updated to be protected by atomics, so there is a
possibility of accounting errors in any given calculation where the variable is
read. This is considered unlikely to occur in the wild, and will not cause
serious harm on rare occasions where it does.
Thanks to Robert Watson for debugging help.
Reported by: Kamigishi Rei <spambox at haruhiism dot net>
Tested by: Kamigishi Rei <spambox at haruhiism dot net>
Reviewed by: silby
Approved by: re (rwatson), kensmith (mentor temporarily unavailable)
TCPSTAT_INC(), rather than directly manipulating the fields across the
kernel. This will make it easier to change the implementation of
these statistics, such as using per-CPU versions of the data structures.
MFC after: 3 days
from existing functions for initializing global state.
At this stage, the new per-vnet initializer functions are
directly called from the existing global initialization code,
which should in most cases result in compiler inlining those
new functions, hence yielding a near-zero functional change.
Modify the existing initializer functions which are invoked via
protosw, like ip_init() et. al., to allow them to be invoked
multiple times, i.e. per each vnet. Global state, if any,
is initialized only if such functions are called within the
context of vnet0, which will be determined via the
IS_DEFAULT_VNET(curvnet) check (currently always true).
While here, V_irtualize a few remaining global UMA zones
used by net/netinet/netipsec networking code. While it is
not yet clear to me or anybody else whether this is the right
thing to do, at this stage this makes the code more readable,
and makes it easier to track uncollected UMA-zone-backed
objects on vnet removal. In the long run, it's quite possible
that some form of shared use of UMA zone pools among multiple
vnets should be considered.
Bump __FreeBSD_version due to changes in layout of structs
vnet_ipfw, vnet_inet and vnet_net.
Approved by: julian (mentor)
container structures, depending on VIMAGE_GLOBALS compile time option.
Make VIMAGE_GLOBALS a new compile-time option, which by default will not
be defined, resulting in instatiations of global variables selected for
V_irtualization (enclosed in #ifdef VIMAGE_GLOBALS blocks) to be
effectively compiled out. Instantiate new global container structures
to hold V_irtualized variables: vnet_net_0, vnet_inet_0, vnet_inet6_0,
vnet_ipsec_0, vnet_netgraph_0, and vnet_gif_0.
Update the VSYM() macro so that depending on VIMAGE_GLOBALS the V_
macros resolve either to the original globals, or to fields inside
container structures, i.e. effectively
#ifdef VIMAGE_GLOBALS
#define V_rt_tables rt_tables
#else
#define V_rt_tables vnet_net_0._rt_tables
#endif
Update SYSCTL_V_*() macros to operate either on globals or on fields
inside container structs.
Extend the internal kldsym() lookups with the ability to resolve
selected fields inside the virtualization container structs. This
applies only to the fields which are explicitly registered for kldsym()
visibility via VNET_MOD_DECLARE() and vnet_mod_register(), currently
this is done only in sys/net/if.c.
Fix a few broken instances of MODULE_GLOBAL() macro use in SCTP code,
and modify the MODULE_GLOBAL() macro to resolve to V_ macros, which in
turn result in proper code being generated depending on VIMAGE_GLOBALS.
De-virtualize local static variables in sys/contrib/pf/net/pf_subr.c
which were prematurely V_irtualized by automated V_ prepending scripts
during earlier merging steps. PF virtualization will be done
separately, most probably after next PF import.
Convert a few variable initializations at instantiation to
initialization in init functions, most notably in ipfw. Also convert
TUNABLE_INT() initializers for V_ variables to TUNABLE_FETCH_INT() in
initializer functions.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
directly include only the header files needed. This reduces the
unneeded spamming of various headers into lots of files.
For now, this leaves us with very few modules including vnet.h
and thus needing to depend on opt_route.h.
Reviewed by: brooks, gnn, des, zec, imp
Sponsored by: The FreeBSD Foundation
for virtualization.
Instead of initializing the affected global variables at instatiation,
assign initial values to them in initializer functions. As a rule,
initialization at instatiation for such variables should never be
introduced again from now on. Furthermore, enclose all instantiations
of such global variables in #ifdef VIMAGE_GLOBALS blocks.
Essentialy, this change should have zero functional impact. In the next
phase of merging network stack virtualization infrastructure from
p4/vimage branch, the new initialization methology will allow us to
switch between using global variables and their counterparts residing in
virtualization containers with minimum code churn, and in the long run
allow us to intialize multiple instances of such container structures.
Discussed at: devsummit Strassburg
Reviewed by: bz, julian
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
from the vimage project, as per plan established at devsummit 08/08:
http://wiki.freebsd.org/Image/Notes200808DevSummit
Introduce INIT_VNET_*() initializer macros, VNET_FOREACH() iterator
macros, and CURVNET_SET() context setting macros, all currently
resolving to NOPs.
Prepare for virtualization of selected SYSCTL objects by introducing a
family of SYSCTL_V_*() macros, currently resolving to their global
counterparts, i.e. SYSCTL_V_INT() == SYSCTL_INT().
Move selected #defines from sys/sys/vimage.h to newly introduced header
files specific to virtualized subsystems (sys/net/vnet.h,
sys/netinet/vinet.h etc.).
All the changes are verified to have zero functional impact at this
point in time by doing MD5 comparision between pre- and post-change
object files(*).
(*) netipsec/keysock.c did not validate depending on compile time options.
Implemented by: julian, bz, brooks, zec
Reviewed by: julian, bz, brooks, kris, rwatson, ...
Approved by: julian (mentor)
Obtained from: //depot/projects/vimage-commit2/...
X-MFC after: never
Sponsored by: NLnet Foundation, The FreeBSD Foundation
virtualization work done by Marko Zec (zec@).
This is the first in a series of commits over the course
of the next few weeks.
Mark all uses of global variables to be virtualized
with a V_ prefix.
Use macros to map them back to their global names for
now, so this is a NOP change only.
We hope to have caught at least 85-90% of what is needed
so we do not invalidate a lot of outstanding patches again.
Obtained from: //depot/projects/vimage-commit2/...
Reviewed by: brooks, des, ed, mav, julian,
jamie, kris, rwatson, zec, ...
(various people I forgot, different versions)
md5 (with a bit of help)
Sponsored by: NLnet Foundation, The FreeBSD Foundation
X-MFC after: never
V_Commit_Message_Reviewed_By: more people than the patch
explicitly select write locking for all use of the inpcb mutex.
Update some pcbinfo lock assertions to assert locked rather than
write-locked, although in practice almost all uses of the pcbinfo
rwlock main exclusive, and all instances of inpcb lock acquisition
are exclusive.
This change should introduce (ideally) little functional change.
However, it lays the groundwork for significantly increased
parallelism in the TCP/IP code.
MFC after: 3 months
Tested by: kris (superset of committered patch)
directly to a merged model where only one callout, the next to fire,
is registered.
Instead of callout_reset(9) and callout_stop(9) the new function
tcp_timer_activate() is used which then internally manages the callout.
The single new callout is a mutex callout on inpcb simplifying the
locking a bit.
tcp_timer() is the called function which handles all race conditions
in one place and then dispatches the individual timer functions.
Reviewed by: rwatson (earlier version)
function may be called without any TCP SACK option blocks present. Protect
iteration over SACK option blocks by checking for SACK options present flag
first.
Bug reported by: wkoszek, keramida, Nicolas Blais
(tcp_sack_output_debug checks cached hints aginst computed values by walking the
scoreboard and reports discrepancies). The sack hinting code has been stable for
many months now so it is time for the debug code to go. Leaving tcp_sack_output_debug
ifdef'ed out in case we need to resurrect it at a later point.
