We now pay attention to the maxio field in the XPT_PATH_INQ CCB,
and if it is set, propagate it up to physio via the si_iosize_max
field in the cdev structure.
We also now pay attention to the PIM_UNMAPPED capability bit in the
XPT_PATH_INQ CCB, and set the new SI_UNMAPPED cdev flag when the
underlying SIM supports unmapped I/O.
scsi_sa.c: Add unmapped I/O support and propagate the SIM's
maximum I/O size up.
Adjust scsi_tape_read_write() in the same way that
scsi_read_write() was changed to support unmapped
I/O. We overload the readop parameter with bits
that tell us whether it's an unmapped I/O, and we
need to set the CAM_DATA_BIO CCB flag. This change
should be backwards compatible in source and
binary forms.
MFC after: 1 week
Sponsored by: Spectra Logic
Change CCB queue resize logic to be able safely handle overallocations:
- (re)allocate queue space in power of 2 chunks with 64 elements minimum
and never shrink it; with only 4/8 bytes per element size is insignificant.
- automatically reallocate the queue to double size if it is overflowed.
- if queue reallocation failed, store extra CCBs in unsorted TAILQ,
fetching them back as soon as some queue element is freed.
To free space in CCB for TAILQ linking, change highpowerq from keeping
high-power CCBs to keeping devices frozen due to high-power CCBs.
This encloses all pieces of queue resize logic inside of cam_queue.[ch],
removing some not obvious duties from xpt_release_ccb().
While these operations are not really needed otherwise, at least for SCSI
they may cause extra errors if some other initiator holds write exclusive
reservation on the LUN (SYNCHRONIZE CACHE handled as "write" operation).
Add a PIM_NOSCAN flag to the CAM path inquiry CCB. This tells CAM
not to perform a rescan on a bus when it is registered.
We now use this flag in the mps(4) driver. Since it knows what
devices it has attached, it is more efficient for it to just issue
a target rescan on the targets that are attached.
Also, remove the private rescan thread from the mps(4) driver in
favor of the rescan thread already built into CAM. Without this
change, but with the change above, the MPS scanner could run before
or during CAM's initial setup, which would cause duplicate device
reprobes and announcements.
sys/param.h:
Bump __FreeBSD_version to 1000039 for the inclusion of the
PIM_RESCAN CAM path inquiry flag.
sys/cam/cam_ccb.h:
sys/cam/cam_xpt.c:
Added a PIM_NOSCAN flag. If a SIM sets this in the path
inquiry ccb, then CAM won't rescan the bus in
xpt_bus_regsister.
sys/dev/mps/mps_sas.c
For versions of FreeBSD that have the PIM_NOSCAN path
inquiry flag, don't freeze the sim queue during scanning,
because CAM won't be scanning this bus. Instead, hold
up the boot. Don't call mpssas_rescan_target in
mpssas_startup_decrement; it's redundant and I don't
know why it was in there.
Set PIM_NOSCAN in path inquiry CCBs.
Remove methods related to the internal rescan daemon.
Always use async events to trigger a probe for EEDP support.
In older versions of FreeBSD where AC_ADVINFO_CHANGED is
not available, use AC_FOUND_DEVICE and issue the
necessary READ CAPACITY manually.
Provide a path to xpt_register_async() so that we only
receive events for our own SCSI domain.
Improve error reporting in cases where setup for EEDP
detection fails.
sys/dev/mps/mps_sas.h:
Remove softc flags and data related to the scanner thread.
sys/dev/mps/mps_sas_lsi.c:
Unconditionally rescan the target whenever a device is added.
Sponsored by: Spectra Logic
MFC after: 1 week
"Logical unit not supported" errors. First initiates specific target rescan,
second -- destroys specific LUN. That allows to automatically detect changes
in list of device LUNs. This mechanism doesn't work when target is completely
idle, but probably that is all what can be done without active polling.
Reviewed by: ken
Sponsored by: iXsystems, Inc.
changers that don't support the DVCID and CURDATA bits that were
introduced in the SMC spec.
These changers will return an Illegal Request type error if the
bits are set. This causes "chio status" to fail.
The fix is two-fold. First, for changers that claim to be SCSI-2
or older, don't set the DVCID and CURDATA bits for READ ELEMENT
STATUS. For newer changers (SCSI-3 and newer), we default to
setting the new bits, but back off and try the READ ELEMENT STATUS
without the bits if we get an Illegal Request type error.
This has been tested on a Qualstar TLS-8211, which is a SCSI-2
changer that does not support the new bits, and a Spectra T-380,
which is a SCSI-3 changer that does support the new bits. In the
absence of a SCSI-3 changer that does not support the bits, I
tested that with some error injection code. (The SMC spec says
that support for CURDATA is mandatory, and DVCID is optional.)
scsi_ch.c: Add a new quirk, CH_Q_NO_DVCID that gets set for
SCSI-2 and older libraries, or newer libraries that
report errors when the DVCID/CURDATA bits are set.
In chgetelemstatus(), use the new quirk to
determine whether or not to set DVCID and CURDATA.
If we get an error with the bits set, back off and
try without the bits. Set the quirk flag if the
read element status succeeds without the bits set.
Increase the READ ELEMENT STATUS timeout to 60
seconds after testing with a Spectra T-380. The
previous value was 10 seconds, and too short for
the T-380. This may be decreased later after
some additional testing and investigation.
Tested by: Andre Albsmeier <Andre.Albsmeier@siemens.com>
Sponsored by: Spectra Logic
MFC after: 3 days
Ensure that d_delmaxsize is always set, removing init to 0 which could cause
future issues if use cases change.
Allow kern.cam.da.X.delete_max (which maps to d_delmaxsize) to be increased
up to the calculated max after being reduced.
MFC after: 1 day
X-MFC-With: r249940
needed for the last 10 years. Far too much of the internal API is
exposed, and every small adjustment causes applications to stop working.
To kick this off, bump the API version to 0x17 as should have been done
with r246713, but add shims to compensate. Thanks to the shims, there
should be no visible change in application behavior.
I have plans to do a significant overhaul of the API to harnen it for
the future, but until then, I welcome others to add shims for older
versions of the API.
Obtained from: Netflix
SPC-4 specification states that serial number may be property of device,
but not a specific logical unit. People reported about FC storages using
serial number in that way, making it unusable for purposes of LUN multipath
detection. SPC-4 states that designators associated with logical unit from
the VPD page 83h "Device Identification" should be used for that purpose.
Report first of them in the new attribute in such preference order: NAA,
EUI-64, T10 and SCSI name string.
While there, make GEOM DISK properly report GEOM::ident in XML output also
using d_getattr() method, if available. This fixes serial numbers reporting
for SCSI disks in `geom disk list` output and confxml.
Discussed with: gibbs, ken
Sponsored by: iXsystems, Inc.
MFC after: 2 weeks
While GEOM in general has provider opened while sending BIO_GETATTR,
GEOM DISK does not really need to open disk to read medium-unrelated
attributes for own use.
Proposed by: ken
Re-ordered SSD quirks alphabetically so they are easier to maintain.
Removed my email and PR reference from comments on each quirk.
Added quirks for more SSDs:
* Crucial M4
* Corsair Force GT
* Intel 520 Series
* Kingston E100 Series
* Samsung 830 Series
Reviewed by: pjd (mentor)
Approved by: pjd (mentor)
MFC after: 1 week
This prevents users from selecting a delete method which may cause
corruption e.g. MPS WS16 on pre P14 firmware.
Reviewed by: pjd (mentor)
Approved by: pjd (mentor)
MFC after: 2 days
With "cached read" HDD testing and multiple ports busy on a SATA
host controller, 3726/3826 PMP will very rarely drop a deferred
R_OK that was intended for the host. Symptom will be all 5 drives
under test will timeout, get reset, and recover.
Submitted by: Rich Futyma <rich.futyma@sanmina.com>
MFC after: 2 weeks
- remove DA_FLAG_SAW_MEDIA flag, almost opposite to DA_FLAG_PACK_INVALID,
using the last instead.
- allow opening device with no media present, reporting zero media size
and non-zero sector size, as geom/notes suggests. That allow to read
device attributes and potentially do other things, not related to media.
to query ATA functionality via ATA Pass-Through (16) as this page is defined
as "must" for SATL devices, hence indicating that the device is at least
likely to support Pass-Through (16).
This eliminates errors produced by CTL when ATA Pass-Through (16) fails.
Switch ATA probe daerror call to SF_NO_PRINT to avoid errors printing out
for devices which return invalid errors.
Output details about supported and choosen delete method when verbose booted.
Reviewed by: mav
Approved by: pjd (mentor)
MFC after: 1 week
