pci_remap_msix() can be used to alter the mapping of allocated
MSI-X vectors to the MSI-X table. The code had an off by one error
when adding the IRQ resources after performing a remap. This was
fatal for any vectors in the table that used the "last" valid IRQ as
those vectors were assigned a garbage IRQ value.
MFC after: 3 days
* Break out the 'g' phy code;
* Break out the debugging bits into a separate source file, since
some debugging prints are done in the phy code;
* Make some more chip methods in if_bwn.c public.
This brings the size of if_bwn.c down to 6,805 lines which is now
approaching managable.
This (and eventually migrating the other PHY code out) is in preparation
for adding the 11n PHY. No, the 11ac PHY (for the BCM4260 softmac part) isn't
yet open source, so we can't grow that. Yet.
This trims ~3,700 lines of code from if_bwn.c, bringing it down to a slightly
less crazy sounding 10,446 lines of code.
This patch adds support for restoring backlight after resume and adds models
Macbook3,1
MacbookAir5,1
MacbookAir5,2
It also incorporates fixes for bug #175260, bug #203610 and bug #203512
so those can be closed if this patch is applied.
PR: kern/209156
PR: kern/175260
PR: kern/203610
PR: kern/203512
Submitted by: Johannes Lundberg <johannes@brilliantservice.co.jp>
Implement several small improvements to the suspend/resume Xen sequence:
- Call the power_suspend_early event before stopping all processes.
- Stop all processes. This was done implicitly previously by putting all
the CPUs in a known IPI handler.
- Warm up the timecounter.
- Re-initialize the time of day register.
Sponsored by: Citrix Systems R&D
bus_get_cpus() returns a specified set of CPUs for a device. It accepts
an enum for the second parameter that indicates the type of cpuset to
request. Currently two valus are supported:
- LOCAL_CPUS (on x86 this returns all the CPUs in the package closest to
the device when DEVICE_NUMA is enabled)
- INTR_CPUS (like LOCAL_CPUS but only returns 1 SMT thread for each core)
For systems that do not support NUMA (or if it is not enabled in the kernel
config), LOCAL_CPUS fails with EINVAL. INTR_CPUS is mapped to 'all_cpus'
by default. The idea is that INTR_CPUS should always return a valid set.
Device drivers which want to use per-CPU interrupts should start using
INTR_CPUS instead of simply assigning interrupts to all available CPUs.
In the future we may wish to add tunables to control the policy of
INTR_CPUS (e.g. should it be local-only or global, should it ignore
SMT threads or not).
The x86 nexus driver exposes the internal set of interrupt CPUs from the
the x86 interrupt code via INTR_CPUS.
The ACPI bus driver and PCI bridge drivers use _PXM to return a suitable
LOCAL_CPUS set when _PXM exists and DEVICE_NUMA is enabled. They also and
the global INTR_CPUS set from the nexus driver with the per-domain set from
_PXM to generate a local INTR_CPUS set for child devices.
Reviewed by: wblock (manpage)
Differential Revision: https://reviews.freebsd.org/D5519
The current resolution of the Xen PV clock is too high, which causes an
adjustment of 5s to be applied to it. Reduce the resolution to be the same
as the RTC plus one, so it's always selected as the best source when
available on x86.
Also don't reset the clock on resume, it's pointless and discards any
previous adjustments.
Sponsoted by: Citrix Systems R&D
Dom0 should be able to set the host time. This is implemented by first
writing to the RTC (as would be done on bare metal), and then using the
XENPF_settime64 hypercall in order to force Xen to update the wallclock
shared page of all domains.
Sponsored by: Citrix Systems R&D
With the removal of the usage of the VCPU_SSHOTTMR_future flag, now
all errors from xentimer_vcpu_start_timer should be considered fatal, and
the loop is no longer needed since in case of setting the timer in the past
we will get an event interrupt right away (instead of returning ETIME).
Sponsored by: Citrix Systems R&D
MFC after : 2 weeks
On slow platforms with unreliable TSC, such as QEMU emulated machines,
it is possible for the FreeBSD kernel to request the next event in the
past. In that case, in the current implementation of
xentimer_vcpu_start_timer, we simply return -ETIME. To be precise Xen
returns -ETIME and we pass it on. As a consequence we need to loop
around to function to make sure that the timer is properly set.
Instead it is better to always ask the hypervisor for a timer event,
even if the timeout is past. To do that, remove the VCPU_SSHOTTMR_future
flag.
Submitted by: Stefano Stabellini <sstabellini@kernel.org>
Reviewed by: royger
MFC after: 2 weeks
* break out the operating mode and rx filter into new functions, rather
than them being hard-coded
* if we're in sniffer mode or not associated, set the BSS MAC to all zero,
rather than relying on a chip reset to do it for us
* add comments about .. how interestingly buggy the chip is.
Tested:
* AR9170 + AR9102, STA+monitor mode
Obtained from: linux carl9170 (general chip workings, constant definitions)
Switch to add_channel / add_channel_ht40 + pass channel's TX power
for the last.
Tested by: dhw
Reviewed by: adrian
Differential Revision: https://reviews.freebsd.org/D6141
driver is (or behaves identically to) /dev/mem. Remove the D_MEM flag
from random drivers.
Note that currently the D_MEM flag does not affect any behaviour, but
this going to change in the next commit.
Noted and reviewed by: alc
Sponsored by: The FreeBSD Foundation
MFC after: 1 week
X-Differential revision: https://reviews.freebsd.org/D6149
The Linux driver sets the rate_n_flags regardless of whether it's being
sent using firmware rate control or local rate control. This includes
the antenna configuration.
Thanks to Kyle Evans <kevans91@ksu.edu> for pointing this out to me
and doing some investigation/testing on his end.
Tested:
* Intel 7260 STA, 2G and 5G networks
I .. can't believe I missed this.
This showed up because the AP was TX'ing LDPC to an iwm(4) chipset,
which didn't advertise LDPC and doesn't /accept/ LDPC. Amusingly, all
the two other FreeBSD 11n parts I had tested with (AR9380, Intel 7260)
and I completely forgot to test on ye olde hardware.
That'll teach me.
Tested:
* AR9580 (AP) - Intel 7260 (STA), AR9380 (STA), Intel 6205 (STA)
function to error out early when no port module is present and doing
eeprom access. This also prevents error codes from filling up in
dmesg.
Sponsored by: Mellanox Technologies
Tested by: Netflix
MFC after: 1 week
LDPC adds better transmit reliability if both ends support it.
You in theory can do both STBC and LDPC at the same time.
If I see issues I'll disable it.
* Only enable it if both ends of a connection negotiate it.
* Disable it if any rate is non-11n.
* Count both LDPC TX and STBC TX.
Tested:
* AR9380, STA mode
Arguably we should only be doing the probe/attach to children of
these devices as well.
Tested by: Michal Stanek <mst_semihalf.com> (arm64)
Differential Revision: https://reviews.freebsd.org/D6133
Add new function gpio_alloc_intr_resource(), which allows an allocation
of interrupt resource associated to given gpio pin. It also allows to
specify interrupt configuration.
Note: This functionality is dependent on INTRNG, and must be
implemented in each GPIO controller.
Labels are limitted by 32 on EF10. It is not sufficient on powerful hosts.
Since only one RxQ is running over each EvQ, zero label may be used.
Reviewed by: gnn
Sponsored by: Solarflare Communications, Inc.
MFC after: 2 days
PR: 208267
Differential Revision: https://reviews.freebsd.org/D6121
