- Add proper scanning support rather than letting the firmware grab the first
access point
- Overhaul state changes
- Use macros for locking and provide _locked() versions of some functions
- Increase debugging output
- Use a callout rather than the old watchdog interface
- Improve style, function names and defines
- Add WPA (TKIP) support
Based heavily on a patchset provided by Sam Leffler.
VR_STICKHW register would result in unexpected results on these
hardwares. wpaul said the following for the issue.
The vr_attach() routine unconditionally does this for all supported
chips:
/*
* Windows may put the chip in suspend mode when it
* shuts down. Be sure to kick it in the head to wake it
* up again.
*/
VR_CLRBIT(sc, VR_STICKHW, (VR_STICKHW_DS0|VR_STICKHW_DS1));
The problem is, the VR_STICKHW register is not valid on all Rhine
devices. The VT86C100A chip, which is present on the D-Link DFE-530TX
boards, doesn't support power management, and its register space is
only 128 bytes wide. The VR_STICKHW register offset falls outside this
range. This may go unnoticed in most scenarios, but if you happen to have
another PCI device in your system which is assigned the register
space immediately after that of the Rhine, the vr(4) driver will
incorrectly stomp it. In my case, the BIOS on my test board decided
to put the register space for my PRO/100 ethernet board right next
to the Rhine, and the Rhine driver ended up clobbering the IMR register
of the PRO/100 device. (Long story short: the board kept locking up on
boot. Took me the better part of the morning suss out why.)
The strictly correct thing to do would be to check the PCI config space
to make sure the device supports the power management capability and only
write to the VR_STICKHW register if it does.
Instead of inspecting chip revision numbers for the availability of
VR_STICKHW register, check the existence of power management capability
of the hardware as wpaul suggested.
Reported by: wpaul
Suggested by: wpaul
OK'ed by: jhb
1. The locking was changed to shared but roundrobin mode still updated a
pointer in the softc with the next tx interface to use. This will panic
under high load. Change this to an atomically incremented sequence number in
order to choose the tx port in round robin.
2. IFQ_HANDOFF will free the mbuf if the queue is full, this will then be freed
again by lagg_start() and panic. Reorganised the error handling and freeing
to fix this.
MFC after: 3 days
SAS-enabled cards. It also makes the driver MPSAFE, eliminating some
problems that resulted from CAM becoming MPSAFE. Many thanks to 3Ware/AMCC
for continuing to support FreeBSD.
Submitted by: Manjunath Ranganathaiah
Approved by: re
voltage of 0. This can result in a divide by zero trap. Add a guard
for this case. The value of lfcap is checked in acpi_battery_bif_valid()
just before this, so it is safe.
Reportd by: sam
Approved by: re
MFC after: 3 days
of directly from acpi0. Before it would attach prior to the sysresource
devices, causing the later allocation of its memory range to fail and
print a warning like "acpi0: reservation of fed00000, 1000 (3) failed".
Use an explicit define for our probe order base value of 10.
Help from: jhb
Tested by: Abdullah Ibn Hamad Al-Marri <almarrie / gmail.com>
MFC after: 3 days
Approved by: re
fixes a bug on UP machines with SMP kernels where the idle thread
constantly switches after trying to steal work from the local cpu.
- Make the idle stealing code more robust against self selection.
- Prefer to steal from the cpu with the highest load that has at least one
transferable thread. Before we selected the cpu with the highest
transferable count which excludes bound threads.
Collaborated with: csjp
Approved by: re
to simply switch rather than lowering priority and switching. This allows
threads of equal priority to run but not lesser priority.
Discussed with: davidxu
Reported by: NIIMI Satoshi <sa2c@sa2c.net>
Approved by: re
critical_exit() owepreempt check. ULE will always use owepreempt to
preempt the idle thread. This change does not effect 4BSD since it will
never set owepreempt without PREEMPTION enabled.
- Remove some unused code from choosethread().
Discussed with: jhb
Approved by: re
it must first ensure that the page is no longer mapped. This is
trivially accomplished by calling pmap_remove_all() a little earlier
in vm_page_cache(). While I'm in the neighborbood, make a related
panic message a little more useful.
Approved by: re (kensmith)
Reported by: Peter Holm and Konstantin Belousov
Reviewed by: Konstantin Belousov
a consequence of sparc64/sparc64/vm_machdep.c revision 1.76. It occurs
when uma_small_free() frees a page. The solution has two parts: (1) Mark
pages allocated with VM_ALLOC_NOOBJ as PG_UNMANAGED. (2) Defer the lock
assertion in pmap_page_is_mapped() until after PG_UNMANAGED is tested.
This is safe because both PG_UNMANAGED and PG_FICTITIOUS are immutable
flags, i.e., they do not change state between the time that a page is
allocated and freed.
Approved by: re (kensmith)
PR: 116794
TCP: [X.X.X.X]:X to [X.X.X.X]:X tcpflags 0x18<PUSH,ACK>; tcp_do_segment: FIN_WAIT_2: Received data after socket was closed, sending RST and removing tcpcb
So that it also includes how many bytes of data were received. It now looks
like this:
TCP: [X.X.X.X]:X to [X.X.X.X]:X tcpflags 0x18<PUSH,ACK>; tcp_do_segment: FIN_WAIT_2: Received X bytes of data after socket was closed, sending RST and removing tcpcb
Approved by: re (gnn)
not being independently freeable. This allows one to embed an mbuf in
the cluster itself. This confers the benefits of the packet zone on
all cluster sizes. Embedded mbufs currently suffer from the same
limitation that packet zone mbufs do in that one cannot disconnect
them and pass them around independently of the cluster. It would
likely be possible to eliminate this limitation in the future by
adding a second reference for the mbuf itself.
Approved by: re(gnn)
problems with the syncache, it produces a lot of console noise and has led
to quite a few false positive bug reports. It can be selectively
re-enabled when debugging specific problems by frobbing the same sysctl.
Discussed with: silby
Approved by: re (gnn)
directory itself (rather than any of its contents) is visible to the
current thread.
MFC after: 1 week
PR: kern/90063
Submitted by: john of 8192.net
Approved by: re (kensmith)
with all functions supported. This is done adding usb device IDs
to the table of recognised devices (because there is no standard
'scanner' class, so no other way to recognise them), and with
a small change to the uscanner attach routine that prevents
reconfiguring the whole USB device while we are dealing only with
one of its USB interfaces.
The latter part has been suggested by Steinar Hamre in
http://www.freebsd.org/cgi/query-pr.cgi?pr=107665 , i have
only added a bit of explaination to the code.
I have personally tried this on the Epson DX-5050 and DX-6000
devices (on the US market they have different names, CX-something).
I have good reasons to think that, possibly with the mere addition
of more USB ids to the table in uscanner.c, this should work with
all Epson multifunction devices in that family (from DX-3800 to
DX-7000 - these units are in the 50-120$ price range).
More details on related topics (SANE configuration, OCR, etc.)
at http://info.iet.unipi.it/~luigi/FreeBSD/dx5050.html
Manpage updates coming soon.
Approved by: re, imp
MFC after: 3 days
UDMA modes.
Please notice that Soekris NET5501 bios versions before 1.32f has a bug
that prevents this from working.
Approved by: re (gnn)
MFC: 2 weeks
Before that fix, it was possible for the function to fail if number
of sharers changes between 'x = sx->sx_lock' step and atomic_cmpset_acq_ptr()
call.
This fixes ZFS problem when ZFS returns strange EIO errors under load.
In ZFS there is a code that depends on the fact that sx_try_slock() can
only fail if there is an exclusive owner.
Discussed with: attilio
Reviewed by: jhb
Approved by: re (kensmith)
after the switch leads to a race where the outgoing thread still owns
the local queue lock while another cpu may switch it in. This race
is only possible on machines where cpu_switch can take significantly
longer on different cpus which in practice means HTT machines with
unfair thread scheduling algorithms.
Found by: kris (of course)
Approved by: re
starvation caused by unbalanced interrupt loads.
- Change the rebalancer to work on stathz ticks but retain randomization.
- Simplify locking in tdq_idled() to use the tdq_lock_pair() rather than
complex sequences of locks to avoid deadlock.
Reported by: kris
Approved by: re
retransmittion by handover event (fast mobility code)
- Fixed problem of mobility code which is caused by remaining
parameters in the deleted primary destination.
- Add a missing lock. When a peer sends an INIT, and while we
are processing it to send an INIT-ACK the socket is closed,
we did not hold a lock to keep the socket from going away.
Add protection for this case.
- Fix so that arwnd is alway uses the minimal rwnd if the user
has set the socket buffer smaller. Found this when the test
org decided to see what happens when you set in a rwnd of 10
bytes (which is not allowed per RFC .. 4k is minimum).
- Fixes so a cookie-echo ootb will NOT cause an abort to
be sent. This was happening in a MPI collision case.
- Examined all panics and unless there was no recovery, moved
any that were not already to INVARANTS.
Approved by: re@freebsd.org (gnn)
support machines having multiple independently numbered PCI domains
and don't support reenumeration without ambiguity amongst the
devices as seen by the OS and represented by PCI location strings.
This includes introducing a function pci_find_dbsf(9) which works
like pci_find_bsf(9) but additionally takes a domain number argument
and limiting pci_find_bsf(9) to only search devices in domain 0 (the
only domain in single-domain systems). Bge(4) and ofw_pcibus(4) are
changed to use pci_find_dbsf(9) instead of pci_find_bsf(9) in order
to no longer report false positives when searching for siblings and
dupe devices in the same domain respectively.
Along with this change the sole host-PCI bridge driver converted to
actually make use of PCI domain support is uninorth(4), the others
continue to use domain 0 only for now and need to be converted as
appropriate later on.
Note that this means that the format of the location strings as used
by pciconf(8) has been changed and that consumers of <sys/pciio.h>
potentially need to be recompiled.
Suggested by: jhb
Reviewed by: grehan, jhb, marcel
Approved by: re (kensmith), jhb (PCI maintainer hat)
After discussion with Sam, switch back to use firmware(9) instead of
having the firmware in hex format.
Put the binary firmware uuencoded into sys/contrib/dev/npe, and slap a
LICENSE file, as found on the Intel website.
Approved by: re (blanket), mux (mentor)
MFC After: 1 week
Without this change the following situation was possible:
1. Provider is orphaned from within class' access() method on last write
close - orphan provider event is send.
2. GEOM detects last write close on a provider and sends new provider event.
3. g_orphan_register() is called, and calls all orphan methods of attached
consumers.
4. New provider event is executed on orphaned provider, all classes can
taste already orphaned provider, and some may attach consumers to it.
Those consumers will never go away, because the g_orphan_register()
was already called.
We end up with a zombie provider.
With this change, at step 3, we will cancel new provider event.
How to repeat this problem:
# mdconfig -a -t malloc -s 10m
# geli init -i 0 md0
# geli attach md0
# newfs -L test /dev/md0.eli
# mount /dev/ufs/test /mnt/tmp
# geli detach -l md0.eli
# umount /mnt/tmp
# glabel status
Name Status Components
ufs/test N/A N/A
Reviewed by: phk
Approved by: re (kensmith)
value for kern.sched.preempt_thresh appropriately. It can still by
adjusted at runtime. ULE will still use IPI_PREEMPT in certain
migration situations.
- Assert that we're not trying to compile ULE on an unsupported
architecture. To date, I believe only i386 and amd64 have implemented
the third cpu switch argument required.
Approved by: re
cache: vm_object_page_remove() should convert any cached pages that
fall with the specified range to free pages. Otherwise, there could
be a problem if a file is first truncated and then regrown.
Specifically, some old data from prior to the truncation might reappear.
Generalize vm_page_cache_free() to support the conversion of either a
subset or the entirety of an object's cached pages.
Reported by: tegge
Reviewed by: tegge
Approved by: re (kensmith)
to gem_attach() as the former access softc members not yet initialized
at that time and gem_reset() actually is enough to stop the chip. [1]
o Revise the use of gem_bitwait(); add bus_barrier() calls before calling
gem_bitwait() to ensure the respective bit has been written before we
starting polling on it and poll for the right bits to change, f.e. even
though we only reset RX we have to actually wait for both GEM_RESET_RX
and GEM_RESET_TX to clear. Add some additional gem_bitwait() calls in
places we've been missing them according to the GEM documentation.
Along with this some excessive DELAYs, which probably only were added
because of bugs in gem_bitwait() and its use in the first place, as
well as as have of an gem_bitwait() reimplementation in gem_reset_tx()
were removed.
o Add gem_reset_rxdma() and use it to deal with GEM_MAC_RX_OVERFLOW errors
more gracefully as unlike gem_init_locked() it resets the RX DMA engine
only, causing no link loss and the FIFOs not to be cleared. Also use it
deal with GEM_INTR_RX_TAG_ERR errors, with previously were unhandled.
This was based on information obtained from the Linux GEM and OpenSolaris
ERI drivers.
o Turn on workarounds for silicon bugs in the Apple GMAC variants.
This was based on information obtained from the Darwin GMAC and Linux GEM
drivers.
o Turn on "infinite" (i.e. maximum 31 * 64 bytes in length) DMA bursts.
This greatly improves especially RX performance.
o Optimize the RX path, this consists of:
- kicking the receiver as soon as we've a spare descriptor in gem_rint()
again instead of just once after all the ready ones have been handled;
- kicking the receiver the right way, i.e. as outlined in the GEM
documentation in batches of 4 and by pointing it to the descriptor
after the last valid one;
- calling gem_rint() before gem_tint() in gem_intr() as gem_tint() may
take quite a while;
- doubling the size of the RX ring to 256 descriptors.
Overall the RX performance of a GEM in a 1GHz Sun Fire V210 was improved
from ~100Mbit/s to ~850Mbit/s.
o In gem_add_rxbuf() don't assign the newly allocated mbuf to rxs_mbuf
before calling bus_dmamap_load_mbuf_sg(), if bus_dmamap_load_mbuf_sg()
fails we'll free the newly allocated mbuf, unable to recycle the
previous one but a NULL pointer dereference instead.
o In gem_init_locked() honor the return value of gem_meminit().
o Simplify gem_ringsize() and dont' return garbage in the default case.
Based on OpenBSD.
o Don't turn on MAC control, MIF and PCS interrupts unless GEM_DEBUG is
defined as we don't need/use these interrupts for operation.
o In gem_start_locked() sync the DMA maps of the descriptor rings before
every kick of the transmitter and not just once after enqueuing all
packets as the NIC might instantly start transmitting after we kicked
it the first time.
o Keep state of the link state and use it to enable or disable the MAC
in gem_mii_statchg() accordingly as well as to return early from
gem_start_locked() in case the link is down. [3]
o Initialize the maximum frame size to a sane value.
o In gem_mii_statchg() enable carrier extension if appropriate.
o Increment if_ierrors in case of an GEM_MAC_RX_OVERFLOW error and in
gem_eint(). [3]
o Handle IFF_ALLMULTI correctly; don't set it if we've turned promiscuous
group mode on and don't clear the flag if we've disabled promiscuous
group mode (these were mostly NOPs though). [2]
o Let gem_eint() also report GEM_INTR_PERR errors.
o Move setting sc_variant from gem_pci_probe() to gem_pci_attach() as
device probe methods are not supposed to touch the softc.
o Collapse sc_inited and sc_pci into bits for sc_flags.
o Add CTASSERTs ensuring that GEM_NRXDESC and GEM_NTXDESC are set to
legal values.
o Correctly set up for 802.3x flow control, though #ifdef out the code
that actually enables it as this needs more testing and mainly a proper
framework to support it.
o Correct and add some conversions from hard-coded functions names to
__func__ which were borked or forgotten in if_gem.c rev. 1.42.
o Use PCIR_BAR instead of a homegrown macro.
o Replace sc_enaddr[6] with sc_enaddr[ETHER_ADDR_LEN].
o In gem_pci_attach() in case attaching fails release the resources in
the opposite order they were allocated.
o Make gem_reset() static to if_gem.c as it's not needed outside that
module.
o Remove the GEM_GIGABIT flag and the associated code; GEM_GIGABIT was
never set and the associated code was in the wrong place.
o Remove sc_mif_config; it was only used to cache the contents of the
respective register within gem_attach().
o Remove the #ifdef'ed out NetBSD/OpenBSD code for establishing a suspend
hook as it will never be used on FreeBSD.
o Also probe Apple Intrepid 2 GMAC and Apple Shasta GMAC, add support for
Apple K2 GMAC. Based on OpenBSD.
o Add support for Sun GBE/P cards, or in other words actually add support
for cards based on GEM to gem(4). This mainly consists of adding support
for the TBI of these chips. Along with this the PHY selection code was
rewritten to hardcode the PHY number for certain configurations as for
example the PHY of the on-board ERI of Blade 1000 shows up twice causing
no link as the second incarnation is isolated.
These changes were ported from OpenBSD with some additional improvements
and modulo some bugs.
o Add code to if_gem_pci.c allowing to read the MAC-address from the VPD on
systems without Open Firmware.
This is an improved version of my variant of the respective code in
if_hme_pci.c
o Now that gem(4) is MI enable it for all archs.
Pointed out by: yongari [1]
Suggested by: rwatson [2], yongari [3]
Tested on: i386 (GEM), powerpc (GMACs by marcel and yongari),
sparc64 (ERI and GEM)
Reviewed by: yongari
Approved by: re (kensmith)
33MHz for calculating the latency timer values for its children.
Inspired by NetBSD doing the same and Linux as well as OpenSolaris
using a similar approach.
While at it rename a variable and change its type to be more
appropriate fuer values of PCI properties so the variable can be
more easily reused.
- Initialize the cache line size register of PCI devices to a
legal value; the cache line size is limited to 64 bytes by the
Fireplane/Safari, JBus and UPA interconnection busses. Setting
it to an unsupported value caused bad performance at least with
GEM as it causes them to not do cache line bursts and to not
issue cache line commands on the PCI bus.
Approved by: re (kensmith)
MFC after: 1 week
timeout occurring at exactly the same time. If this happens, the nfsiod
exits although there may be a queued async IO request for it.
Found by : Kris Kennaway
Approved by: re
ways:
(1) Cached pages are no longer kept in the object's resident page
splay tree and memq. Instead, they are kept in a separate per-object
splay tree of cached pages. However, access to this new per-object
splay tree is synchronized by the _free_ page queues lock, not to be
confused with the heavily contended page queues lock. Consequently, a
cached page can be reclaimed by vm_page_alloc(9) without acquiring the
object's lock or the page queues lock.
This solves a problem independently reported by tegge@ and Isilon.
Specifically, they observed the page daemon consuming a great deal of
CPU time because of pages bouncing back and forth between the cache
queue (PQ_CACHE) and the inactive queue (PQ_INACTIVE). The source of
this problem turned out to be a deadlock avoidance strategy employed
when selecting a cached page to reclaim in vm_page_select_cache().
However, the root cause was really that reclaiming a cached page
required the acquisition of an object lock while the page queues lock
was already held. Thus, this change addresses the problem at its
root, by eliminating the need to acquire the object's lock.
Moreover, keeping cached pages in the object's primary splay tree and
memq was, in effect, optimizing for the uncommon case. Cached pages
are reclaimed far, far more often than they are reactivated. Instead,
this change makes reclamation cheaper, especially in terms of
synchronization overhead, and reactivation more expensive, because
reactivated pages will have to be reentered into the object's primary
splay tree and memq.
(2) Cached pages are now stored alongside free pages in the physical
memory allocator's buddy queues, increasing the likelihood that large
allocations of contiguous physical memory (i.e., superpages) will
succeed.
Finally, as a result of this change long-standing restrictions on when
and where a cached page can be reclaimed and returned by
vm_page_alloc(9) are eliminated. Specifically, calls to
vm_page_alloc(9) specifying VM_ALLOC_INTERRUPT can now reclaim and
return a formerly cached page. Consequently, a call to malloc(9)
specifying M_NOWAIT is less likely to fail.
Discussed with: many over the course of the summer, including jeff@,
Justin Husted @ Isilon, peter@, tegge@
Tested by: an earlier version by kris@
Approved by: re (kensmith)
This patch was part of ACPI-CA 20070508 release and the
following is excerpt from its change log:
Fixed a problem where the Global Lock handle was not properly
updated if a thread that acquired the Global Lock via executing
AML code then attempted to acquire the lock via the
AcpiAcquireGlobalLock interface. Reported by Joe Liu.
Approved by: re (kensmith)
Tested by: ambrisko
Obtained from: Intel
polling/interrupt-driven fallback and instead use polling only during
boot and pure interrupt-driven mode after boot. Polled mode could be
relegated completely to a legacy role if we could enable interrupts
during boot. Polled mode can be forced after boot by setting
debug.acpi.ec.polled="1", i.e. if there are timeouts.
- Use polling only during boot, shutdown, or if requested by the user.
Otherwise, use a generation count of GPEs, incremented atomically. This
prevents an old status value from being used if the EC is really slow
and the same condition (i.e. multiple IBEs for a write transaction) is
being checked.
- Check for and run the query handler directly if the SCI bit is set in
the status register during boot. Previously, the query handler wouldn't
run until interrupts were finally enabled late in boot.
- During boot and after starting a command, check if the event appears
to already have occurred before we even start waiting. If so, it's
possible the EC is very slow and we might accept an old status value.
Print a warning in this case. Once we've booted, interrupt-driven mode
should work just fine but polled mode could be unreliable. There's not
much more we can do about this until interrupts are enabled during boot.
- In the above case, we also do one final check if the interrupt-driven
mode gets a timeout. If the status is complete, it will force the
system back into polled mode since interrupt mode doesn't work. For
polled mode during boot, if the status appears to be already complete
before beginning the check loop, it waits 10 us before actually checking
the status, just in case the EC is really slow and hasn't gotten to work
on the new request yet.
- Use upper-case hex for the _Qxx method
- Use device_printf for errors, don't hide them under verbose
- Increase default total timeout to 750 ms and decrease polling interval
to 5 us.
- Don't pass the status value via the softc. Just read it directly.
- Remove the mutex. We use the sx lock for transaction serialization
with the query handler.
- Remove the Intel copyright notice as no code of theirs was ever
present in this file (verified against rev 1.1)
- Allow KTR module-only builds for ease of testing
Thanks to jkim and Alexey Starikovskiy for helpful discussions and testing.
Approved by: re
MFC after: 2 weeks
- Reintegrate the ANSI C function declaration change
from tcp_timer.c rev 1.92
- Reorganize the tcpcb structure so that it has a single
pointer to the "tcp_timer" structure which contains all
of the tcp timer callouts. This change means that when
the single tcp timer change is reintegrated, tcpcb will
not change in size, and therefore the ABI between
netstat and the kernel will not change.
Neither of these changes should have any functional
impact.
Reviewed by: bmah, rrs
Approved by: re (bmah)
route and once they are done with it, call rtfree(). rtfree() should
only be used when we are certain we hold the last reference to the
route. This bug results in console messages like the following:
rtfree: 0xc40f7000 has 1 refs
This patch switches the rtfree() to use RTFREE_LOCKED() instead,
which should handle the reference counting on the route better.
Approved by: re@ (gnn)
Reviewed by: bms
Reported by: many via net@ and current@
Tested by: many
All active fields in fsi are advisory/optional, so we shouldn't do
extra work to make them valid at all times, but instead we write to
the fsi too often (we still do), and we searched for a free cluster
for fsinxtfree too often.
This commit just removes the whole search and its results, so that we
write out our in-core copy of fsinxtfree instead of writing a "fixed"
copy and clobbering our in-core copy. This saves fixing 3 bugs:
- off-by-1 error for the end of the search, resulting in fsinxtfree
not actually being adjusted iff only the last cluster is free.
- missing adjustment when no clusters are free.
- off-by-many error for the start of the search. Starting the search
at 0 instead of at (the in-core copy of) fsinxtfree did more than
defeat the reasons for existence of fsinxtfree. fsinxtfree exists
mainly to avoid having to start at 0 for just the first search per
mount, but has the side effect of reducing bias towards allocating
near cluster 0. The bias would normally only be generated by the
first search per mount (if fsinxtfree is not supported), but since
we also adjusted the in-core copy of fsinxtfree here, we were doing
extra work to maximize the bias.
Approved by: re (kensmith)
providers with limited physical storage and add physical storage as
needed.
Submitted by: Ivan Voras
Sponsored by: Google Summer of Code 2006
Approved by: re (kensmith)
- Improve load long-term load balancer by always IPIing exactly once.
Previously the delay after rebalancing could cause problems with
uneven workloads.
- Allow nice to have a linear effect on the interactivity score. This
allows negatively niced programs to stay interactive longer. It may be
useful with very expensive Xorg servers under high loads. In general
it should not be necessary to alter the nice level to improve interactive
response. We may also want to consider never allowing positively niced
processes to become interactive at all.
- Initialize ccpu to 0 rather than 0.0. The decimal point was leftover
from when the code was copied from 4bsd. ccpu is 0 in ULE because ULE
only exports weighted cpu values.
Reported by: Steve Kargl (Load balancing problem)
Approved by: re
Eliminates panics due to locking issues.
Idea taken from src/sys/gnu/fs/xfs/FreeBSD/xfs_super.c.
PR: 89966, 92000, 104393
Reported by: H. Matsuo <hiroshi50000 yahoo co jp>,
Chris <m2chrischou gmail.com>,
Andrey V. Elsukov <bu7cher yandex ru>,
Jan Henrik Sylvester <me janh de>
Approved by: re (kensmith)
simplifies code and should speedup pppoe_findsession() function which is
called for every incoming packet.
Approved by: re (kensmith), glebius (mentor)
changes the units from seconds to the value of 'ticks' when swapped
in/out. ULE does not have a periodic timer that scans all threads in
the system and as such maintaining a per-second counter is difficult.
- Change computations requiring the unit in seconds to subtract ticks
and divide by hz. This does make the wraparound condition hz times
more frequent but this is still in the range of several months to
years and the adverse effects are minimal.
Approved by: re
last interface should own the address, but the current code
fumbles the handoff. This fixes that.
- move address related debugs to PCB4 and add additional ones to
help in debugging address problems.
Approved by: re@freebsd.org (K Smith)
changes the units from seconds to the value of 'ticks' when swapped
in/out. ULE does not have a periodic timer that scans all threads in
the system and as such maintaining a per-second counter is difficult.
- Change computations requiring the unit in seconds to subtract ticks
and divide by hz. This does make the wraparound condition hz times
more frequent but this is still in the range of several months to
years and the adverse effects are minimal.
Approved by: re
In particular:
- smp_tlb_mtx is no longer used, so it is axed.
- smp rendezvous lock isn't really a leaf spin-mutex. Its bad placement in
the table, however, has been the source of a false positive LOR reporting
with the dt_lock. However, smp rendezvous lock would have had sched_lock
there for older lock, so it wasn't still a leaf lock.
- allpmaps is only used in ia32 architecture, so it is inserted in the
appropriate stub.
Addictionally:
- kse_zombie_lock is no longer present, so its definition is axed out.
- zombie_lock doesn't need to have an exported symbol, so just let's it be
declared as static.
Tested by: kris
Approved by: jeff (mentor)
Approved by: re
Together with the sys/i386/i386/trap.c rev. 1.306 it fixes the PR.
Submitted by: rdivacky
Suggested by: jhb
Sponsored by: Google Summer of Code 2007
PR: kern/77710
Approved by: re (kensmith)
- The output routine of low level console is not protected by any lock
by default.
- Increment and decrement of sc->write_in_progress are not atomic and
this may cause console hang.
- We also have many other states used by emulator that should be protected
by the lock.
- This change does not fix interspersed messages which PRINTF_BUFR_SIZE
kernel option should fix.
Approved by: re (bmah)
MFC after: 1 week
commented out until I can re-test them on all our architectures. I
had re@ approval to commit this a long time ago, but that's before we
were this close to the branch.
Approved by: re@
controller if it's sole child device has the "usb" device class.
Previously ehci(4) would think that PCI-ISA bridges on the same slot
(such as in some Intel ICHs) were "neighbors" resulting in spurious
warnings about neighbor count mismatches.
- Fix a memory leak when looking for neighbors.
MFC after: 1 week
Approved by: re (kensmith)
Tested by: phk
to become unkillable when that process is sent a termination signal. The
process will sit in waitvt looping in the kernel, and chewing up all
available CPU until the system is rebooted.
Submitted by: Jilles Tjoelker <jilles@stack.nl>
Reviewed by: bde
Approved by: re (kensmith)
MFC after: 1 week
to the node before starting the work, otherwise the node may go
away before a reference is made in ieee80211_send_mgmt.
Approved by: re (blanket wireless)
Obtained from: Atheros
3 arguments, but we had forgotten the second argument. Also make the
Linux statfs64 struct depend on the architecture because it has an
extra 4 bytes padding on amd64 compared to i386.
The three argument fix is from David Taylor, the struct statfs64
stuff is my fault. With this patch I can install i386 Linux matlab
on an amd64 machine.
Submitted by: David Taylor <davidt_at_yadt.co.uk>
Approved by: re (kensmith)
the mfi(4) LSI MegaSAS RAID card. Looking at the Linux driver for the
mpt(4) it should be 0x0062 and not 0x0060. Tested with an mfi card
of this device id.
Approved by: re (bmah)
Reviewed by: scottl
MFC after: 3 days
also involves macro changes to have a RLOCK and a WLOCK
and placing the correct version within the code.
- The INP-INFO lock is changed to a rwlock.
- When sctp_shutdown() is called on Mac OS X, the socket lock is held.
So call sctp_chunk_output with SCTP_SO_LOCKED and
not SCTP_SO_NOT_LOCKED.
- Add SCTP_IPI_ADDR_[RW]LOCK and SCTP_IPI_ADDR_[RW]UNLOCK for Mac OS X.
- u_int64_t -> uint64_t
- add missing addr unlock for error return path
Approved by: re@freebsd.org (K Smith)
was used in assembler code in such a way that no unresolved relocation
records were generated, so ld didn't flag the problem. You can see
this with an 'nm' of the kernel. There will be 'U MAXCPU' on SMP systems.
The impact of this is that the intrcount/intrnames arrays do not have
the intended amount of space reserved. This could lead to interesting
problems due to the arrays being present in the middle of kernel code.
An overflow would be rather interesting as executable code would be used
as per-cpu incrementing interrupt counters.
This fixes it for now by exporting MAXCPU to the assembler. A better fix
might be to define these data structures in C - they're only referenced
in the kernel from C code these days anyway.
Approved by: re (kensmith)
o add driver callback to handle notification of beacon changes;
this is required for devices that manage beacon frames themselves
(devices must override the default handler which does nothing)
o move beacon update-related flags from ieee80211com to the beacon
offsets storage (or handle however a driver wants)
o expand beacon offsets structure with members needed for 11h/dfs
and appie's
o change calling convention for ieee80211_beacon_alloc and
ieee80211_beacon_update
o add overlapping bss support for 11g; requires driver to pass
beacon frames from overlapping bss up to net80211 which is not
presently done by any driver
o move HT beacon contents update to a routine in the HT code area
Reviewed by: avatar, thompsa, sephe
Approved by: re (blanket wireless)
- p_sflag was mostly protected by PROC_LOCK rather than the PROC_SLOCK or
previously the sched_lock. These bugs have existed for some time.
- Allow swapout to try each thread in a process individually and then
swapin the whole process if any of these fail. This allows us to move
most scheduler related swap flags into td_flags.
- Keep ki_sflag for backwards compat but change all in source tools to
use the new and more correct location of P_INMEM.
Reported by: pho
Reviewed by: attilio, kib
Approved by: re (kensmith)
does not have a rate table in older hal's so if we scan such a
channel the driver will hit an assertion or crash; for old hal's
fallback to using the static turbo rate table for this mode
(not correct but good enough for now given none of the rate
control algorithms understand how to switch between base+boost)
Approved by: re (blanket wireless)
mode works properly, previously the hostap channel could not be changed off #3.
Fix an ifp/sc misuse while I am here.
Reported by: many
Approved by: re (bmah)
- Fix panic from mutex unlock on freed lock when ASCONF-ACK
aborts an assoc
- Fix panic from addr lock recursion when ASCONFs are queued
in the front states
- ASCONFs "queued" in the front states should really be
bundled after the COOKIE-ACK, not in front of it
- Fix issue with addresses deleted in the front states from
being sent with ASCONF(DELETE)-- replaced
sctp_asconf_queue_add_sa() with delete specific function
- Comment change in sctp.h the drafts are now RFC's
Approved by: re@freebsd.org (B Mah)
of pages don't sum to anywhere near the total number of pages on amd64.
This is for the most part because uma_small_alloc() pages have never been
counted as wired pages, like their kmem_malloc() brethren. They should
be. This changes fixes that.
It is no longer necessary for the page queues lock to be held to free
pages allocated by uma_small_alloc(). I removed the acquisition and
release of the page queues lock from uma_small_free() on amd64 and ia64
weeks ago. This patch updates the other architectures that have
uma_small_alloc() and uma_small_free().
Approved by: re (kensmith)
status after vm_pager_put_pages() is VM_PAGER_PEND, then it could have
already been recycled, i.e., freed and reallocated to a new purpose;
thus, asserting that such pages cannot be written is inappropriate.
Reported by: kris
Submitted by: tegge
Approved by: re (kensmith)
MFC after: 1 week
change interrupt if the link is established with link parter. However
interrupt handler didn't acknowledge the interrupt if nfe(4) was not
running at the time of interrupt delivery. This caused endless
interrupt generation. Fix the bug by acknowledging the interrupt
regardless of running state of the driver.
PR: kern/116295
Submitted by: Mark Derbyshire (mark At taom dot com)
Approved by: re (kensmith)
per-primitive macros like MTX_NOPROFILE, SX_NOPROFILE or RW_NOPROFILE) is
not really honoured. In particular lock_profile_obtain_lock_failure() and
lock_profile_obtain_lock_success() are naked respect this flag.
The bug leads to locks marked with no-profiling to be profiled as well.
In the case of the clock_lock, used by the timer i8254 this leads to
unpredictable behaviour both on amd64 and ia32 (double faults panic,
sudden reboots, etc.). The amd64 clock_lock is also not marked as
not profilable as it should be.
Fix these bugs adding proper checks in the lock profiling code and at
clock_lock initialization time.
i8254 bug pointed out by: kris
Tested by: matteo, Giuseppe Cocomazzi <sbudella at libero dot it>
Approved by: jeff (mentor)
Approved by: re
incorrect and should be OFF letting IP fragment
large cookie-echos.
- Rename sysctl variable logging to log_level.
- Fix description of sysctl variable stats.
- Add sysctl variable log to make sctp_log readable via sysctl
mechanism (this is by compile switch and targets non KTR platforms or
when someone wants to do performance wise tracing).
- Removed debug code
Approved by: re@freebsd.org (B Mah)
stream (using EEOR mode). Changed to EINVAL (in sctp_output.c)
- Static analysis comments added
- fix in mobility code to return a value (static analysis found).
- sctp6_notify function made visible instead of
static (this is needed for Panda).
Approved by: re@freebsd.org (B Mah)
races for some struct thread members.
More specifically, this bug seems responsible for some memory dumping
problems people were experiencing.
Fix this adding correct thread locking.
Tested by: rwatson
Submitted by: tegge
Approved by: jeff
Approved by: re
matches the BPF registers (which are the only thing that is assigned
to/from BPF memory). This is a pedantic change that shouldn't change
any behaviour.
PR: 115931
Submitted by: Matthew Luckie <mjl@luckie.org.nz>
Approved by: re (bmah)
MFC after: 3 weeks
Fix a few while (!uart_getreg() & SR1_TNF) when
while (!(uart_getreg() & SR18TNF)) was really meant.
This driver should die anyway, it's awful, and uart_ns8250 should be fine
for the StrongArm 1110. I'll kill it later.
Submitted by: Mikhael Skvorts
Approved by: re (blanket)
prevents insmntque() from placing reallocated syncer vnode on mount
list, that causes panic in vfs_allocate_syncvnode().
Introduce MNTK_NOINSMNTQ flag, that marks the period when instmntque is
not allowed to success, instead of MNTK_UNMOUNT. The MNTK_NOINSMNTQ is
set and cleared simultaneously with MNTK_UNMOUNT, except on umount error
path, where it is cleaned just before the syncer vnode is going to be
allocated.
Reported by: Peter Jeremy <peterjeremy optushome com au>
Suggested by: tegge
Approved by: re (rwatson)
other changes too).
(without any real order)
1. Use device_get_nameunit for mutex naming
2. Add timer for low-latency playback
3. Move most mixer controls from sysctls to mixer(8) controls.
This is a largest part of this patch.
4. Add analog/digital switch (as a temporary sysctl)
5. Get back support for low-bitrate playback (with help of (2))
6. Change locking for exclusive I/O. Writing to non-PTR register
is almost safe and does not need to be ordered with PTR operations.
7. Disable MIDI until we get it to detach properly and fix memory
managment problems.
8. Enable multichannel playback by default. It is as stable as
single-channel mode. Multichannel recording is still an
experimental feature.
9. Multichannel options can be changed by loader tunables.
10. Add a way to disable card from a loader tunable.
11. Add new PCI IDs.
12. Debugger settings are loader tunables now.
14. Remove some unused variables.
15. Mark pcm sub-devices MPSAFE.
16. Partially revert (bus_setup_intr -> snd_setup_intr) since it need
to be done independently
Submitted by: Yuriy Tsibizov (driver maintainer)
Approved by: re (bmah)
The control input routine passes a NULL as its void argument when it
has reached the innermost header, which terminates the loop.
Reported by: Pawel Worach <pawel.worach@gmail.com>
Approved by: re
topology foo functions.
Working at the patch for topology problems in ia32/amd64 evicted some
problems regarding functions ordering in the SI_SUB_CPU family of
SYSINIT'ed subsystems.
In order to avoid problems with new modified to involved functions, a
correct ordering is not semantically specified for SI_SUB_CPU functions
(for a larger view of the issue please visit:
http://lists.freebsd.org/pipermail/freebsd-current/2007-July/075409.html )
Discussed with: peter
Tested by: kris, Rui Paulo <rpaulo@FreeBSD.org>
Approved by: jeff
Approved by: re
- duplicate #define in header, thanks to Kevin Lo for pointing out.
- incorrect BUSMASTER enable logic, thanks Patrick Oeschger
- 82543 fails due to bogus IO BAR logic
- Allow 82571 to use MSI interrupts
- Checksum Offload for UDP not working on 82575
Approved by:re
value, so we don't run out of KVA. The default vnodes limit fits better for
UFS, but ZFS allocated more file system specific memory for a vnode than UFS.
Don't touch vnodes limit if we detect it was tuned by system administrator
and restore original value when ZFS is unloaded.
This isn't final fix, but before we implement something better, this will
help to stabilize ZFS under heavy load on i386.
Approved by: re (bmah)
code comes from.
- Fix a LOR on Mac OS X: Do not hold an stcb lock when
calling soisconnected for a socket which has the
SS_INCOMP bit set on so_state.
- fix a comment to be non c++ style.
Approved by: re@freebsd.org (B Mah)
jumping to dropunlock to avoid a panic. While here move the calls to
ipsec4_in_reject() and ipsec6_in_reject() so they are after we obtain
the lock on inp.
Original patch to avoid panic: pjd
Review of locking adjustments: gnn, sam
Approved by: re (rwatson)
- Resort includes a bit.
- Correct typos and wording problems in comments.
- Rename udpcksum to udp_cksum to be consistent with other UDP-related
configuration variables.
- Remove indirection of udp_notify through local notify variable in
udp_ctlinput(), which is presumably due to copying and pasting from TCP,
where multiple notify routines exist.
Approved by: re (kensmith)
is given (with newfs or tunefs) and dirsize overflows.
In case dirsize is <= 0 because of an overflow set maxcontigdirs
to 0 so it will be 1 later. This is what would happen for large
fs_avgfilesize. [1]
Identified with help from: roberto, pjd
Submitted by: pjd [1]
Approved by: re (rwatson)
MFC after: 8 days
ioctl().
Note that other information provided by ifconfig(8) such like "list chan"
or "list ap" are still not available at this moment.
Before an(4) is connected to wlan(4), users are encouraged to use
ancontrol(8) to retrieve aforementioned information.
Reported by: dhw (http://lists.freebsd.org/pipermail/freebsd-current/2007-July/074848.html)
Reviewed by: ambrisko
Tested by: dhw
Approved by: re (bmah)
flags, the absense of these flags causes problems in other areas such as
bridging which expect them to be correct.
At the moment only Ethernet DLTs are checked.
Reviewed by: bms, csjp, sam
Approved by: re (bmah)
point to mac_check_vnode_unlink(), reflecting UNIX naming conventions.
This is the first of several commits to synchronize the MAC Framework
in FreeBSD 7.0 with the MAC Framework as it will appear in Mac OS X
Leopard.
Reveiwed by: csjp, Samy Bahra <sbahra at gwu dot edu>
Submitted by: Jacques Vidrine <nectar at apple dot com>
Obtained from: Apple Computer, Inc.
Sponsored by: SPARTA, SPAWAR
Approved by: re (bmah)
- fix the use after free seen when sending packets small enough to fit as an immediate
and bpf peers are present
- update to firmware rev 4.7 along with various small vendor fixes
Supported by: Chelsio
Approved by: re (blanket)
MFC after: 3 days
the recent send code, but uio may be NULL on sendfile
calls. Change to use sndlen variable.
- EMSGSIZE is not being returned in non-blocking mode
and needs a small tweak to look if the msg would
ever fit when returning EWOULDBLOCK.
- FWD-TSN has a bug in stream processing which could
cause a panic. This is a follow on to the codenomicon
fix.
- PDAPI level 1 and 2 do not work unless the reader
gets his returned buffer full. Fix so we can break
out when at level 1 or 2.
- Fix fast-handoff features to copy across properly on
accepted sockets
- Fix sctp_peeloff() system call when no true system call
exists to screen arguments for errors. In cases where a
real system call exists the system call itself does this.
- Fix raddr leak in recent add-ip code change for bundled
asconfs (even when non-bundled asconfs are received)
- Make sure ipi_addr lock is held when walking global addr
list. Need to change this lock type to a rwlock().
- Add don't wake flag on both input and output when the
socket is closing.
- When deleting an address verify the interface is correct
before allowing the delete to process. This protects panda
and unnumbered.
- Clean up old sysctl stuff and get rid of the old Open/Net
BSD structures.
- Add a function to watch the ranges in the sysctl sets.
- When appending in the reassembly queue, validate that
the assoc has not gone to about to be freed. If so
(in the middle) abort out. Note this especially effects
MAC I think due to the lock/unlock they do (or with
LOCK testing in place).
- Netstat patch to get rid of warnings.
- Make sure that no data gets queued to inactive/unconfirmed
destinations. This especially effect CMT but also makes a
impact on regular SCTP as well.
- During init collision when we detect seq number out
of sync we need to treat it like Case C and discard
the cookie (no invarient needed here).
- Atomic access to the random store.
- When we declare a vtag good, we need to shove it
into the time wait hash to prevent further use. When
the tag is put into the assoc hash, we need to remove it
from the twait hash (where it will surely be). This prevents
duplicate tag assignments.
- Move decr-ref count to better protect sysctl out of
data.
- ltrace error corrections in sctp6_usrreq.c
- Add hook for interface up/down to be sent to us.
- Make sysctl() exported structures independent of processor
architecture.
- Fix route and src addr cache clearing for delete address case.
- Make sure address marked SCTP_DEL_IP_ADDRESS is never selected
as src addr.
- in icmp handling fixed so we actually look at the icmp codes
to figure out what to do.
- Modified mobility code.
Reception of DELETE IP ADDRESS for a primary destination and
SET PRIMARY for a new primary destination is used for
retransmission trigger to the new primary destination.
Also, in this case, destination of chunks in send_queue are
changed to the new primary destination.
- Fix so that we disallow sending by mbuf to ever have EEOR
mode set upon it.
Approved by: re@freebsd.org (B Mah)
additional flags to many function calls. The flags only
get used in BSD when we compile with lock testing. These
flags allow apple to escape the "giant" lock it holds on
the socket and have more fine-grained locking in the NKE.
It also allows us to test (with witness) the locking used
by apple via a compile switch (manually applied).
Approved by: re@freebsd.org(B Mah)
- Fix copyrights, comments in UDPv6.
- Remove macro defines for in6pcb and udp6stat.
- Consistently refer to inpcbs as 'inp' and not also 'in6p'.
Reviewed by: gnn, jinmei, bz
Approved by: re (bmah)
TCP timers as a single timer, but retain the API changes necessary to
reintroduce this change. This will back out the source of at least two
reported problems: lock leaks in certain timer edge cases, and TCP timers
continuing to fire after a connection has closed (a bug previously fixed and
then reintroduced with the timer rewrite).
In a follow-up commit, some minor restylings and comment changes performed
after the TCP timer rewrite will be reapplied, and a further change to allow
the TCP timer rewrite to be added back without disturbing the ABI. The new
design is believed to be a good thing, but the outstanding issues are
leading to significant stability/correctness problems that are holding
up 7.0.
This patch was generated by silby, but is being committed by proxy due to
poor network connectivity for silby this week.
Approved by: re (kensmith)
Submitted by: silby
Tested by: rwatson, kris
Problems reported by: peter, kris, others
that can lead to a panic when the stick is yanked.
- make sure that zyd_attach() returns 0 or errno.
Submitted by: Weongyo Jeong <weongyo.jeong@gmail.com>
Reported by: Ted Lindgreen <ted@tednet.nl>
Reviewed by: sam
Approved by: re (blanket wireless)
with the INTR_FILTER-enabled MI code. Basically this consists of
registering an interrupt controller (of which there can be multiple
and optionally different ones either per host-to-foo bridge or shared
amongst host-to-foo bridges in any one machine) along with an interrupt
vector as specific argument for all the interrupt vectors used by a
given host-to-foo bridge (roughly similar to registering interrupt
sources on amd64 and i386), providing functions to enable, clear and
disable the interrupts of the children beneath the bridge.
This also includes:
- No longer entering a critical section in tl0_intr() and tl1_intr()
for executing interrupt handlers but rather let the handlers enter
it themselves so in the case of intr_event_handle() we don't enter
a nested critical section.
- Adding infrastructure for binding delivery of interrupt vectors to
specific CPUs which later on can be interfaced with the code from
amd64/i386 for binding interrupts to specific CPUs.
- Getting rid of the wrapper hack introduced along the lines of the
API changes for INTR_FILTER which as a side-effect caused interrupts
associated with ithread handlers only to get the elevated priority
of those associated with filters ("fast handlers") (this removes the
hack also in the non-INTR_FILTER case).
- Disabling (by not clearing) an interrupt in the interrupt controller
until all associated handlers have been executed, which is crucial
for the typical locking strategy of NIC drivers in order to work
correctly in case of shared interrupts. This was a more or less
theoretical problem on sparc64 though, as shared interrupts are
rather uncommon there except for the on-board SCCs and UARTs.
Note that due to the behavior of at least of some of the interrupt
controllers used on sparc64 an enable+EOI instead of a disable+EOI
approach (as implied by the INTR_FILTER MI code and implemented on
other architectures) is used as the latter can cause lost interrupts
or in the worst case interrupt starvation.
o Correct a typo in sbus_alloc_resource() which caused (pass-through)
allocations to only work down to the grandchildren of the bus, which
wasn't a real problem so far as we don't support any devices which are
great-grandchildren or greater of a U2S bridge, yet.
o In fhc(4) use bus_{read,write}_4() instead of bus_space_{read,write}_4()
in order to get rid of sc_bh and sc_bt in the fhc_softc. Also get rid
of some other unneeded members in fhc_softc.
Reviewed by: marcel (earlier version)
Approved by: re (kensmith)
o reset ni_inact when ni_inact_reload is changed so we're
assured a valid setting
o never let ni_inact go negative
o add a knob to disable hostap sta idle handling (e.g. so it can be done
by a user application)
o remove bogus reload on associate
Reviewed by: avatar
Approved by: re (blanket wireless)
o update ic_lastdata to reflect time of last outbound frame
o outbound traffic must preempt/cancel bg scanning to avoid delays
This stuff was somehow missed in the initial import.
Reviewed by: thompsa, avatar, sephe (earlier version)
Approved by: re (blanket wireless)
o add ic_extieee to hold the HT40 extension channel number
o add ic_state to track dynamic channel state for DFS
o add flags to mark regulatory channel requirements
o add state defs for DFS/radar support
Reviewed by: avatar
Approved by: re (blanket wireless)
o update 11n definitions to D2.0 spec
o add IEEE80211_CAPINFO_SPECTRUM_MGMT for DFS support
o add CSA ie definition for DFS support
o purge some unused definitions
o correct 802.11 reason and status codes
o correct reason code returned when a sta tries to associate to an
ap operating with WPA/RSN but without a WPA/RSN ie
Reviewed by: thompsa, avatar
Approved by: re (blanket wireless)
device and have had the crypto bits stripped from the 802.11 header
o strip mbuf flags in the rx path before passing up the stack
Reviewed by: thompsa, sephe, avatar
Approved by: re (blanket wireless)
The first drop was Beta, this code is expected to be the release version.
Note that this driver code will build in either 6.2 or 7. If you
use the code in 6.2 you will not get TSO or MSI/X support but it will
function in a legacy mode.
Approved by: re
used, rather than the one passed via 'req', which may not reflect a
rewrite. This call to useracc() is redundant to validation performed by
later copyin()/copyout() calls, so there isn't a security issue here,
but this could technically lead to excessive validation of addresses if
the length in newlen is shorter than req.newlen.
Approved by: re (kensmith)
Reviewed by: jhb
Submitted by: Constantine A. Murenin <cnst+freebsd@bugmail.mojo.ru>
Sponsored by: Google Summer of Code 2007
When any PnP device exists, isa_release_resource() is called with no
activated resource. So a bushandle is not allocated yet.
Approved by: re (kensmith)
can easily block in bread(), and then there was nothing to prevent the
static buffer (nambuf_{ptr,len,last_id}) being clobbered by another
thread.
The effects of the bug seem to have been limited to failed lookups and
mangled names in readdir(), since Giant locking provides enough
serialization to prevent concurrent calls to the functions that access
the buffer. They were very obvious for multiple concurrent tree walks,
especially with a small cluster size.
The bug was introduced in msdosfs_conv.c 1.34 and associated changes,
and is in all releases starting with 5.2.
The fix is to allocate the buffer as a local variable and pass around
pointers to it like "_r" functions in libc do. Stack use from this
is large but not too large. This also fixes a memory leak on module
unload.
Reviewed by: kib
Approved by: re (kensmith)
the callout_lock spin lock and the sleepqueue spin locks. In the fix,
callout_drain() has to drop the callout_lock so it can acquire the
sleepqueue lock. The state of the callout can change while the
callout_lock is held however (for example, it can be rescheduled via
callout_reset()). The previous code assumed that the only state change
that could happen is that the callout could finish executing. This change
alters callout_drain() to effectively restart and recheck everything
after it acquires the sleepqueue lock thus handling all the possible
states that the callout could be in after any changes while callout_lock
was dropped.
Approved by: re (kensmith)
Tested by: kris
needed at least to convince the BIOS to give us access to CPU freq
control on MacBooks.
Submitted by: Rui Paulo <rpaulo / fnop.net>
Approved by: re
MFC after: 5 days
active in failover mode rather than all interfaces with a link. This makes it
clear if the master interface is in use or one of the backup links.
Found by: Writing the Handbook section
Approved by: re (kensmith)
ktruserret() is invoked, an unlocked check of the per-process queue
is performed inline, thus, we don't lock the ktrace_sx on every userret().
Pointy hat to: jhb
Approved by: re (kensmith)
Pointy hat recovered from: rwatson
ZD1211/ZD1211B USB IEEE 802.11b/g wireless network devices. Not (yet)
connected to the build process (next batch of commits once I've looped
the current back back).
Submitted by: Weongyo Jeong
Reviewed by: sam@
Approved by: re@
