Figure out if the chip is counting PAUSE frames in the "normal" stats
and take them out if it is. This fixes a bug in the tx stats because
the default hardware behavior is different for Tx and Rx but the driver
was treating both the same way. The result was that OPACKETS, OBYTES,
and OMCASTS were under-reported (if tx_pause > 0) before this change.
Note that the mac_stats sysctl still gives you the raw value of these
statistics straight from the device registers.
defined:
sys/dev/cxgbe/t4_main.c:7474: warning: 'sysctl_tp_tick' defined but not used
sys/dev/cxgbe/t4_main.c:7505: warning: 'sysctl_tp_dack_timer' defined but not used
sys/dev/cxgbe/t4_main.c:7519: warning: 'sysctl_tp_timer' defined but not used
This just adds a bunch of #ifdef TCP_OFFLOAD in the right places.
Reviewed by: np
Differential Revision: https://reviews.freebsd.org/D5620
- Query the location of the log very early during attach. Refresh the
location later after establishing contact with the firmware.
- Save the log's location as a flat address in devlog_params.
- Use a memory window instead of backdoor access to the EDC/MC to read
the log.
which is responsible for filtering and RSS.
Add the ability to use filters that match on PF/VF (aka "VNIC id") while
here. This is mutually exclusive with filtering on outer VLAN tag with
Q-in-Q.
Sponsored by: Chelsio Communications
Move the code that reads all the parameters to t4_init_sge_params in the
shared code. Use these per-adapter values instead of globals.
Sponsored by: Chelsio Communications
- Get the list of registers to read during a regdump from the shared
code instead of the OS specific code. This follows a similar move
internally. The shared code includes the list for T6.
- Update cxgbetool to be able to decode T5 VF, T6, and T6 VF register
dumps (and catch up with some updates to T4 and T5 register decode).
Obtained from: Chelsio Communications
Sponsored by: Chelsio Communications
update to the latest internal shared code.
- Add a chip_params structure to keep track of hardware constants for
all generations of Terminators handled by cxgbe.
- Update t4_hw_pci_read_cfg4 to work with T6.
- Update the hardware debug sysctls (hidden within dev.<tNnex>.<n>.misc.*) to
work with T6. Most of the changes are in the decoders for the CIM
logic analyzer and the MPS TCAM.
- Acquire the regwin lock around indirect register accesses.
Obtained from: Chelsio Communications
Sponsored by: Chelsio Communications
code:
- Rename some CamelCase variables.
- s/t4_link_start/t4_link_l1cfg/g
- Pull in t4_get_port_type_description.
- Move t4_wait_op_done to t4_hw.c.
- Flip the order of the RDMA stats.
- Remove unsused function t4_iq_start_stop.
- Move t4_wait_op_done and t4_wait_op_done_val to t4_hw.c
Obtained from: Chelsio Communications
Each virtual interface has its own MAC address, queues, and statistics.
The dedicated netmap interfaces (ncxgbeX / ncxlX) were already implemented
as additional VIs on each port. This change allows additional non-netmap
interfaces to be configured on each port. Additional virtual interfaces
use the naming scheme vcxgbeX or vcxlX.
Additional VIs are enabled by setting the hw.cxgbe.num_vis tunable to a
value greater than 1 before loading the cxgbe(4) or cxl(4) driver.
NB: The first VI on each port is the "main" interface (cxgbeX or cxlX).
T4/T5 NICs provide a limited number of MAC addresses for each physical port.
As a result, a maximum of six VIs can be configured on each port (including
the "main" interface and the netmap interface when netmap is enabled).
One user-visible result is that when netmap is enabled, packets received
or transmitted via the netmap interface are no longer counted in the stats
for the "main" interface, but are not accounted to the netmap interface.
The netmap interfaces now also have a new-bus device and export various
information sysctl nodes via dev.n(cxgbe|cxl).X.
The cxgbetool 'clearstats' command clears the stats for all VIs on the
specified port along with the port's stats. There is currently no way to
clear the stats of an individual VI.
Reviewed by: np
MFC after: 1 month
Sponsored by: Chelsio
attributes when replying to a TLP from a Root Port. As a workaround,
disable No Snoop and Relaxed Ordering in the Root Port of each T5 adapter
during attach so that CPU-initiated requests do not contain these flags.
Note that this affects CPU-initiated requests to all devices under this
root port.
Reviewed by: np
MFC after: 1 week
Sponsored by: Chelsio
This commit contains large contributions from Giuseppe Lettieri and
Stefano Garzarella, is partly supported by grants from Verisign and Cisco,
and brings in the following:
- fix zerocopy monitor ports and introduce copying monitor ports
(the latter are lower performance but give access to all traffic
in parallel with the application)
- exclusive open mode, useful to implement solutions that recover
from crashes of the main netmap client (suggested by Patrick Kelsey)
- revised memory allocator in preparation for the 'passthrough mode'
(ptnetmap) recently presented at bsdcan. ptnetmap is described in
S. Garzarella, G. Lettieri, L. Rizzo;
Virtual device passthrough for high speed VM networking,
ACM/IEEE ANCS 2015, Oakland (CA) May 2015
http://info.iet.unipi.it/~luigi/research.html
- fix rx CRC handing on ixl
- add module dependencies for netmap when building drivers as modules
- minor simplifications to device-specific routines (*txsync, *rxsync)
- general code cleanup (remove unused variables, introduce macros
to access rings and remove duplicate code,
Applications do not need to be recompiled, unless of course
they want to use the new features (monitors and exclusive open).
Those willing to try this code on stable/10 can just update the
sys/dev/netmap/*, sys/net/netmap* with the version in HEAD
and apply the small patches to individual device drivers.
MFC after: 1 month
Sponsored by: (partly) Verisign, Cisco
years for head. However, it is continuously misused as the mpsafe argument
for callout_init(9). Deprecate the flag and clean up callout_init() calls
to make them more consistent.
Differential Revision: https://reviews.freebsd.org/D2613
Reviewed by: jhb
MFC after: 2 weeks
strings returned to userland include the nulterm byte.
Some uses of sbuf_new_for_sysctl() write binary data rather than strings;
clear the SBUF_INCLUDENUL flag after calling sbuf_new_for_sysctl() in
those cases. (Note that the sbuf code still automatically adds a nulterm
byte in sbuf_finish(), but since it's not included in the length it won't
get copied to userland along with the binary data.)
Remove explicit adding of a nulterm byte in a couple places now that it
gets done automatically by the sbuf drain code.
PR: 195668
Drivers (ULDs) and the base if_cxgbe driver.
Track the per-adapter activation of ULDs in a new "active_ulds" field.
This was done pretty arbitrarily before this change -- via TOM_INIT_DONE
in adapter->flags for TOM, and the (1 << MAX_NPORTS) bit in
adapter->offload_map for iWARP.
iWARP and hw-accelerated iSCSI rely on the TOE (supported by the TOM
ULD). The rules are:
a) If the iWARP and/or iSCSI ULDs are available when TOE is enabled then
iWARP and/or iSCSI are enabled too.
b) When the iWARP and iSCSI modules are loaded they go looking for
adapters with TOE enabled and enable themselves on that adapter.
c) You cannot deactivate or unload the TOM module from underneath iWARP
or iSCSI. Any such attempt will fail with EBUSY.
MFC after: 2 weeks
