- Use "envctrl" as the name when registering this module rather than "pcf";
we can't have "pcf" as the name for all pcf(4) front-ends or we would get
conflicts.
OK'ed by: joerg
- s,pcf_,pcf_isa, to better reflect the purpose of this front-end and to
avoid conflicts.
- Don't use this front-end for attaching to EBus, declaring it as an EBus
driver was a cut&paste accident according to joerg.
OK'ed by: joerg, nsouch
its primary use is for the FEPS/FAS366 SCSI found in Sun Ultra 1e and 2
machines. Once the pci front-end is ported, this driver can replace the
amd(4) driver.
The code as-is is fairly stable. I've disabled tagged-queueing until I can
figure out a corruption bug related to it. I'm importing it now so that
people with these machines can (finally) stop netbooting and report bugs
before 5.3.
as otherwise the junk it contains may cause uhub_explore to give
up without ever trying to restart the port. This fixes the following
errors I was seeing with a VIA UHCI controller:
uhub0: port error, restarting port 1
uhub0: port error, giving up port 1
all of the interface between the driver and the bus. This will enable
us to stop special casing eisa bus attachments in modules and treat them
like we treat all other busses.
In the longer run, we need to eliminate much (all?) of these interfaces
and switch to using the standard bus_alloc_resource(), but that's not
done right now.
# I've not updated the modules to include eisa, etc, just yet
Tested on: Compaq Proliant 3000/333 purchased for eisa work
mode. The 5704 apparently has some s00p3r s33kr1t registers for setting
the advertisement of pause frame ability (i.e flow control) when in
autoneg mode. If we don't set these registers correctly, we may not
be able to negotiate a proper link with some switches. (Symptom is that
the NIC reports the link as up (PCS synched) but no traffic can be
exchanged.)
PR: kern/67598
different cards that matched vendor/id, but weren't wi cards. This is
because the vendor foolishly didn't have unique product ids. Symbol
has a serial card that would otherwise match the wi driver, for
example...
Taken from a patch for xe posted by: Carlos Velasco
which doesn't support ACPI power states. Return AE_NOT_FOUND for these
cases and don't print the warning message. Also, print the name of the
handle instead of device when unable to switch states. The device is often
not attached at this point and so its name is NULL, which doesn't help
debugging.
"stray irq 9" messages on my Thinkpad. It may also help with general
reboot consistency although the recent hang on reboot was solved by
acpi_cpu.c rev 1.39.
after. Unify the paths for all Cx states. Remove cpu_idle_busy and
instead do the little profiling we need before re-enabling interrupts.
Use 1 quantum as estimate for C1 sleep duration since the timer interrupt
is the main reason we wake.
While here, change the cx_history sysctl to cx_usage and report statistics
for which idle states were used in terms of percent. This seems more
intuitive than counters. Remove the cx_stats structure since it's no
longer used. Update the man page.
Change various types which do not need explicit size.
called ttyldoptim().
Use this function from all the relevant drivers.
I belive no drivers finger linesw[] directly anymore, paving the way for
locking and refcounting.
exactly as done in the cmi driver. I am quite confident this is
safe since I'm runing this for more than two weeks now, on an SMP
box. A few people tested this patch for me successfully as well.
- In subr_ndis.c, my_strcasecmp() actually behaved like my_strncasecmp():
we really need it to behave like the former, not the latter. (It was
falsely matching "RadioEnable", which defaults to 1 with "RadioEnableHW"
which the driver creates itself and to 0, because we were using
strlen("RadioEnable") as the length to test. This caused the radio to
always be turned off. :( )
- In if_ndis.c, only set IEEE80211_CHAN_A for channels if we actually
set any IEEE80211_MODE_11A rates. (ieee80211_attach() will "helpfully"
add IEEE80211_MODE_11A to ic_modecaps for you if you initialize any
802.11a channels. This caused "ndis0: 11a rates:" to erroneously be
displayed during driver load.)
- Also in if_ndis.c, when using TESTSETRATE() to add in any missing 802.11b
rates, remember to OR the rates with IEEE80211_RATE_BASIC, otherwise
comparing against existing basic rates won't match. (1, 2, 5.5 and
11Mbps are basic rates, according to the 802.11b spec.) This erroneously
cause 11Mbps to be added to the 11b rate list twice.
sysctls were global (hw.fxp_rnr and hw.fxp_noflow), all of them are
now per-device. Sample output of "sysctl dev.fxp0" with this patch,
with the standard %foo nodes removed :
dev.fxp0.int_delay: 1000
dev.fxp0.bundle_max: 6
dev.fxp0.rnr: 0
dev.fxp0.noflow: 0
protect the registers so it was trivially possible for a sync command and
i/o command to fight each other and confuse the controller. Make the
sync fib alloc/release functions inline and remove the somewhat worthless
AAC_SYNC_LOCK_FORCE flag. Thanks to Adil Katchi for helping me to track
this down in RELENG_4.
