registers are control bits or depending on the model contain additional
time bits with a different meaning than the lower ones. In order to
only read the desired time bits and not change the upper bits on write
use appropriate masks in the gettime and settime function respectively.
Due to the polarity of the stop oscillator bit and the fact that the
century bits aren't used on sparc64 not masking them didn't cause
problems so far.
- Fix two off-by-one errors in the handling of the day of week. The
genclock code represents the dow as 0 - 6 with 0 being Sunday but the
mk48txx use 1 - 7 with 1 being Sunday. In the settime function when
writing the dow to the clock the range wasn't adjusted accordingly but
the clock apparently played along nicely otherwise the second bug in
the gettime function which mapped 1 - 7 to 0 - 6 but with 0 meaning
Saturday would have been triggered. Fixing these makes the date being
stored in the same format Sun/Solaris uses and cures the "Invalid time
in real time clock. Check and reset the date immediately!" when the
date was set under Solaris prior to booting FreeBSD/sparc64. [1]
Looking at other clock drivers/code e.g. FreeBSD/alpha the former "bug",
i.e. storing the dow as 0 - 6 even when the clock uses 1 - 7, seems to
be common but might be on purpose for compatibility when multi-booting
with other OS which do the same. So it might make sense to add a flag
to handle the dow off-by-one for use of this driver on platforms other
than sparc64.
- Check the state of the battery on mk48txx that support this in the
attach function.
- Add a note that use of the century bit should be implemented but isn't
required at the moment because it isn't used on sparc64.
Problem noted by: joerg [1]
MT5 candidate.
driver. Trim its fingernails by removing some useless bits before
fixing the 'thread not terminated on detach' problem.
o dmacnt is no longer used now that we allocate at attach time. Remove
it from struct fdc_data.
o ISPNP was only ever set, but never tested. It used to be used for the
allocation routines to change how it allocated resources. Since that's
no longer necessary, retire the flag.
o ISPCMICA was only ever tested, but never set. GC it. This removes
a special case in determining the drive type. The drive type is
now set in fdc_pcmcia.c, so the hack isn't needed anymore. Sadly,
this isn't tested with a Y-E Data pcmcia floppy drive because there
are a number of other issues that preclude it from working.
o Fix ifdef for reading from the rtc. I'm of the opinion that this ifdef
should be moved into fdc_isa.c, but not today as ideally there'd be
other fixes to the probing of children. So now we just read it on
i386 ! pc98 (there's no #define for MACHINE_ARCH, just MACHINE, hence
this slightly inelegant kludge) and amd64. The PC98 exclusion likely
isn't meaningful since pc98 uses a different driver, but will be when
merging of the pc98 floppy code into this driver is complete (this is the
other reason I think this block of code belongs outside fdc.c).
All of these changes are safe to MT5.
copper NICs, a link change event is posted whenever MII autopolling is
toggled off and on, which happens whenever someone calls
bge_miibus_readreg() or bge_miibus_writereg() to access the PHY
registers. This means anytime someone called the SIOCGIFMEDIA ioctl
on a bge interface, the link would reset. Even a simple "ifconfig bge0"
would do it, though other apps like dhclient or the PPPoE daemon could
trigger it as well. An obvious symptom of this problem is lots of
"bgeX: gigabit link up" messages appearing on the console for no
apparent reason.
Through experimentation, I determined that when a real link change
event occurs, the BGE_MIMODE_AUTOPOLL in the BGE_MI_MODE register
is always set, so now if we have a copper NIC and an link change
event occurs and the BGE_MIMODE_AUTOPOLL bit is clear, we ignore
the event.
Note that this does not apply to the original BCM5700 chip since we
use a different method for sensing link changes with that chip (the
status block method was broken), nor to fiber optic NICs since they
don't use the GMII PHY access registers.
another way to misinterpret the spec. Also, always fall back to the hints
probe on any attach failure, not just when _FDE fails.
Thanks to imp and scottl for finding this.
Tested by: rwatson (minimally)
MFC after: 5 days
After this change it should be possible to use very big md(4) devices.
- Clean up and simplify the code a bit.
- Use humanize_number(3) to print size of md(4) devices.
- Add 't' suffix which stands for terabyte.
- Make '-S' to really work with all types of devices.
- Other minor changes.
it is only used in one function. While doing so, change its type to
vm_ooffset_t.
We are still limited for swap-backed devices to 16TB on 32-bit architectures
where PAGE_SIZE is 4096 bytes.
This make "_NEC" devices appear as "NEC" which is more corrent.
The reason is tha NEC originally screwed up on the byteorder in the
model string, so now that they have realized that they prefixed the '_'
so that not every ATA driver on the planet would call them "EN C" :)
reserving it at use time is more miserly, low memory (< 16MB)
evaporates quickly on many systems, so there may not be any suitable
buffers available. This specifically doesn't use the newer, fancier
isa_dma_init to ease merging to 5.
Reviewed by: tegge, phk
the firmware status register on the card to see if the firmware is still
running. There is no way to recover from this, but at least it can give
a hint as whether the car has crashed (which happens all too often).
MFC after: 3 days
errors for the attachment process for the floppy controller. This is
a band-aide because it doesn't try any of the fallback methods when
_FDE isn't long enough, but should be sufficient for people
experiencing the dreaded mutex not initialized panic.
problems:
1) Add locking for SMP, code provided by Alan Cox
2) While testing Alan's patches, I observed serious problems with
the jumbo buffer allocation code (machine crashed twice), so I gutted
it and rewrote the receive handler to use multiple chained descriptors.
Each RX descriptor gets a single 2K cluster, and the chip will fill in
as many as it needs to hold the complete packet.
User reports that this corrects the data corruption issues previously
observed and discussed on -current.
Note that this driver still needs to be hit with the busdma stick.
I intend to inflict said beating in the near future.
MFC after: 1 week
o Allow for up to 3 resource I/O ranges to be given for the floppy
controller, rather than just two that are allowed for now.
o Make sure that we can work with either a base address of 0x3f0 or 0x3f2.
o Create new inline functions to access the YE DATA's unique BDCR register.
o Update pccard attachment to add the fd device.
o Do some minor style(9) polishing.
# I'm guessing that the fdc pccard attachment broke some time ago, since
# there are a number of issues with it still.
doesn't do this is beyond me, but that will be investigated later. This
results in programming the chip with the correct frequency, which in turn
allows devices to negotiate up to the full 20MB/s.
calls in sb_cmd2() and sb_getmixer(). The lock has already be grabbed
before these functions are called.
This is a RELENG_5 candidate.
PR: 71189
Submitted by: stephane
MFC after: 3 days
VT6122 gigabit ethernet chip and integrated 10/100/1000 copper PHY.
The vge driver has been added to GENERIC for i386, pc98 and amd64,
but not to sparc or ia64 since I don't have the ability to test
it there. The vge(4) driver supports VLANs, checksum offload and
jumbo frames.
Also added the lge(4) and nge(4) drivers to GENERIC for i386 and
pc98 since I was in the neighborhood. There's no reason to leave them
out anymore.
