Specification of entire RSS table in the driver allows to spread traffic
more equally across CPUs/RSS channels if number of RSS channels is not
power of 2.
Reviewed by: philip
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
Differential Revision: https://reviews.freebsd.org/D8910
The ath10k firmware supports hardware WEP offload, and in native wifi mode
(or 802.3 ethernet mode, for that matter) the WEP key isn't actually included
in the TX payload from net80211. Instead, a separate firmware command is issued
that sets the default TX key to be the specified key.
However, net80211 doesn't at all inform the driver layer that this is
occuring - it just "expects" to be inserting WEP header information
when doing WEP TX, even with hardware encryption.
So, to better support the newer world order, turn the default TX key assignment
into a VAP method that can be overridden by the driver and ensure its wrapped
in a crypto begin/end set. That way it should be correctly atomic from the
point of view of keychanges (as long as the driver does the right thing.)
It'd be nice if we passed through to the key_set call a flag that says
"also make this the default key" - that's captured here by calling the
deftxkey method after the key_set method. Maybe I can do that later.
Note: this is a net80211 ABI change, and will require a kernel+modules
recompile. Happy Holidays, etc.
Tested:
* ath10k driver port
* rtwn_usb, WEP station
Add ACPI part for ig4 driver to make it work on Intel BayTrail SoC where
ig4 device is available only through ACPI
Reviewed by: avg
MFC after: 1 week
Differential Revision: https://reviews.freebsd.org/D8742
closed by r310302 for knote().
If KN_INFLUX | KN_SCAN flags are set for the note passed to knote() or
knote_fork(), i.e. the knote is scanned, we might erronously clear
INFLUX when finishing notification. For normal knote() it was fixed
in r310302 simply by remembering the fact that we do not own
KN_INFLUX, since there we own knlist lock and scan thread cannot clear
KN_INFLUX until we drop the lock. For knote_fork(), the situation is
more complicated, e must drop knlist lock AKA the process lock, since
we need to register new knotes.
Change KN_INFLUX into counter and allow shared ownership of the
in-flux state between scan and knote_fork() or knote(). Both in-flux
setters need to ensure that knote is not dropped in parallel. Added
assert about kn_influx == 1 in knote_drop() verifies that in-flux state
is not shared when knote is destroyed.
Since KBI of the struct knote is changed by addition of the int
kn_influx field, reorder kn_hook and kn_hookid to fill pad on LP64
arches [1]. This keeps sizeof(struct knote) to same 128 bytes as it
was before addition of kn_influx, on amd64.
Reviewed by: markj
Suggested by: markj [1]
Tested by: pho (previous version)
Sponsored by: The FreeBSD Foundation
Differential revision: https://reviews.freebsd.org/D8898
There are two instances of inlined unlocks + continue in vmtotal()
switch statements, which are ordinary expressed with break from the
switch case and code after the switch. Also, the combination of
continue and break statement is redundand.
Reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
accepting the wrong state and printing warning. Do not obliterate
kl_lock and kl_unlock pointers, they are often useful for post-mortem
analysis.
Reviewed by: markj
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
X-Differential revision: https://reviews.freebsd.org/D8898
There was report of stable/11 build failure on older versions of
FreeBSD. The problem was a reference to static variable in inline
function. Although fairly recent versions of clang can cope with this
situation just fine there is no strict requirement to make functions
in question inline, they're not in any time-critical codepath. So to
keep HEAD and 11-STABLE buildable on older FreeBSDs some of the util
functions were converted from inline to normal.
Reported by: hselasky
MFC after: 3 days
and host1x module. Unfortunately, tegra124 SoC doesn't have 2D acceleration
engine and 3D requires not yet started nouveau driver.
These drivers forms a first non-x86 DRM2 enabled graphic stack.
Note, there are 2 outstanding issues:
- The code uses gross hack in order to be comply with
OBJT_MGTDEVICE pager. (See tegra_bo_init_pager() in tegra_bo.c)
- Due to improper(probably) refcounting in drm_gem_mmap_single()
(in drm_gem.c), the gem objects are never released.
I hope that I will be able to address both issues in finite time,
but I don't want to touch x86 world now.
MFC after: 1 month
If system starts without attached monitor, DRM create framebuffer
for VT console. Later, when monitor is attached, the hotplug event must
issue full modeset procedure to setup CRTC.
In original code, this was done in drm_fb_helper_set_par(), but we don't
have this function implemented yet. Use unrolled version of
drm_fb_helper_set_par() to ensure same functionality.
MFC after: 1 month
Although vchiq_build_date and vchiq_build_time are not used in current
vchi driver at the moment, make sure these value will not leak into
build later on if at some point they will be refered in some new
imported code
PR: 215494
Reported by: emaste
MFC after: 1 week
There is no need to do two allocations per kqueue timer. Gather all
data needed by the timer callout into the structure and allocate it at
once.
Use the structure to preserve the result of timer2sbintime(), to not
perform repeated 64bit calculations in callout.
Remove tautological casts.
Remove now unused p_nexttime [1].
Noted by: markj [1]
Reviewed by: markj (previous version)
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
X-MFC note: do not remove p_nexttime
Differential revision: https://reviews.freebsd.org/D8901
the ones obtained through devclass_get_device(). Some minor code
cleanups while at it.
Obtained from: kmacy @
MFC after: 1 week
Sponsored by: Mellanox Technologies
In case of the empty queue tp->snd_holes and tcp_sackhole_insert()
failing due to memory shortage, tp->snd_holes will be empty.
This problem was hit when stress tests where performed by pho.
PR: 215513
Reported by: pho
Tested by: pho
Sponsored by: Netflix, Inc.
For EXTENDED COPY:
- improve parameters checking to report some errors before copy start;
- forward sense data from copy target as descriptor in case of error;
- report which CSCD reported error in sense key specific information.
For WRITE USING TOKEN:
- pass through real sense data from copy target instead of reporting
our copy error, since for initiator its a "simple" write, not a copy.
MFC after: 2 weeks
- Allow maximal sense size limitation via Control Extension mode page.
- When sense size limited, include descriptors atomically: whole or none.
- Set new SDAT_OVFL bit if some descriptors don't fit the limit.
- Report real written sense length instead of static maximal 252 bytes.
MFC after: 2 weeks
The count argument natural type if vm_pindex_t, but due to the loop
organization, it has to be signed type to detect the termination
condition. Replace this logic by using distinguished counter for the
processed pages, and terminate loop when the counter exceeds the
argument.
Completely process one swblock for all relevant indexes instead of
doing relookup in hash when incrementing page index on the loop step.
Do not drop hash mutex around iterations.
Noted and reviewed by: alc
Tested by: pho
Sponsored by: The FreeBSD Foundation
MFC after: 2 weeks
Return BUS_PROBE_NOWILDCARD in probe method to make sure that spigen
attaches only to the device created in identify method.
Before this change spigen probe method used to return 0 which meant it
competed with other drivers to be attached to the devices created for
child nodes of SPI bus node in FDT.
Reported by: Daniel Braniss
MFC after: 1 week
For most NFSv4.1 servers, a NFS4ERR_BAD_SESSION error is a rare failure
that indicates that the server has lost session/open/lock state.
However, recent testing by cperciva@ against the AmazonEFS server found
several problems with client recovery from this due to it generating this
failure frequently.
Briefly, the problems fixed are:
- If all session slots were in use at the time of the failure, some processes
would continue to loop waiting for a slot on the old session forever.
- If an RPC that doesn't use open/lock state failed with NFS4ERR_BAD_SESSION,
it would fail the RPC/syscall instead of initiating recovery and then
looping to retry the RPC.
- If a successful reply to an RPC for an old session wasn't processed
until after a new session was created for a NFS4ERR_BAD_SESSION error,
it would erroneously update the new session and corrupt it.
- The use of the first element of the session list in the nfs mount
structure (which is always the current metadata session) was slightly
racey. With changes for the above problems it became more racey, so all
uses of this head pointer was wrapped with a NFSLOCKMNT()/NFSUNLOCKMNT().
- Although the kernel malloc() usually allocates more bytes than requested
and, as such, this wouldn't have caused problems, the allocation of a
session structure was 1 byte smaller than it should have been.
(Null termination byte for the string not included in byte count.)
There are probably still problems with a pNFS data server that fails
with NFS4ERR_BAD_SESSION, but I have no server that does this to test
against (the AmazonEFS server doesn't do pNFS), so I can't fix these yet.
Although this patch is fairly large, it should only affect the handling
of NFS4ERR_BAD_SESSION error replies from an NFSv4.1 server.
Thanks go to cperciva@ for the extension testing he did to help isolate/fix
these problems.
Reported by: cperciva
Tested by: cperciva
MFC after: 3 months
Differential Revision: https://reviews.freebsd.org/D8745
operations to the MD PCPU region. Change sysmap initialization to only
allocate KVA pages for CPUs that are actually present. As a minor
optimization, this also prevents false sharing between adjacent sysmap objects
since the pcpu struct is already cacheline-aligned.
While here, move pc_qmap_addr initialization for the BSP into
pmap_bootstrap(), which allows use of pmap_quick* functions during early boot.
Reviewed by: kib
MFC after: 2 weeks
Differential Revision: https://reviews.freebsd.org/D8833
It is not compat w/ the old timesync message format, which the message
type stays the same as the old timesync message.
MFC after: 1 week
Sponsored by: Microsoft
Kernel stack overflows in MIPS call panic() directly from an assembly
handler after storing the interrupted context's registers in a
trapframe. Rather than inferring the location of ra, sp, and pc from
the instruction stream, recognize the pc of a kernel stack overflow
and pull the registers from the trapframe.
Sponsored by: DARPA / AFRL
- Honor PG_NODUMP by not dumping pages with this flag set.
- Pat the watchdog during dumps to avoid a watchdog reset while writing
out a dump.
- Reformat the output during a dump to update every 10% done rather than
every 2MB dumped.
- Include UMA small pages and pages holding PV entries in minidumps.
Sponsored by: DARPA / AFRL
to recreate it from ${MAKEOBJDIRPREFIX} and ${SRC_BASE} and ${KERNCONF},
the latter being especially problematic when KERNCONF is set to the names
of multiple kernel configs.
I don't yet know which RX descriptor bits map to shortgi, long-gi,
short-preamble, long-preamble, STBC, LDPC, HT40, etc - so I can't
easily add those just yet.
There's apparently no per-frame RX RSSI information exposed so we
also just use the results from the previous calibration task.
This also tidies up how the per-mbuf RSSI is pushed into the frame -
now that it's attached to the mbuf via rx_stats, we don't have to
do any silly hijinx to get it out of the frame processing path.
Tested:
* RTL8712, 1x1 cut 3, STA mode
dump_avail[] is supposed to be a superset of phys_avail[] that
describes all of the memory ranges that should be included in a full
dump. minidumps don't consider pages described by dump_avail[] to be
valid and thus they are excluded via the is_dumpable() function. Most
MIPS platforms (including MALTA) set dump_avail[] to be identical to
phys_avail[]. In particular, phys_avail[] doesn't include the kernel
itself, so pages for the kernel and it's global variables are not
considered dumpable and not included in the dump. Fix this by setting
dump_avail[0] to the first memory address (0) rather than the end of
the kernel.
Several other MIPS platforms have the same bug, though I am only able
to test malta in qemu. The correct fix is to set dump_avail[] to
describe RAM and in particular to not set dump_avail[0] to the end of
the kernel (kernel_kseg0_end).
Sponsored by: DARPA / AFRL
The removal of TAILQ_FOREACH_SAFE introduced a small race: when the last
thread on a sleepqueue is awoken, it reclaims the sleepqueue and may begin
executing on a different CPU before sleepq_resume_thread() returns. This
leaves a window during which it may go back to sleep and incorrectly be
awoken again by the caller of sleepq_broadcast().
Reported and tested by: pho
MFC after: 3 days
Sponsored by: Dell EMC Isilon
Current Xen IPI setup functions require that the caller provide a device in
order to obtain the name of the interrupt from it. With early AP startup this
device is no longer available at the point where IPIs are bound, and a KASSERT
would trigger:
panic: NULL pcpu device_t
cpuid = 0
KDB: stack backtrace:
db_trace_self_wrapper() at db_trace_self_wrapper+0x2b/frame 0xffffffff82233a20
vpanic() at vpanic+0x186/frame 0xffffffff82233aa0
kassert_panic() at kassert_panic+0x126/frame 0xffffffff82233b10
xen_setup_cpus() at xen_setup_cpus+0x5b/frame 0xffffffff82233b50
mi_startup() at mi_startup+0x118/frame 0xffffffff82233b70
btext() at btext+0x2c
Fix this by no longer requiring the presence of a device in order to bind IPIs,
and simply use the "cpuX" format where X is the CPU identifier in order to
describe the interrupt.
Reported by: sbruno, cperciva
Tested by: sbruno
X-MFC-With: r310177
Sponsored by: Citrix Systems R&D
