Mainly focus on files that use BSD 2-Clause license, however the tool I
was using misidentified many licenses so this was mostly a manual - error
prone - task.
The Software Package Data Exchange (SPDX) group provides a specification
to make it easier for automated tools to detect and summarize well known
opensource licenses. We are gradually adopting the specification, noting
that the tags are considered only advisory and do not, in any way,
superceed or replace the license texts.
except for setting it. Also remove count from aha and replace it with
optional.
Also add commented out pccard lines for all the old card drivers.
They have to be commented out until they are converted because it
causes problems in NEWCARD.
o Cut out the probed stuff. We no longer need it since newbus implicitly
checks for this (likely bt can be changed as well in this way).
o Add preliminary support for unload. Untested because aha doesn't yet
support identify and there are some interactions with PnP that I've
not yet worked out.
With this I can boot the AHA-1542CP FW F.0. All the aha resources
appear to be picked up via pnp now.
commands are outstanding. You'd think they'd just clear the IDLE bit,
but alas, no. Delay until all pending mailbox commands have completed
in aha_cmd to work around this.
Report sync rates correctly on Fast Adaptec cards. Clones may still be
reported incorrectly since there is no documenation on how they report
extended sync values.
Clean up some unused fields in the aha softc.
pnp system in freebsd, I'm not sure how useful this will be, but my
1542CP seems to work well in plug and play mode and does seem to
probe correctly at all the oddball addresses/irq/drqs that I tried.
[[
I was unable to get /kernel.conf or /kernel.config to read in, so
I wasn't able to verify that this method of userconfig works. that's
one thing that makes pnp so hard to use in the current scheme.
Pointers to the right new way of doing this accepted.
]]
o Add some kludges to maybe bring support for 1540A/1542A into the
driver. Since I have no 154xA cards, and the only person I know
that has them hasn't given me feedback, I'm making this commit
blind.
o Honor unit numbers that are in the config file now. This allows one
to hard wire the unit numbers (and have high unit numbers for plug
and pray devices, which can't seem to be hardwired) and have the
cards not migrate from aha1 -> aha0 should aha0 go on the fritz. I
didn't verify that hard wired scsi busses would work, but did verify
that hard wired aha addresses did work to a limited extent. Both
aha0 and aha1 must be hardwired, or when the card that was in aha0
goes away, the probe for aha0 might pick up the card that otherwise
would have been aha1.
Convert from BT'isms to AHA'isms
Don't fail the probe if the illegal command bit is set in the status
register. If the BusLogic MultiMaster probe preceeded us, it may well
have determined that the card we are attaching to was not a true MultiMaster
by sending us a command that fails on the 154X.
Reset the adapter before doing the inquiry. This provides extra sanity
and will also clear the illegal command status bit that my be left over
from the MultiMaster probe.
o Use the board id command to find out what kind of board
we're talking to. If we're talking to a board that is has
an ID that is shared between boards supported by the aha
driver and the bt driver, then use the bt's geometry
register to weed out the bt cards. Otherwise assume that we
support this card.
o Remove bt esetup command sending to the card. It seems to
wedge too many cards.
o Revert to doing a soft reset after an invalid command. This
change didn't fix anything, so I'm backing it out. The
whole issue of card resetting needs to be revisisted at some
point so that we can do it properly on all hardware.
o GC unused stuff in some places.
