a good job of it) in the copypktopts() function, just call ip6_clearpktopts()
directly. Otherwise, the callers of this function would end up freeing the
memory twice.
Reviewed by: jinmei
PR: kern/116360
o Acer Aspire 4520 laptop
- jack sensing / automute
o Toshiba Satellite A135-S4527 laptop
- jack sensing / automute
Tested by: lioux
o Apple Macbook 3 (is it?)
- require gpio0 (for speakers) and ovref50 (for headphone)
to make it works
- jack sensing / automute
Tested by: Ed Schouten
* Add Nvidia MCP67 controller ids.
* Be sensible about simmilar controller with multiple pci ids.
* Connect unused DAC/ADC to stream#0 rather than forcing each of them
managing their own stream.
MFC after: 3 days
include the ithread scheduling step. Without this, a preemption might
occur in between the interrupt getting masked and the ithread getting
scheduled. Since the interrupt handler runs in the context of curthread,
the scheudler might see it as having a such a low priority on a busy system
that it doesn't get to run for a _long_ time, leaving the interrupt stranded
in a disabled state. The only way that the preemption can happen is by
a fast/filter handler triggering a schduling event earlier in the handler,
so this problem can only happen for cases where an interrupt is being
shared by both a fast/filter handler and an ithread handler. Unfortunately,
it seems to be common for this sharing to happen with network and USB
devices, for example. This fixes many of the mysterious TCP session
timeouts and NIC watchdogs that were being reported. Many thanks to Sam
Lefler for getting to the bottom of this problem.
Reviewed by: jhb, jeff, silby
Note that ULong in this code is actually defined as an unsigned integer across
all arches so that the gdtoa() function always processes 32 bit data
despite the unfortunate naming of "ULong".
- Bring HEAD up to the latest shared code
- Fix TSO problem using limited MSS and forwarding
- Dual lock implementation
- New device support
- For my ease, this code can compile in either 6.x or later
- brings this driver in sync with the 6.3
prepend a data mbuf in front of a header mbuf without moving the header
to the new mbuf, and (2) a possible alignment problem on architectures
with strict alignment as reported in kern/4184.
PR: kern/4184 (1)
addresses as the source of an AARP request. While this PR was submitted
in the context of work in OpenBSD to port netatalk (in 1997), I've
synchronized the code more to our ARP input routine, which had similar
requirements.
Submitted by: Denton Gentry
PR: kern/4184
MFC after: 1 week
only at address 0 which is supposed to be the only valid phy address
on Marvell PHY. The more correct solution would be masking PHY
address ranges allowable in PHY probe routine. Unfortunately,
FreeBSD has no way to retrict the PHY address ranges or to pass special
flags to PHY driver.
This change assumes that PHY hardwares attached to msk(4) would be
Marvell made 88E11xx PHY.
With this changes the phantom phys attached on 88E8036(Yukon FE)
should disappear.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
only 4KB SRAM.
o Rework setting Tx/Rx RAM buffer size. Give receiver 2/3 of memory
and round it down to the multiple of 1024. The RAM buffer size of
Yukon II should be multiple of 1024. This fixes bogus RAM buffer
configuration used in Yukon FE.
Reported by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
Tested by: Oleg Lomaka < oleg AT lomaka DOT org DOT ua >
timestamps in the initial SYN packet actually use them in the rest of the
connection. Unfortunately, during the 7.0 testing cycle users have already
found network devices that violate this constraint.
RFC 1323 states 'and may send a TSopt in other segments' rather than
'and MUST send', so we must allow it.
Discovered by: Rob Zietlow
Tracked down by: Kip Macy
PR: bin/118005
publicly available datasheet for Yukon II and don't know what
bug/workaround exist for the specific hardware revision. Also I don't
think the vendor will release hardware errata in near future.
The hardware feature lists were not used at all except setting water
mark registers. Since msk(4) should know exact chip model/revision
number to decide which hardware capability could be used the extra
feature lists were redundant.
o Enable jumbo frame support for EC Ultra and disable jumbo frame
for FE.
o Enable store and forward mode for standard MTU sized frame.
o Enable TSO for EC Ultra. However TSO/checksum offload is disabled
for jumbo frame case. Because EC Ultra can't use store and forward
mode for jumbo frame TSO/checksum offload is not available.
o Adjust Tx GMAC almost empty threshold value and add a jumbo frame
water mark. The maic value was obtained from Marvell's sk98lin
driver.
o Fix EC Ultra chip revision number.
libraries had not had their versions bumped relative to 6.3-REL but
had indeed been changed. We need to bump their version so they can be
properly added to the compat6x port:
libasn1.so.8 libgssapi.so.8 libhdb.so.8 libkadm5clnt.so.8
libkadm5srv.so.8 libkafs5.so.8 libkrb5.so.8 libobjc.so.2
MFC After: 1 day
doesn't use the default CFLAGS which contain -fno-strict-aliasing.
Until the code is cleaned up, just add -fno-strict-aliasing to the
CFLAGS of these for the tinderboxes' sake, allowing the rest of the
tree to have -Werror enabled again.
rwlocks in conjuction with callouts. The function does basically what
callout_init_mtx() alredy does with the difference of using a rwlock
as extra argument.
CALLOUT_SHAREDLOCK flag can be used, now, in order to acquire the lock only
in read mode when running the callout handler. It has no effects when used
in conjuction with mtx.
In order to implement this, underlying callout functions have been made
completely lock type-unaware, so accordingly with this, sysctl
debug.to_avg_mtxcalls is now changed in the generic
debug.to_avg_lockcalls.
Note: currently the allowed lock classes are mutexes and rwlocks because
callout handlers run in softclock swi, so they cannot sleep and they
cannot acquire sleepable locks like sx or lockmgr.
Requested by: kmacy, pjd, rwatson
Reviewed by: jhb
obstacle to enabling -Werror. I'll continue to work on cleaning up the
code so that we can keep this enabled.
If the tinderboxes would just use the default CFLAGS set in this file,
all would be fine and we'd be able to make use of -Werror.
